Related Manuals for VOCiC RLD-100W01A
Summary of Contents for VOCiC RLD-100W01A
- Page 1 VOCIC ELECTRIC WHEELCHAIR INSTRUCTION MANUAL >>> Model:RLD-100W01A >>> SKU:V-EW-V56-E-SV • English P2-17 • Deutsch P18-33 service-eu@vocic.com...
-
Page 2: Table Of Contents
..........17 Thank you for purchasing a VOCIC Electric Wheelchair! The VOCIC Electric Wheelchair has been developed with a lot of atten- tion to safety and will support you in your everyday life. Please read these directions carefully before you start using the product and keep them for future reference. -
Page 3: I.safety Instruction
I. Safety Instructions ■ WARNING Please read carefully before use. Do not modify the wheelchair by yourself without consent.Please be sure to abide by it. Failure to comply may lead to product damage and personal injury. 1. Not suitable to climb a long slope to avoid overloading and excessive power consumption of the circuit and motor. - Page 4 ■ Technical Data Model V-EW-V56-E-SV Item Dimensions before folding (L*W*H) 118.5*64*97cm Dimensions after folding (L*W*H) 78*40*72cm Seat Width 46.5cm Seat Depth 44cm Seat Height 51.5cm Backrest Height 43cm Front Wheel Dia. 25cm Rear Wheel Dia. 40cm Gross Weight 38.5Kg Net Weight 34.35Kg 125Kg Load-Bearing...
-
Page 5: Iii.assembly Instructions
Check the contents for completeness and make sure nothing is damaged. Should you find any irregularities or damaged, please contact our customer service (service-eu@vocic.com). 1. Unpack the box, take out the folded electric wheelchair, and place the electric wheelchair on the ground. - Page 6 3: Tighten the support beam Find the support beam behind the backrest, grab the beam with your hands and pull it down make it tense and horizontal at about 180 degrees .(as figure 6/7) please note: if the beam is not in a tight state, the cushion may not be able to main- tain a level and cause you to sit in a wheelchair with unstable state.
- Page 7 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 6:Controller installation (1)Insert controller bracket mandrel into right armrest tube hole(as figure 16), Tighten the white knob downwards until it cannot be tightened (as figure 17) Figure 16 Figure 17 (2): Find the round buckle (organize cables) in the packaging bag , pinch the larger side of the opening to support the smaller side (as shown in Figure 18), and insert the smaller side into...
- Page 8 7: Install the seat cushion pad and backrest pad (1) Install the seat cushion pad: Align Velcro on both sides of the cushion and cushion pad in advance (as shown in Figure 21), then glue them together and press them tightly with both hands (as shown in Figure 22) Figure 21 Figure 22...
- Page 9 8: Foot pedal installation (1) Take out the foot pedal, align the foot pedal "1" with "5" in advance (as shown in Figure 25), and insert "1" into "5", while ensuring that "3" is inserted into the silver pipeline (as shown in Figure 26) Figure 25 Figure 26 (2) Pull '2' upwards to align '6', then loosen '2' to insert '4' into '6'(as shown in Figure 27/28)
- Page 10 Remove the Velcro from the leggings cloth and install it on the silver pipes on both sides of the pedal. Simply stick the Velcro together. Please note that the VOCIC logo is located on the left side to avoid installation errors...
- Page 11 ■ Folding Method When you fold the electric wheelchair, you need to switch to manual mode to ensure that the control ler is turned off to avoid wasting power. Turn off 1: Removing the battery Firstly, you need to loosen the rubber, then disconnect the power cord and remove the battery (refer to page 6 ) 2: Then release the support beam upwards to ensure a relaxed state of settlement Please note：...
-
Page 12: Iv.using Introduction
IV. Using Introduction 1. Controller Function Description 6 Battery Chart 2 Turn on/ Turn off 5 Horn 4 Speed Chart 3 Speed down - 3 Speed up + 1 Joystick 1 Joystick : As shown in Figure 1, push the joystick to control the direction and speed of the wheelchair. When the joystick is facing forward, the chair moves forward;... - Page 13 2. Electronic Brake The advanced electronic brake system ensures safe parking under any road conditions. Note: If you turn on the electric mode for a long time, the power consumption will be very fast, we recommend turning off the electric mode if you are not using it 1.Support electric and manual modes.
- Page 14 3. Electric Wheelchair Operation 1: When seated well, fasten the seat belt and press the power switch on the controller. When a prompt sound is heard, it indicates that the electric wheelchair has been activated. Turn on 2: Operate the joystick to move forward, the joystick can be rotated 360 degrees to adjust the direction, push it forward to walk forward, push it backward to go backward, and turn left to turn left.
- Page 15 7: Folding armrest (1) First, locate the black button located below the armrest (as shown in Figure 37) (2) Press down with your hand (as shown in Figure 38) (3) When the black button appears in the state shown in Figure 39. (4) Lift the armrest with your hand until it disengages from the armrest pipe ( Figure 40) (5) The armrest is flipped approximately 180 degrees (as shown in Figure 41)
- Page 16 4. Charging Important Content: This electric wheelchair has 1 battery. The battery is detachable, ensure that there are no dangerous objects around when charging, and pay attention to safety,and when charging please turn off controller. Charging Methods Method 1: Controller Charging You only need to connect the charging port of the controller to charge.
-
Page 17: V.after-Sales Service
1. Replacing of Parts Wearable parts such as tires are subject to wear and tear. Please contact us for the replacement of parts if necessary. 2. Warranty We provide 5 years warranty. Contact If you have any questions, please contact us: service-eu@vocic.com...
Need help?
Do you have a question about the RLD-100W01A and is the answer not in the manual?
Questions and answers
esta silla lleva bateria de litio? que precio tiene de nueva