Advertisement
Quick Links
Scan to download the Prima User Guide
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, (800) 645-9445
For Technical Service, (800) 645-9440 or visit us at
Tech.NapcoSecurity.com
(Note: Technical Service is for security professionals only)
Publicly traded on NASDAQ
Symbol: NSSC
© NAPCO
NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for NAPCO Prima PHW8RETRO
Summary of Contents for NAPCO Prima PHW8RETRO
- Page 1 For Sales and Repairs, (800) 645-9445 For Technical Service, (800) 645-9440 or visit us at Tech.NapcoSecurity.com (Note: Technical Service is for security professionals only) Publicly traded on NASDAQ Symbol: NSSC © NAPCO NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-1...
- Page 2 FIRE +12V +12V EARTH +12V GND‒ 16VAC SUPV GND‒ Z1+ Z2+ GND‒ Z3+ Z4+ GND‒ Z5+ Z6+ GND‒ Z7+ Z8+ BATT+ BURG FIRE NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-1...
- Page 3 Connect to battery [+] terminal. Place shunt across P2 position 3 screw terminal, Zone Inputs 1 through 8 (labeled Z1+, Z2+, etc.), for to enable supervision. each zone 1 through 8, respectively. Connect the negative ground side NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-2...
- Page 4 Z1+ through Z8+ whereby the value of each normal zone condition is learned by the system. Within 3 seconds of shunting position 6, LED3 (at the top of the PC board) will blink to indicate the NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-3...
-
Page 5: Battery Monitoring
Remove shunt across header P2 position 2 to enable AC monitoring. Add one device at a time. Before adding a device, we recommend re- For the panel to be taken over, connect the AC terminal to the NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-4... - Page 6 For Technical Service, (800) 645-9440 or visit us at Tech.NapcoSecurity.com was previously used). Proceed as follows: (Note: Technical Service is for security professionals only) 1. Remove power. Publicly traded on NASDAQ Symbol: NSSC © NAPCO NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-5...
- Page 7 ALL WIRING EXCEPT BATTERY LEADS ARE POWER LIMITED. MAINTAIN 1/4-INCH SPACING BETWEEN BATTERY LEADS AND 2.2KΩ ALL OTHER WIRING (–) 12VDC Back BLACK Up Battery Battery used by the control panel to be "taken over" NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-6...
-
Page 8: Auxiliary Power Supply
Supervision Circuit (Power-Limited) EARTH GROUND *Install jumper J1 for AC supervisory circuit (NO) BLACK (–) (+) RED 12VDC Back Up Battery *Install jumper J1 for AC supervisory circuit (NO) NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-7... - Page 9 NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-8...
- Page 10 32° to 120.2°F (0° to 49°C) Relative Humidity (Storage) 85% Max. non-condensing Weather Proofing N/A, Indoor Use Only Dimensions (W x H x D) 6¾" x 3⅝" x 1½" (17.2 x 9.2 x 3.8cm) NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-9...
- Page 11 Correct -- Use UL Certified pigtail or wire nut / crimp connector Incorrect ductors used. NAPCO Prima: PHW8RETRO Takeover Module Installation Guide -- WI2716LF, Page 16-10...
Need help?
Do you have a question about the Prima PHW8RETRO and is the answer not in the manual?
Questions and answers