Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Griesser Progreso 1M
Summary of Contents for Griesser Progreso 1M
- Page 2 Progreso 1M Nr. 179085 Operating instructions Please take care of the operating instructions! ©2013 by Griesser AG Tänikonerstrasse 3 CH-8355 Aadorf Tel +41 58 822 42 42 Fax +41 58 822 43 43 www.griessergroup.com 181222501_EN_0313...
-
Page 3: Table Of Contents
Contents Device explanation Warnhinweise on front of device Device explanation ............EN 3 Safety instructions/exclusion of liability ......EN 4 Scope of supply/ intended use ........EN 6 Bidirectional radio system/unidirectional radio system EN 7 Mounting of the wall bracket ..........EN 9 Explanation of functions .......... -
Page 4: Safety Instructions/Exclusion Of Liability
• The device may only be used by persons who have It is essential to observe these operating instructions for use if read and understood the operating instructions. the Progreso 1M hand-held transmitter is to be used safely and if the various product characteristics and performance features are Operation to be achieved. -
Page 5: Scope Of Supply/Intended Use
• CE mark confirmation back to the transmitter. The status LED lights up briefly for confirmation. Scope of supply Progreso 1M (batteries (2 x LR 06; AA) supplied with device) What is a unidirectional radio system? Wall bracket 2 dowels... -
Page 6: Mounting Of The Wall Bracket
Safety instructions for radio operation Mounting of the wall bracket Warnhinweise C A U T I O N ! N O T I C E ! The wall bracket has to be fixed so that the drill Observe the following safety instructions for radio holes don’t touch any electrical lines. -
Page 7: Explanation Of Functions
Explanation of functions Explanation of functions Warnhinweise Status LED Select button (AUTO switching button) A radio signal is displayed by the illumination of the Status LED Pressing the Select button briefly allows the current status of (LED ring around the STOP button). the programmed receiver and the hand-held transmitter to be queried. -
Page 8: Programming The Transmitter
2. Press the UP button immediately after the start of upward travel The blind/shutter will stop. (max. 1 second). The Progreso 1M is now programmed. The status LED lights up briefly. The blind will stop – start moving again – stop and then move in the DOWN direction. -
Page 9: Venetian Blind
Approach limit positions Intermediate positions for roller shutters/ Warnhinweise Roller shutter/awning/venetian blind awnings/venetian blinds P R E R E Q U I S I T E ! Roller shutters Awning Venetian blind The transmitter/transmitter channel has been programmed. The end positions of the drive have been set. Pos ▼... -
Page 10: Program Ventilation/Tilting Position
Intermediate positions for roller shut- Delete positions Warnhinweise ters/ awnings/venetian blinds Program ventilation/tilting position Delete intermediate position P R E R E Q U I S I T E ! 1. Press the STOP button and also the DOWN button. The transmitter/transmitter channel has been 2. -
Page 11: Deletion Of All Transmitters
Battery changing/cleaning/disposal Delete transmitter/technical data Warnhinweise Battery replacement Delete transmitter/channel 1. Press the STOP button and also the programming button P N O T I C E ! (back of unit). • Replace batteries only with identical type 2. Hold down this button combination for approx. 6 seconds until (2 x LR 06;... -
Page 12: Notes On Troubleshooting
– Accompanying conditions – Item description – Own presumption – Type of fault – Previously occurring unusual events Repair address: Griesser AG Tänikonerstrasse 3 CH-8355 Aadorf Tel +41 58 822 42 42 Fax +41 58 822 43 43 www.griessergroup.com EN 20...
Need help?
Do you have a question about the Progreso 1M and is the answer not in the manual?
Questions and answers