GE 23114 Manual

NHL Tree Model No. 23114LO
LED 456 C7 LIGHTS
FOR INDOOR USE ONLY
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
READ AND FOLLOW ALL
a)
SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor
applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for
proper installation.
c) This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or
other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal
injury and electric shock it should not be played with or placed where
small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the
product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with
the product.
SAVE THESE INSTRUCTIONS
o)
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needles are
brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulation or cords, cracks in the
lampholders or enclosures, loose connections, or exposed copper wire.
d) When storing the product, carefully remove the product from wherever it
is placed, including tree, branches, or bushes, to avoid any undue strain
or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Replace the lamp.
The LED cover is designed to fit tightly on the lampholder.
To remove, twist cover while pulling. After replacing
the LED, align cover straight into lampholder,
push down and twist to ensure a secure fit.
1. Grasp plug and remove from the receptacle or
other outlet device. Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of
lampholder.
3. Replace lamp with only 3.3 Volt, 0.066 Watt,
LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and
gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in
each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps
in the light set so that the leads will touch the contacts inside the
lampholder.
CAUTION:
1. Replace lamps only with 3.3 volt, 0.066 watt spare
lamps provided with this product.
2. Risk of fire. This product does not contain lamp shunts, which allow the
product to operate if one lamp burns out. Do not replace lamps with
other than the spare lamps provided with this product.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning:
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at
1-877-398-7337 or visit us on the web at www.geholidaylighting.com
©2023 Nicolas Holiday Ltd.
246 Spring Hill Road, Unit B, Trumbull CT 06611
Suite 2706 Skyline Tower, 39 Wang Kwong Road, Kowloon Bay, Kowloon,
Hong Kong
GE is a trademark of General Electric Company and is under license by
Nicolas Holiday Ltd.
TROUBLESHOOTING
PROBLEM
If the
product
does not
light
If a based
LED is
① ②
missing
② ①
If an LED
FIG.1 FIG.2
fails to light
(shorts or
opens)
LEDs fail to
switch from
white to
multi
Changes or modifications to this unit not
FP-23 PRINTED IN CHINA
All rights reserved.
POSSIBLE CAUSE
One or more of the based Unplug the set at the outlet.
LEDs may have loosened Starting with the first unlit LED,
from the socket during gently push (don't twist) each
transporting. There is a LED base firmly into the socket.
break in the circuit If still does not light, then remove
between the LED leads each based LED and check for
and the socket terminals. out of place lead wires. Make
Male/female connectors certain connectors fully inserted
not fully inserted together. and securing cap fully tightened.
Non working control box. Step on foot pedal to turn LEDs
Foot pedal in off position. on.
One or more of the based Mark socket(s) with a piece of
bulbs may have come out tape and unplug the set. Replace
of the socket when the based LED or use one of the
transporting. spare based LEDs included with
product.
Incorrect LED, premature The LED may be out or dimly lit.
LED failure or voltage is Replace bad LEDs as soon as
too high. you find them.
If applicable, then a Contact Customer Support.
defective control box or
color change foot pedal.
CORRECTIVE ACTION