Four Seasons Courtyard 258728 Assembly Instructions

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Identify all parts packed in the carton against the parts list. Remove all protective materials.
Step 1:
Place parts on a non-abrasive surface to avoid scratching.
Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker
assembly is positioned all the way into the base. It may have shifted or vibrated out during
shipment.
Step 3: Important: We recommend 2 people work together to assemble the chair.
labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the rocker
plate. Point the open end of the horseshoe away from you. The arrows on the rocker
assembly should be pointing towards you. Set the chair frame on the rocker assembly with the
front of the seat facing you and the arrows on the "U" bar pointing towards you as shown in
Figure 1
. This is very important for a safe, balanced rocking motion.
been properly positioned on the rocker assembly, all arrows on the "U" bar and rocker
assembly will be pointing in the same direction.
Step 4: Critical Step: The "U" metal plates must be installed in the proper location.
Read this step and carefully examine.
rocker plate are between both sides of the "U" metal plate. Make sure that the holes in the
"U" metal plate are completely aligned with the holes in the "U" bar as shown in
Guide the bolts through the holes on the top side of the "U" metal plate, through the holes in
the "U" bar, through the holes in the rocker plate and then, most importantly, through the holes
in the bottom side of the "U" metal plate. It is very important that the holes in the bottom of
the "U" metal plate are placed directly beneath the holes in the rocker plate. Add a spring
washer and a nut to each bolt as shown in
only. Repeat the same procedure on the other side.
CAUTION: Failure to place the "U" metal plates under the rocker plates and
above the "U" bar exactly as shown in the diagram will cause the bolt heads and nuts
to damage the structure of the rocker plates and the "U" bar. Damage due to over
tightening of bolts or improper assembly could cause injury and may void your
warranty.
Step 5: Tighten all nuts and bolts with the hex wrenches provided.
Remove the arrow labels from the "U" bar and rocker assembly. Cover bolts with bolt covers.
Your chair should be ready for use. If your chair is not rocking properly, double-check your
Step 6:
assembly procedure, especially Steps 3-4. If the chair rocks too far forward to or is difficult
to rock backwards, you have probably installed the chair frame backwards on the rocker
assembly.
SKU #258728(ADT01901H60)
Note the arrow
If the chair frame has
Insert the "U" metal plate so that the "U" bar and
Figure 2
. Hand tighten nuts 2-3 revolutions
Bolts must be FULLY tightened.
Chair Viewed From The Front
A
Figure 2
.
B
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST DESCRIPTION
A
CHAIR FRAME
SWIVEL BASE &
B
ROCKER
ASSEMBLY
5/16" X 40 MM
C
BOLT
Ø 8.0 X 2.3 MM
D
SPRING WASHER
"U" METAL
E
PLATE
F
5/16" NUT
G
BOLT COVER
Page 2
Assembly detail shown from the REAR
of the chair for clarity
ROCKER PLATE
E
Figure 1
G
Figure 2
FOOT CAP
QTY
ORDER PART # PARTS LIST DESCRIPTION
AR20511 1
HEX WRENCH-1
1
AR20512
HEX WRENCH-2
ROCKER PLATE
HW0295 4
FACTORY ASSEMBLY
FOOT CAP
4
HW0003
FACTORY ASSEMBLY
4.8 X 25MM BOLT
HW0618 2
FOR FOOT CAP
FACTORY ASSEMBLY
SLING TUBE CAP
HW0015 4
FACTORY ASSEMBLY
HW0028 8
ROCKER
ASSEMBLY
"U" BAR
G
C
"U" BAR
D
F
QTY
ORDER PART #
HW0008 1
1 1
HW0007
G0228
FC0013
HW0695
FC0563