Advertisement
IMPORTANT KEEP FOR FUTURE REFERENCE
Read these instructions carefully before use and keep them for future reference. . Your
child' s safety may be affected if you do not follow these instructions.
Instruction leaflet
Feed Me Klic
Highchair mode
BS EN 14988:2017+A1:2020, BS EN 17191:2021 & BS EN 12520:2015
Customer Care Line: 01454 326 568
Seat mode
Advertisement
Table of Contents
Related Manuals for Red Kite Feed Me Klic
Summary of Contents for Red Kite Feed Me Klic
- Page 1 Read these instructions carefully before use and keep them for future reference. . Your child’ s safety may be affected if you do not follow these instructions. Instruction leaflet Feed Me Klic Highchair mode Seat mode BS EN 14988:2017+A1:2020, BS EN 17191:2021 & BS EN 12520:2015...
-
Page 2: Parts List
Parts List: B x 12 C x 2 E x 2 A x 1 D x 1 F x 2 I x 1 H x 1 G x 1 M x 1 L x 1 J x 1 K x 1 Screwdriver for assembly Assembly fixings (12 x screws) 2 x top support tubes (1 long and 1 short) - Page 3 To assemble the legs 1. Connect the rear legs (these have brackets attached to hang the tray on) on to the seat bucket rear fixings and secure in place with 2 screws. Repeat for the front legs. NOTE. Ensure the holes on the legs are facing inwards and the foot sits flat on the ground.
-
Page 4: Seat Installation
Seat installation 3. Line up the catches on the bottom of the seat plate with the two top supports by passing the plate through the back of the highchair just above the supports and press firmly down until they click in place. Clip the seat bucket on to the backrest and insert the front clip of the seat bucket into the slot on the front of the seat plate. - Page 5 Footrest and tray installation 4. Push the tray into the spring-loaded recess to attach the tray. Attach the footrest to the top of the front legs with the two threaded footrest fittings. CLICK Fig 4.
-
Page 6: Tray Adjustment
Tray adjustment 5. Press the buttons on the sides of the tray to move it forwards or backwards. Fig 5. -
Page 7: Tray Removal
Tray removal 6. Press the buttons on the bottom of the tray and lift upwards to remove it. PRESS Fig 6. - Page 8 To fold the highchair 7. Press in both buttons located on the bottom rear of the seat plate and slide the rear legs towards the front legs to fold it. PRESS PRESS Fig 7.
- Page 9 To secure and adjust the harness 8. To open the harness, press the centre button (A). Place the child in the seat and put their arms through the shoulder and waist harness (B) and push the buckles back into the centre buckle to secure the child. Adjust the sliders (C) to achieve a snug and comfortable fit.
- Page 10 To convert to Chair mode (Seat removal) 9. Push the tab on the bottom front of the seat forwards and upwards to unclip the front. Continue to lift upwards so that the back of the seat unclips to completely remove it. Remove the footrest from the top of the legs and reattach it to the holes on the bottom of the legs.
-
Page 11: Care Advice
• Inspect all studs, nuts and screws for tightness. Check that all straps and harness attachment points are in good working order. • Do not use replacement parts other than those approved by Red Kite. Failure to do this may invalidate your warranty. - Page 12 (where provided) and seat or to climb in and out of the high chair. • Only use the highchair on a level floor surface. • Never add accessories or fittings that have not been approved by Red Kite. • BS EN 14988:2017+A1:2020...
- Page 13 • Do not use the seating if any part is broken, torn or missing and use only spare parts approved by Red Kite. • BS EN 12520:2015 For all technical queries please call: 01454 326 568 Manufactured by: The Red Kite Baby Co Ltd. 35 Lavenham Road, Beeches Industrial Estate, Yate, Bristol, BS37 5QX. UK.
Need help?
Do you have a question about the Feed Me Klic and is the answer not in the manual?
Questions and answers