Table of Contents
Advertisement
Quick Links
Siena Twist
360° Car Seat
Instruction Manual
NOTICE
This is an "i-Size" Enhanced Child Restraint System.
This is an "i-Size" booster seat Enhanced Child Restraint System.
i-Size ISOFIX car seat suitable 40cm–150cm
Approved to Regulation No.129, for use in, "i-Size compatible" vehicle
seating positions as indicated by vehicle manufacturers in the vehicle
users' manual.
If in doubt, contact hello@amanababy.com.
DO NOT USE REARWARD FACING ECRS IN SEATING POSITIONS WHERE
THERE IS AN ACTIVE FRONTAL AIRBAG INSTALLED. UNIVERSAL Vehicle
ISOFIX Child Restraint Systems. IMPORTANT - DO NOT USE FORWARD
FACING BEFORE THE CHILD'S AGE EXCEEDS 15 months (Refer to
instructions).
Advertisement
Table of Contents
Related Manuals for Amana Siena Twist
Summary of Contents for Amana Siena Twist
- Page 1 Siena Twist 360° Car Seat Instruction Manual NOTICE This is an “i-Size” Enhanced Child Restraint System. This is an “i-Size” booster seat Enhanced Child Restraint System. i-Size ISOFIX car seat suitable 40cm–150cm Approved to Regulation No.129, for use in, “i-Size compatible” vehicle seating positions as indicated by vehicle manufacturers in the vehicle users’...
- Page 2 Instruction Manual Siena Twist 360° Car Seat...
- Page 3 Child height: 40–150cm Weight: 0–36kg Suitable age: Birth – approx. 12 Years Rearward facing 40–105cm: ISOFIX + Support leg + harness Forward facing 76–105cm: ISOFlX + Support leg + harness Forward facing 105–150cm: ISOFIX attachments + adult safety-belt or adult safety- belt only Please carefully read this manual and follow each step to ensure a comfortable travel and best protection for your child.
-
Page 4: Table Of Contents
Remove and assemble the fabric cover ........24 Siena Twist 360° Car Seat... -
Page 5: Structure
1. Structure 1. Handle of headrest 11. Adjuster button 2. Headrest 12. Angle adjuster 3. The guide groove of the headrest 13. Rotation adjuster 4. Rear cover board (instruction manual 14. Harness adjuster strap inside) 15. Support leg release button 5. -
Page 6: Precautions For Product Use
14. Ensure that any lap strap is worn low down, so that the pelvis is firmly engaged, shall be stressed. 15. DO NOT continue to use this car seat after it has suffered any violent crash. Replace immediately as there may be invisible structural damage from the crash. Siena Twist 360° Car Seat... - Page 7 16. It’s dangerous to make any alterations or additions to the device without the approval of the Type Approval Authority, also dangerous not to follow closely the installation instructions provided by the manufacturer. 17. When the chair is not provided with a textile cover, the chair should be kept away from sunlight, otherwise it may be too hot for the child’s skin.
-
Page 8: Safety Warning
76–105cm 105–150cm Rearward-facing position R Forward-facing position 123456 Forward-facing position 1 ISOFIX+ Support Leg ISOFIX+ Support Leg ISOFIX+ Adult Safety Belt Only This car seat conforms to National standard: GB27887- 2011 and European ECE R129/03 Siena Twist 360° Car Seat... -
Page 9: Use In The Vehicle
4. Use In The Vehicle 4.1 Install In The Car Correct Position Only suitable if the approved vehicles are fitted with 3 point Shoulder belt safety-belt, approved to UN/ ECE Regulation No.16 or other equivalent standards. Lap belt Proper installation Improper installation ISOFIX anchorages Not to be used in seating... -
Page 10: Checking The Shoulder Strap Height
At the same time, hearing “click” means the buckle gets stuck, pull the pieces of the buckle and check whether the buckle is locked correctly. • To release the safety belts, press the red button. Siena Twist 360° Car Seat... -
Page 11: Adjusting The Harness
4.5 Adjusting The Harness Loosen the harness g The harness can be slackened by pressing the adjuster (under the seat cover) on the front of the seat. Press down the adjuster as you grip the two harness with your another hand. Pull the harness towards you to loosen the harness. -
Page 12: Storing Shoulder Pads With Chest Pad And Buckle
5. Loosen the snap button on both sides of the headrest cover to expose the internal structure of the seat. 6. Store the sorted shoulder sleeves in the grooves inside the seat. Siena Twist 360° Car Seat... -
Page 13: Usage Of The Support Leg
4.7 Usage Of The Support Leg When child height in 40-105cm, the support leg is in the usage state. EXCLAMAT • Lift the bottom of the seat and push the support leg forward from the groove with your hand. • Push it to the front end and then take the support leg out, let it is perpendicular to the ground and hear a sound of... -
Page 14: Adjust The Isofix Attachments
• Push the red release button of the ISOFIX chuck at the direction as shown, the ISOFIX chuck will be released. After the ISOFIX chuck is installed, EXCLAMAT push the child restraint forwards until it is tight against the car seat. Now, the ISOFIX base is installed in place. Siena Twist 360° Car Seat... -
Page 15: Rotating The Car Seat
4.9 Rotating The Car Seat Find the rotation adjuster button f, lift up and rotate the body at the same time (both sides can be rotated). When you hear a sound of “click”, the rotation adjuster automatically retracts, indicating that the gear is in place. Forward-facing 90°... -
Page 16: Reclining The Car Seat
01 02 Rearward-facing Forward-facing 40–105cm 76–105cm, 9–18kg Weight: 0–18kg Adjust to Gear Effect after rotation 01/02/03/04/05/06 adjustment. 105–150cm, 15–36KG Adjust to Gear 01 Siena Twist 360° Car Seat... -
Page 17: Installation
5. Installation 5.1 Notice Before Installation Small Headrest Shoulder Pads / Buckle Height Triangle Sponge Crotch Pad & Cushion Straps (Sketch Map) 40–87cm 87–105cm 105–150cm... -
Page 18: Rearward-Facing Installation 40-105Cm
3. Push ISOFIX on both sides of the Remove base and clip it into the ISOFIX guide sleeve. When a “click” is heard, the ISOFIX release button k is displayed in green colour. Small Headrest +Cushion Triangle sponge Siena Twist 360° Car Seat... - Page 19 4. Press and hold the adjustment button on the support leg ; to adjust the length up and down until it contacts the vehicle ground, and the bottom of the support leg will be shown green. 5. Turn the rotation adjuster f to rotate the seat to the 90°...
-
Page 20: Forward-Facing Installation 76-105Cm
3. Push ISOFIX on both sides of the Remove base and clip it into the ISOFIX guide sleeve. When a “click” is heard, the ISOFIX release button k is displayed in green colour. Small Headrest +Cushion Triangle sponge Siena Twist 360° Car Seat... - Page 21 4. Press and hold the adjustment button on the support leg ; to adjust the length up and down until it contacts the vehicle ground, and the bottom of the support leg will be shown green. 5. Place the child in the safety seat, lock the buckle i, and tighten the front tether g.
-
Page 22: Forward-Facing Installation 105-150Cm Option 1
ISOFIX release button k Shoulder sleeves / Shoulder straps is displayed in green colour. See section 4.6 “Storing Shoulder Crotch pad Pads With Chest Pad And Buckle” on page 9 to remove the parts. Buckle Siena Twist 360° Car Seat... - Page 23 4. Put the child into the safety seat, adjust the headrest up and down according to the height of child. 5. Pull out the adult 3-point belt: D. Clip the vehicle shoulder belt into the belt guide hook Shoulder belt of the headrest, and then Lap belt clip vehicle shoulder and lap...
-
Page 24: Forward-Facing Installation 105-150Cm Option 2
See section 4.6 “Storing Shoulder Pads With Chest Pad And Buckle” on page 9 to remove the parts. 105-150CM Remove Shoulder sleeves / Shoulder straps Small Headrest +Cushion Crotch pad Triangle sponge Buckle Siena Twist 360° Car Seat... - Page 25 3. Pull out the adult 3-point belt: D. Clip the vehicle shoulder belt into the belt guide hook Shoulder belt of the headrest, and then Lap belt clip vehicle shoulder and lap belt together into the belt guide slot on the side of the seat, finally lock the buckle.
-
Page 26: Main Technical Parameters
Never use any solvent, chemical detergent or lubricant on any part of your EXCLAMAT car seat. 30° Hand wash, water Do not bleach Dry clean, any Do not tumble dry Do not iron temperature solvent except below 30°C trichloroethylene Siena Twist 360° Car Seat... -
Page 27: Remove And Assemble The Fabric Cover
7.3 Remove and assemble the fabric cover Disassembly Steps: Remove the Take off the Take off the button first cushion triangle sponge Open both Remove the cover Finally, remove the shoulder sleeves on the headrest cloth cover along the edge of the seat... - Page 28 hello@amanababy.com Imported by Millsons of London Ltd. EC1V 2NX Made in China...
Need help?
Do you have a question about the Siena Twist and is the answer not in the manual?
Questions and answers
Baby is approx 75cm and does not fit in the car seat with the newborn insert - head rest part below shoulders and difficult to sit. Can it be removed? States should have until approx 87cm.
Yes, the newborn insert can be removed from the Amana Siena Twist car seat for a baby approximately 75cm tall. The rearward-facing usage is specified for 40–105cm, and inserts like the newborn cushion are typically used for smaller babies. At 75cm, the baby has likely outgrown the need for the newborn insert.
This answer is automatically generated