Subscribe to Our Youtube Channel
Related Manuals for HYXIPOWER HYX-EA2000 Series
Summary of Contents for HYXIPOWER HYX-EA2000 Series
- Page 1 HYX-EA2000 Series Portable Power Station User Manual Before using the product, please read this manual carefully and keep it properly Zhejiang Hyxi Technology Co., Ltd. for future reference!
- Page 2 Notice to Customers Dear customer, thank you for choosing our products and services. Before using the product, please read this user manual carefully to have a clear understanding based on which you can use the product successfully. Once you use this product, it is considered that you have understood, approved, and accepted all the terms and service contents specified in the user manual.
-
Page 3: Table Of Contents
Contents I. Safety Guidelines ....................1 Safety precautions ....................1 Disposal ........................2 II. Product Introduction ..................3 1. Product appearance ....................3 2. UI…… .......................... 4 3. Specifications ......................5 III. Use of the product ................... 7 1. -
Page 4: Safety Guidelines
I. Safety Guidelines Safety precautions 1. Do not immerse the product into liquid or water, or make it hygroscopic. If there is dirt on the surface or interface of the product, use a dry cloth to clean it. 2. It is strictly forbidden to put the product near a heat source, combustion source, or heating furnace to prevent the hazards because the product becomes overheated. -
Page 5: Disposal
10. If the product catches fire by accident, it is recommended that you use extinguishing devices in the following order: sand, fire blanket, dry powder, and carbon dioxide extinguisher. 11. If the product is seriously damaged, do not touch the exposed cell. For safety, place the product in an open area, away from combustibles and people, and then retire it in accordance with local laws and regulations. -
Page 6: Product Introduction
II. Product Introduction This product is a portable power station, with a battery capacity of 1872 Wh and rated output power of 2000 W. It has built-in high-rate lithium iron phosphate (LFP) power cells with excellent safety. This product provides the bidirectional inverter function. The AC output is a pure sine wave of voltage, ranging from 220 V to 240 V (50/60 Hz), and the rated output power is 2000 W. - Page 7 2. UI Alarm EPS function High temperature protection Charging gear Low temperature protection Overload protection AC input Battery percentage AC output startup AC input mode Fan operation Remaining discharging / charging time DC output startup Input power USB output startup Output power For more information about fault display and handling, refer to Chapter 4.
-
Page 8: Specifications
3. Specifications Basic specifications 51.8 × 29.3 × 32.3 cm/20.4 × 11.5 × 12.7 in Net weight 22.5 kg/49.6 lbs Size Battery capacity 1872 Wh (39000 mAh/48 V) Cycle life 4000 times Rated power 2000 W, peak power of 3300 W Cell type Lithium iron phosphate battery... - Page 9 Use conditions °C °C °F °F Operating temperature to 45 to 113 °C °C °F °F Charging temperature to 40 to 104 Working environment humidity 20 to 90% RH (no condensation) °C °C °F °F Storage temperature to 45 to 113 Storage environment humidity <...
-
Page 10: Use Of The Product
III. Use of the product 1. Use of the product Power-on/off The main power switch controls the product to power on or power off. Press the main power switch to power on the product. In power-on state, long-press the main power switch for 2 seconds to power off the product. In power-on state you can press the main power switch to make the display switch between on and off states. - Page 11 DC output switch will turn off automatically. USB output Turn on the main power supply. Press the USB output switch. After that, the USB power supply is started, the USB-A and Type-c ports start to output power supply, and the USB switch indicator is turned on at the same time.
-
Page 12: Ac Charging
2. AC charging After the AC input charging port is connected to the mains: In power-off state, the product wakes up automatically and charges the battery in accordance with the preset charging power. When the 230 V AC output is operating properly, it will switch to EPS mode for power supply and start charging the battery at approximately 300 W. -
Page 13: Solar Charging
Note: In smart car charging mode, if the car engine is not working, car charging is not performed so as to protect the 12 V battery. Car charging can be performed normally only after the car engine starts working. 4. Solar charging After the DC input charging port is connected to a solar panel, the product intelligently identifies photovoltaic charging and automatically performs Maximum Power Point Tracking (MPPT):... -
Page 14: Indicator
Note: The power supply in EPS mode involves switching time and cannot replace professional UPS products. When using EPS mode, you need to confirm whether the power demands of electrical appliances are satisfied. To use the EPS function, ensure that the load does not exceed the rated power. -
Page 15: Fault Display And Handling
IV. Fault Display and Handling Warning icon Fault type Handling Remarks Flashing: The rated The load exceeds the load capacity AC output power is exceeded of the product. termination and but no protection is 1. When the fault occurs, press the overload performed. - Page 16 The USB power Check whether the load capacity of USB output supply is faulty, and the product is exceeded. termination. the output is 1. When the fault occurs, press the abnormal. USB output switch to clear the alarm. 2. If the alarm indicates that the load capacity of the product is exceeded, reduce the load and press the USB output switch again to make the...
- Page 17 If the two It is detected that the power device Output indicators flash at temperature is too low. Wait the termination. the same time, it temperature to change to normal indicates a low before using the product again. temperature alarm of the power device.
-
Page 18: Package Contents
V. Package Contents Power station AC charging cable Car charging cable User manual and warranty card VI. Maintenance It is recommended that the product be in long-term backup power mode. If the product needs to be stored for a long period of time, charge and discharge it once every three months (that is, first discharge the product to 30% of the full capacity, and then charge the product to 60%.) To ensure the service life of the product and safety, do not store this product in an... -
Page 19: Disclaimer And Safety Warnings
providing services or charge the cost of parts and services in the following circumstances: 1. The appearance of the product is damaged after use. 2. Unauthorized disassembly and maintenance of non-professionals. 3. Performance problems caused by human factors. 4. Damage caused by natural disasters, lightning strikes, accidents, and other irresistible factors. - Page 20 This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU. WEEE Directive–2012/19/EU The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner. Battery Directive-2013/56/EC Battery in the product complies with the European Battery Directive 2013/56/EC.
Need help?
Do you have a question about the HYX-EA2000 Series and is the answer not in the manual?
Questions and answers