Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for LTS Security LTH-M001
Summary of Contents for LTS Security LTH-M001
- Page 1 Video Intercom Vandal-Resistant Door Station Quick Start Guide...
- Page 2 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Quick Start Guide This quick start guide is intended for users of the vandal-resistant door station. It includes instructions on how to use the Product. The software embodied in the Product is governed by the user license agreement covering that Product.
- Page 3 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Page 4 Video Intercom Vandal-Resistant Door Station·Quick Start Guide 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
- Page 5 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death.
- Page 6 Video Intercom Vandal-Resistant Door Station·Quick Start Guide When the product is installed on wall or ceiling, the device shall be firmly fixed. If smoke, odors or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
- Page 7 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Please use the provided glove when open up the device cover, avoid direct contact with the device cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
-
Page 8: Table Of Contents
Video Intercom Vandal-Resistant Door Station·Quick Start Guide Table of Contents 1 Introduction ..................1 1.1 Overview.................. 1 1.2 Features ................... 1 2 Appearance ..................3 3 Terminals and Wiring ..............4 3.1 Terminals and Interfaces ............4 3.2 Wiring Description ..............5 3.2.1 Door Lock Wiring .............. -
Page 9: Introduction
1 Introduction 1.1 Overview The vandal- resistant door station is a kind of door station in the video intercom system. Featuring in the vandal- resistant design, convenient installation, and easy operation, the door station supports the video intercom function, access control function, door magnetic alarm, motion detection, and so on. - Page 10 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Low illumination Alarm Functions Supports the door magnetic alarm Auto-uploads alarm messages to the master station or the client software Remote Controls Remote reboot, remote upgrade, time synchronization via NTP, and batch configuration function ...
-
Page 11: Appearance
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 2 Appearance Figure 2-1 Door Station Overview Table 2-1 Components Description Description Microphone Built-in Camera Low Illumination Supplement Light Call Button Loudspeaker... -
Page 12: Terminals And Wiring
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 3 Terminals and Wiring 3.1 Terminals and Interfaces Figure 3-1 Terminals and Interfaces Table 3-1 Descriptions of Terminals and Interfaces Name Interface Description Power 12 VDC Power Supply 12 VDC Supply Input Network Interface (PoE Supported) Alarm Input ALARM... -
Page 13: Wiring Description
Video Intercom Vandal-Resistant Door Station·Quick Start Guide Name Interface Description (Connect Electric Bolt or Magnetic Lock) 3.2 Wiring Description 3.2.1 Door Lock Wiring Terminal NC/COM is set as default for connecting magnetic lock/electric bolt; terminal NO/ COM is set as default for connecting electric strike. -
Page 14: Door Magnetic Wiring
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 3.2.2 Door Magnetic Wiring To connect door magnetic, it is required to set the output of terminal AI to be door status via Batch Configuration Tool or the client software or the web browser. Figure 3-3 Door Magnetic Wiring 3.2.3 Exit Button Wiring To connect exit button, it is required to set the output of terminal AI... -
Page 15: Alarm Device Input Wiring
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 3.2.4 Alarm Device Input Wiring When you set the output of terminal AI to be custom via Batch Configuration Tool or the client software or the web browser, you can connect any alarm input device to the door station via the terminal Figure 3-5 Alarm Device Input Wiring... -
Page 16: Installation
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 4 Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. The device supports two ways of power supply: 12 VDC, or PoE power supply. -
Page 17: Wall Mounting
Video Intercom Vandal-Resistant Door Station·Quick Start Guide Wall Mounting Steps: 1. Fix the wall mounting plate to the wall with 4 expansion screws. Wall Mounting Plate Expansion Screws Figure 4-2 Install the Plate 2. Insert terminal blocks into the interfaces of the door station body, and connect the network cable. - Page 18 Video Intercom Vandal-Resistant Door Station·Quick Start Guide 3. Fix the door station body to the protective shield tightly. Protective Shield Door Station Main Body Figure 4-4 Fix the Body to the Shield 4. Hook the door station to the wall mounting plate tightly. Hooks Figure 4-5 Hook the Door Station to the Plate 5.
- Page 19 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Set Screw Rubber Plug Figure 4-6 Secure the Door Station...
-
Page 20: Remote Operation
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 5 Remote Operation 5.1 Activating Device Purpose: You are required to activate the device first by setting a strong password for it before you can use the device. Activation via Batch Configuration Tool, Activation via Web Browser, and activation via the client software are supported. -
Page 21: Activation Via Batch Configuration Tool
Video Intercom Vandal-Resistant Door Station·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create to a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. - Page 22 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Figure 5-3 Activation Interface (Batch Configuration Tool) 3. Create a password, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create to a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
-
Page 23: Editing Network Parameters
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 5.2 Editing Network Parameters Purpose: To operate and configure the device via LAN (Local Area Network), you need connect the device in the same subnet with you PC. You can edit network parameters via batch configuration tool, the client software, and web browser. -
Page 24: Adding Device
Video Intercom Vandal-Resistant Door Station·Quick Start Guide Figure 5-5 Edit Network Parameters The default port No. is 8000. After editing the network parameters of device, you should add the devices to the device list again. 5.3 Adding Device To configure the activated device via batch configuration tool and the client software remotely, you should add the device to the tool or the software first. -
Page 25: Adding Device By Ip Address
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 1. Select an active online device or hold the Ctrl or Shift key to select multiple devices in the online devices list. Figure 5-6 Online Devices Interface 2. Click the button to pop up the login dialog box. Figure 5-7 Login Dialog Box 3. - Page 26 Video Intercom Vandal-Resistant Door Station·Quick Start Guide 1. Click the button to pop up the adding devices dialog box. Figure 5-8 Adding Button 2. Select IP Address in the adding mode drop-down list. 3. Input the IP address, and set the port No., user name and password of the device.
-
Page 27: Accessing Via Web Browser
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 5.4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 to 11 Steps: 1. - Page 28 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Figure 5-11 Downloading Plug-in 6. Reopen the web browser after the installation of the plug-in, and repeat steps 2 to 4 to login. The default IP address of the device is 192.0.0.65. ...
-
Page 29: Local Operation
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 6 Local Operation Before you start: Make sure the door station has been activated. Make sure the network cable is well-connected. Purpose: You can call the resident (the indoor station) or the center (the master station) via the door station by pressing or holding the call button. - Page 30 Video Intercom Vandal-Resistant Door Station·Quick Start Guide Besides the indoor station, you can also unlock the door by the master station, the client software, and the web. When the video intercom between you and the resident is realized, you can speak to the resident, and the live view of door station will be displayed on the connected indoor station.
-
Page 31: Appendix
Video Intercom Vandal-Resistant Door Station·Quick Start Guide 7 Appendix Installation Notice While installing the door station, make sure that the distance between any two devices is far enough to avoid the howling and echo. The distance between two devices is recommended to be longer than 10 meters.
Need help?
Do you have a question about the LTH-M001 and is the answer not in the manual?
Questions and answers