Subscribe to Our Youtube Channel
Related Manuals for Lippert LEWMAR 2023012930
Summary of Contents for Lippert LEWMAR 2023012930
- Page 1 Pontoon Deck Mounting Bracket for Shallow Water Anchors Installation Guide REV: 08.08.2024 CCD-0008071...
- Page 2 Parts List CCD-0008071 REV: 08.08.2024 Page 2...
- Page 3 Pontoon Deck Mounting Kit, Black—2024028463 Letter Part Description Qty. 2023012930 Pontoon Deck Mounting Bracket, Black 2023045514 Backing Plate, Black 2024029943 Bolt, 3/8”-16 x 5”, Hex HD, SS 2023015252 Washer, 3/8” ID x 1” OD, SS 2023015228 Nut, Brass, 3/8”-16 2023017309 SWA Mounting Kit 2023015256 Bolt, 3/8”-16 x 2”, Hex HD, SS...
- Page 4 Parts List CCD-0008071 REV: 08.08.2024 Page 4...
- Page 5 Pontoon Deck Mounting Kit, White—2024028466 Letter Part Description Qty. 2023017454 Pontoon Deck Mounting Bracket, White 2024028163 Backing Plate, White 2024029943 Bolt, 3/8”-16 x 5”, Hex HD, SS 2023015252 Washer, 3/8” ID x 1” OD, SS 2023015228 Nut, Brass, 3/8”-16 2023017309 SWA Mounting Kit 2023015256 Bolt, 3/8”-16 x 2”, Hex HD, SS...
-
Page 6: Resources Required
Resources Required 9/16” ∆ ∆ Torque wrench, 0-100 ft-lbs wrench 9/16” ∆ ∆ Pencil or non-permanent marker socket with ratchet ∆ 3/8” Cut-off wheel or reciprocating saw ∆ drill bit ∆ Corded or cordless drill Preparation 1. Place the pontoon mounting bracket (Fig. 1A) on the rear deck (Fig. 1B) directly above a pontoon tube (port or starboard) (Fig. - Page 7 Fig. 1 CCD-0008071 REV: 08.08.2024 Page 7...
- Page 8 Fig. 2 3. Carefully inspect the mounting location before drilling. A. If possible, pontoon mounting holes should pass through the port-to-starboard stringers (Fig. 3A). B. Use the included backing plates (Figs. 3 and 4) for added support. CCD-0008071 REV: 08.08.2024 Page 8...
- Page 9 stringer outer frame stringer backing plates Fig. 3 CCD-0008071 REV: 08.08.2024 Page 9...
- Page 10 no stringer outer frame stringer backing plates Fig. 4 CCD-0008071 REV: 08.08.2024 Page 10...
-
Page 11: Installation
4. Mark the four mounting bracket slot locations (Fig. 2A). 5. Use a 3/8” drill bit to drill four through-holes through the deck and stringers such that the through-holes align along the center of the stringer’s width and close to the center of the mounting bracket’s slots. - Page 12 4. Torque all nuts to 45 ft-lbs. 5. If there is an excess length of bolt thread beyond the 3/8” nylon locking nut, the excess may be cut off if so desired. Fig. 6 CCD-0008071 REV: 08.08.2024 Page 12...
- Page 13 Mounting Through Deck 1. Use the 5” bolts and backing plates to secure the pontoon bracket to the deck. 3/8” 3/8” A. Place a washer (Fig. 7A) onto each -16 x 5” bolt (Fig. 7B). B. Install assembled bolts through the mounting bracket, pontoon deck and stringer (if applicable) (Fig.
- Page 14 C. Place a ” washers backing plate (Fig. 8A) over each pair of bolts followed by (Fig. 8B) onto each bolt then secure with threading on a ” nylon locking nut (Fig. 8C). NOTE: When using a backing plate, the plate MUST be sandwiched between the pontoon deck and the second washer.
- Page 15 Mount Anchor to Adapter Plate 1. Align the holes of the anchor’s mounting bracket with the holes of the Pontoon Deck Mounting Bracket. 2. Use the supplied SWA Mounting Kit (P/N 2023017309) to mount the anchor to the Pontoon Deck Mounting Bracket (Fig. 9). Fig.
- Page 16 3. Mounting a Second Anchor If installing a second Pontoon Deck Mounting Bracket, repeat Preparation and Installation instructions. NOTE: A second, separate Pontoon Deck Mounting Bracket kit is required. Fig. 10 CCD-0008071 REV: 08.08.2024 Page 16...
-
Page 17: Care And Maintenance
CARE AND MAINTENANCE When preparing to trailer or store the boat, take precautions to protect the anchor(s) from possible damage. 1. Make sure the anchor is fully retracted. 2. Periodically inspect the Pontoon Deck Mounting Bracket and, if applicable, the backing plate(s), wire harnesses and electrical connections for damage or loose or missing parts. - Page 18 T: 432-LIPPERT (432-547-7378) Email: techsupport@lewmar.com Email: customerservice@lci1.com The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized Lippert representative has been provided.
Need help?
Do you have a question about the LEWMAR 2023012930 and is the answer not in the manual?
Questions and answers