Denon AVR-990 Owner's Manual page 11

Setting items
Channel Level Test Tone Start : Output test tone.
• Front L / Front Height L / Center / Front Height R / Front R / Front
Set the volume of the test
Wide R / Surround R / S. Back R z / S. Back L z / Surround L / Front
tone to be the same when it
Wide L / Subwoofer : Select the speaker.
is output from each speaker.
z : W hen the "Speaker Configuration" – "Surround Back" setting
(vpage 9) is set to "1spkr", "S. Back" is displayed.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
• S peakers set to "None" in the "Speaker Configuration" (vpage 8)
settings are not displayed.
• W hen o is pressed while the subwoofer volume is set to "–12 dB", the
"Subwoofer" setting switches to "OFF".
• W hen a headphones jack is inserted in the PHONES terminal of the AVR-
990, the "Channel Level" is not displayed.
• Y ou can also press
original versionH Operating Instructions "Adjust the Volume of the
Different Speakers").
Default : Reset all channel level settings to factory default.
• Y es : Reset to the defaults.
• No : Do not reset to the defaults.
Crossover Frequency 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Outputs at below set
frequency, each speaker's
Advanced : Specify crossover frequency for each speaker.
bass signal output from
• Front / Center / Surround / Surround Back / Front Height / Front
the subwoofer. Set this
Wide : Select the speaker.
according to the low
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
frequency reproduction
250Hz : Set the crossover frequency.
capabilities of the speakers
you are using.
• Can be set when the "Speaker Configuration" – "Subwoofer" (vpage
8) setting is "Yes", or when you have a speaker that is set to "Small".
• Always set the crossover frequency to "80 Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
• The speakers that can be set when "Advanced" is selected differ
according to the "Subwoofer Mode" setting (vpage 9).
• W hen "LFE" is selected, speakers set to "Small" at "Speaker
Configuration" can be set. If the speakers are set to "Large", "Full
Band" is displayed and the setting cannot be made.
• I f set to "LFE+Main", this setting can be made regardless of the
speaker size.
Main remote control
operation buttons
Setting contents
[CHANNEL LEVEL]
to set (vpage 77 of GThe
:Displaying the menu :Moves the cursor
Cancel the menu (Up/Down/Left/Right)
Setting items
Front Speaker Setup Setting : Choose the method for setting the front speakers.
• Normal : The front speakers are set using the
Set the front speakers to
• Custom : The front speakers used for the different playing modes are
use for every surround
set in advance.
mode.
2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
pure direct play modes (2 channel) are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
MULTI CH : The front speakers used in modes other than the direct,
stereo and pure direct play modes (2 channel) are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
NOTE
• When set to "Custom",
• The front speaker setting stored for the "Quick Select" function is given
priority.
:Confirm the setting
ENGLISH
Making Detailed Settings (Manual Setup)
Setting contents
<FRONT SPEAKERS>
.
<FRONT SPEAKERS>
does not operate.
0
:Return to previous menu