Subscribe to Our Youtube Channel
Related Manuals for Ruijie Reyee RG-ANT16S-120
Summary of Contents for Ruijie Reyee RG-ANT16S-120
- Page 1 Ruijie Reyee RG-ANT16S-120 Antenna Hardware Installation and Reference Guide Document Version: V1.2 Date: 2024-03-28 Copyright © 2024 Ruijie Networks...
- Page 2 All rights are reserved in this document and this statement. Any reproduction, excerption, backup, modification, transmission, translation or commercial use of this document or any portion of this document, in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
-
Page 3: Preface
Preface Audience This document is intended for: Network engineers Technical support and servicing engineers Network administrators Technical Support Official Website of Ruijie Reyee: https://reyee.ruijie.com Technical Support Website: https://reyee.ruijie.com/en-global/support Case Portal: https://www.ruijienetworks.com/support/caseportal Community: https://community.ruijienetworks.com ... - Page 4 Note An alert that contains additional or supplementary information that if not understood or followed will not lead to serious consequences. Specification An alert that contains a description of product or version support. Note This document provides the installation steps, troubleshooting, technical specifications, as well as the specifications and use guidelines of cables and connectors.
-
Page 5: Table Of Contents
Contents Preface ..............................I 1 Product Introduction .......................... 1 1.1 Overview ............................ 1 1.2 Package Contents........................1 1.3 Product Appearance ........................2 1.3.1 Appearance ........................2 1.3.2 Antenna Connectors ...................... 3 1.4 Specifications ..........................4 2 Preparing for Installation ........................6 2.1 Safety Precautions ........................ - Page 6 3.3 Safety Precautions During Installation ..................10 3.4 Installation Procedures ......................10 3.4.1 Installing the Wireless Bridge ..................10 3.4.2 Removing the Wireless Bridge ..................12 3.4.3 Installing the Antenna....................14 3.5 Connecting Cables........................16 3.6 Verifying the Installation ......................16 4 Debugging ............................
-
Page 7: Product Introduction
Product Introduction Overview The RG-ANT16S-120 antenna is an external sector antenna launched by Ruijie Reyee for outdoor bridges. This antenna, featuring the 5 GHz 2x2 MIMO technology and two spatial streams, delivers a gain of up to 16 dBi, with a horizontal angle of 120° and a vertical angle of 10° . It is specifically designed for the RG-AirMetro550G- B bridge for PTMP scenarios, covering a range of up to 5 km. -
Page 8: Product Appearance
Hardware Installation and Reference Guide Product Introduction Product Appearance 1.3.1 Appearance Figure 1-1 Appearance Front view Back view... -
Page 9: Antenna Connectors
Hardware Installation and Reference Guide Product Introduction Note The label is located on the back of the device. 1.3.2 Antenna Connectors Figure 1-2 Antenna Connectors Table 1-2 Antenna Connectors Mark Item Description -45° Antenna path 1 connector +45° Antenna path 2 connector... -
Page 10: Specifications
Hardware Installation and Reference Guide Product Introduction Specifications Table 1-3 Specifications Dimensions 361 mm × 110 mm × 48.5 mm (14.21 in. × 4.33 in. × 1.91 in.) (excluding mounting bracket) Weight 2.5 kg (5.51 lbs.) (including packaging) Frequency Range 5.15 - 5.85 GHz Gain 16 dBi... - Page 11 Hardware Installation and Reference Guide Product Introduction Warning Operation of this equipment in a residential environment could cause radio interference.
-
Page 12: Preparing For Installation
Hardware Installation and Reference Guide Preparing for Installation Preparing for Installation Safety Precautions Note To prevent device damage and physical injury, please read carefully the safety precautions described in this chapter. The following safety precautions do not cover all possible dangers. 2.1.1 General Safety Precautions ... -
Page 13: Installation Environment Requirements
Hardware Installation and Reference Guide Preparing for Installation Installation Environment Requirements To ensure normal operation and a prolonged service life of the device, the installation site must meet the following requirements. 2.2.1 Environment Install the device in a well-ventilated environment. If it is installed in a closed room, make sure there is a good cooling system. -
Page 14: Tools
Hardware Installation and Reference Guide Preparing for Installation Keep the device away from the grounding facility or lightning and grounding facility of the power device as much as possible. Keep the device away from high-power radio stations, radar stations, and high-frequency high-current devices. -
Page 15: Installation
Hardware Installation and Reference Guide Installation Installation Caution Before installing the device, make sure that you have carefully read the requirements described in Chapter 2. Installation Procedure Before You Begin Carefully plan and arrange the installation location, networking mode, power supply, and cabling of the device before installation. -
Page 16: Safety Precautions During Installation
Hardware Installation and Reference Guide Installation Safety Precautions During Installation To ensure minimal interference when installing multiple wireless bridges in close proximity, maintain a horizontal installation distance of at least 2 meters, or a vertical installation distance of at least 0.5 meters between each wireless bridge. - Page 17 Hardware Installation and Reference Guide Installation (2) Attach the wireless bridge to the antenna. (3) Connect the SMA connector of the wireless bridge to that of the antenna.
-
Page 18: Removing The Wireless Bridge
Hardware Installation and Reference Guide Installation (4) Install the protective cover. 3.4.2 Removing the Wireless Bridge (1) Remove the protective cover by pulling it upward. (2) Unscrew the RF cable. - Page 19 Hardware Installation and Reference Guide Installation (3) Remove the wireless bridge by pulling it upward and then outward. (4) Remove the RF cable.
-
Page 20: Installing The Antenna
Hardware Installation and Reference Guide Installation 3.4.3 Installing the Antenna Note You are advised to use the following three Ruijie antenna models: RG-ANT20S-90, RG-ANT16S-120, and RG- ANT13-360. Installing a 120° antenna (1) Secure the mounting bracket to the antenna with four screws. - Page 21 Hardware Installation and Reference Guide Installation (3) Secure the antenna to the pole. Note M8 x 150 mm screws are recommended.
-
Page 22: Connecting Cables
Hardware Installation and Reference Guide Installation Connecting Cables (1) Use or make an Ethernet cable based on the distance between the wireless bridge and the power source. The device supports PoE power supply over Cat5e or better cables with a cable length up to 100 meters (328 ft.). -
Page 23: Debugging
Hardware Installation and Reference Guide Debugging Debugging Setting Up the Configuration Environment Before setting up the configuration environment using the 24 V, 0.5 A PoE power supply or the 12 V DC power supply, verify that the power cord is properly connected and that the configuration environment meets safety requirements. -
Page 24: Monitoring And Maintenance
Monitoring and Maintenance Hardware Installation and Reference Guide Monitoring and Maintenance Monitoring You can observe the LED status to monitor the device in operation. Hardware Maintenance If the hardware is faulty, please contact Ruijie Networks technical support for assistance. -
Page 25: Common Troubleshooting
Hardware Installation and Reference Guide Common Troubleshooting Common Troubleshooting Troubleshooting Flowchart... -
Page 26: Appendix
Hardware Installation and Reference Guide Appendix Appendix Connectors and Media 1000BASE-T/100BASE-TX/10BASE-T Port The 1000BASE-T/100BASE-TX/10BASE-T port is a 10/100/1000 Mbps auto-negotiation port that supports auto MDI/MDIX Crossover. Compliant with IEEE 802.3ab, the 1000BASE-T port requires Category 5e 100-ohm UTP or STP (recommended) with a maximum distance of 100 meters (328 feet). - Page 27 Hardware Installation and Reference Guide Appendix The following figure shows feasible connections of the straight-through and crossover twisted pair cables for a 100BASE-TX/10BASE-T port. Figure 7-2 100BASE-TX/10BASE-T Twisted Pair Connections Straight-Through Crossover Switch Adapter Switch Switch...
Need help?
Do you have a question about the Reyee RG-ANT16S-120 and is the answer not in the manual?
Questions and answers