Related Manuals for Range Road RR503
Summary of Contents for Range Road RR503
- Page 1 Range Road RR503 Standalone Conveyor Owner’s Manual Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 2 DO NOT use the product until you have first contacted us to determine if it can or should be performed on the product. For technical questions please visit www.range-road.ca or www.range-road.com. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
-
Page 3: General Safety Rules
Be alert to your surroundings. Using a machine in confined work areas may put you dangerously close to rotating parts. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1... -
Page 4: Stay Alert
Store idle conveyor. When conveyor is not in use, store it in a secure place out of the reach of children. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca... -
Page 5: Important Safety Information
Use only lubricants and fuel recommended in the engine manual or in the Specifications Chart of this manual. CARBON MONOXIDE HAZARD !!! Using an engine indoors CAN KILL YOU IN MINUTES. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca... - Page 6 3. Wear ANSI-approved safety glasses, hearing protection, and NIOSH-approved dust mask/respirator under a full face shield during use. Wearing steel toe shoes is also recommended. 4. Wear heavy-duty work gloves when handling the blades. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1...
- Page 7 6. Use only accessories that are recommended by Range Road for your model. Accessories that may be suitable for one piece of equipment may become hazardous when used on another piece of equipment.
-
Page 8: Service Precautions
Wear approved safety goggles, heavy-duty gloves, and a dust mask/respirator during service. Maintain all labels on the saw mill. These show important information. If unreadable, missing or damaged, contact Range Road for a replacement. Have the equipment serviced by a qualified repair person using only OEM replacement parts. - Page 9 It is best to pull the components out of the crate and lay them out so you can access them as needed. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 10 4 bolts. Take out the 4 bolts of this frame section. Put the 2 frame parts together and insert 4 bolts. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1...
- Page 11 Tighten the swivel bolt until there is no up and down movement in the axle stub, but the axle stub must be able to move freely from side to side. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 12 Put in the cotter pin and bend it so it will not interfere with the cap. Install the hub caps. Assembly should now look like this. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 13 13mm nuts. Once all 4 – 13mm nuts are threaded on, tighten them securing the engine into place. Find the exhaust protector bracket. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 14 Install the exhaust protector bracket. Remove these 6 bolts. Install the hydraulic tank. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 15 The 2 bolts must be loose enough so that the frame can move up and down without binding. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 16 Remove the caps from the cylinder. Install the cylinder. Install the 2 frame brackets. One on each side. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 17 7 - 16mm bolts x 17mm nuts, Place the 2 sections together, re-install the 7 bolts and nuts through the 2 sections and tighten. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 18 Set the conveyor trough in place on the frame. Find the 2 bolts with the square head. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 19 Set the last conveyor trough section in place, upside down. Insert the bolts and tighten, leave some looseness so the sections can swivel. Find the conveyor motor. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 20 Install the motor. Tighten the 16mm Bolt x 17mm nut, tighten both allen keys on the coupler. Insert the control T-Handle. Install the control valve, the levers and tighten the lock nuts. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 21 Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1...
- Page 22 Install the suction hose between the tank and pump. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 23 Install the pressure hose from the pump to the control valve. Plug the conveyor motor hoses into the control valve using the quick connect fittings. Install the motor hoses to the motor. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 24 Tighten the 10mm nut and bolt, leave it loose enough that the roller can still slide when adjusting it. Mount the 2 upper side extensions and tighten. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 25 Fit the last 3 plates to the conveyor where the hydraulic motor is located. Chain can now be installed. It is easier to install the chain if the conveyor is raised Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 26 – position and slowly open it until it moves at the speed you are comfortable with. Raise the conveyor and install the chain. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
- Page 27 Adjust both chain tensioner. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
-
Page 28: Start Procedure
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING: Turn the power Switch of the equipment to its “OFF” position and wait for the engine to cool before performing any inspection, maintenance or cleaning procedures. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1... -
Page 29: Maintenance Procedures
5. For cold weather operation, store the equipment in a cool dry area to prevent condensation and premature wear. Equipment Troubleshooting Follow all safety precautions whenever diagnosing or servicing the equipment or engine. Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca... -
Page 30: Please Read The Following Carefully
Note: Some parts are listed and shown for illustration purposed only, and are not available individually as replacement parts. WARRANTY One-year limited warranty For technical questions, please visit www.range-road.ca www.range-road.com Range Road Enterprises Ltd Box 5 Site 9 RR1 Lacombe, AB T4L2N1 www.range-road.ca...
Need help?
Do you have a question about the RR503 and is the answer not in the manual?
Questions and answers