Related Manuals for CONQUEST MMG
Summary of Contents for CONQUEST MMG
- Page 1 CONQUEST MMG FLOOR SCRUBBER OPERATOR MANUAL T: 1800 826 789 E: support@conquestequipment.com.au W: conquestequipment.com.au...
- Page 2 Scan QR code to access your MMG Floor Scrubber Operator video...
-
Page 3: Main Machine Components
MAIN MACHINE COMPONENTS The machine's main components are the following: Operator seat Recovery tank lid. Lateral scrubbing brush head (optional). Recovery tank. Scrubbing brush head. Solution tank. Squeegee body. Right hatch. Hour meter display – battery charge level. Left hatch. Headlights (optional). -
Page 4: Table Of Contents
CONTENTS MAIN MACHINE COMPONENTS .......... 3 7. CLEANING THE LATERAL BRUSH (SWEEPING VERSION) .. 21 CONTENTS ................4 8. CLEANING THE RECOVERY TANK FILTERS ......21 1. GENERAL SAFETY REGULATIONS ........ 5 9. CLEANING THE RECOVERY TANK......... 21 10. CLEANING THE DEBRIS HOPPER (SWEEPING VERSION) 21 1. -
Page 5: General Safety Regulations
1. GENERAL SAFETY REGULATIONS The following symbols are used to indicate any potentially hazardous situations. Always read this information carefully and take the necessary precautions to protect any people and/or objects that may be present. Operator cooperation is paramount for accident prevention. No accident prevention programme can be effective without the full cooperation of the person directly responsible for the machine's operation. -
Page 6: Using The Machine
2. USING THE MACHINE DANGER: • In the event of danger, quickly press the emergency button in the electrical system panel near the operator's seat. • Never collect gases, explosive/inflammable liquids or powders, nor acids and solvents! These include gasoline, paint thinners and fuel oil (which, when mixed with the vacuum air, can form explosive vapours or mixtures), and also non-diluted acids and solvents, acetones, aluminium and magnesium powders. - Page 7 • The machine does not cause harmful vibrations. • Use the machine only in the way described in this manual. • Do not pick up anything that is burning or smouldering, like cigarettes, matches or glowing embers. • Reduce speed on slopes and dangerous corners. •...
-
Page 8: Deactivation Of The Machine
3. DEACTIVATION OF THE MACHINE WARNING: • Always protect the machine against sunlight, rain, and other atmospheric agents, both while it is stationary and while it is in function. Store the machine in a dry, sheltered place: this machine is only designed for use under dry conditions, and must not be used or stored outdoors under humid conditions. -
Page 9: Transport
• If any issues are encountered while using the machine, check to make sure that these are not due to a lack of proper maintenance. Otherwise, request the intervention of authorized personnel or an Authorized service centre. • If any parts need to be replaced, always request ORIGINAL spare parts from an authorized Dealer or Retailer. - Page 10 ATTENTION: • The machine must only be stored under temperature conditions ranging from 0 °C to +40 °C. The humidity level must be between 30% and 95%.
-
Page 11: Symbols Used In The Manual
9. TECHNICAL DESCRIPTION Information symbol: The MMg Base is a floor scrubbing machine that's capable of handling a wide variety of floors and Indicates additional information for the operator, to improve the use of the device. types of dirt thanks to the mechanical action of two or three brushes and the chemical action of a water- detergent solution. -
Page 12: Technical Data
13. TECHNICAL DATA TECHNICAL DATA MMg 1SL [KMS] Cylindrical Orbital Rated machine power 2025 2140 2090 2090 Working capacity up to sq.m./h 4000 4500 5000 4500 Working width Working width with the lateral brush Squeegee width Central brush head brushes (number -Ø external bristles) No. -
Page 13: Symbols Used On The Machine
14. SYMBOLS USED ON THE MACHINE Main switch symbol: Warning label (versions without built-in battery charger): Applied to the control panel, positioned on the front of the machine, to Affixed to the machine in order to warn the operator to read the user and indicate the main switch. -
Page 14: Machine Preparation
15. Press the drive pedal (7) (Fig.10) to begin moving the machine. 16. MACHINE PREPARATION 16. Drive the machine down the ramp. 1. HANDLING THE PACKAGED MACHINE ATTENTION: during this operation, check there are no people or objects near the machine. The machine's overall weight including packaging is 300Kg. -
Page 15: Securing The Machine
4. SECURING THE MACHINE CAUTION: the lifting hooks must not damage the blocks, connectors or cables. The procedure for securing the machine, thus allowing the operations to be performed under conditions of complete safety, is as follows: NOTE: before inserting the batteries, remember to cover the terminals with a little grease to protect them against external corrosion. -
Page 16: Assembling The Squeegee Body
NOTE: carefully read the use and maintenance instructions of the battery charger that is used for charging. Remove the cap (4) from the battery charger socket (Fig.4). CAUTION: before connecting the batteries to the battery charger, make sure it is suitable for the batteries used. -
Page 17: Scrubbing Without Drying
The appliance will now begin to work with full efficiency until the battery is flat or until the detergent solution has finished. During the first few metres, check that there is sufficient solution. NOTE: If the drive pedal is released during the scrubbing without drying operation, the brush motor and the solenoid valve will be deactivated. -
Page 18: Reverse Gear
5. REVERSE GEAR 9. EMERGENCY BUTTON This machine is equipped with electronic traction control. To reverse, proceed as follows: If any problems are encountered during the work operations, press the emergency button (1) on the electrical system's cover carter (Fig.1). 1. -
Page 19: Lateral Brush 2Sl (Sweeping Version)
19. AT THE END OF THE WORK 13. LATERAL BRUSH 2SL (SWEEPING VERSION) If the lateral brushes need to be used during the floor scrubbing operations, and therefore with the At the end of the work, and before carrying out any type of maintenance, perform the following brush head in its working position, press the lateral brush head activation/deactivation button (1) on the operations: left-hand side of the steering column (Fig.1). -
Page 20: Emptying The Recovery Tank
1. EMPTYING THE RECOVERY TANK Proceed as follows to empty the recovery tank: 1. Take the machine to the maintenance area. 2. Make sure the machine has been secured (see the section titled “SECURING THE MACHINE”). CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious injury to hands. -
Page 21: Cleaning The Lateral Brush (Scrubbing Version)
6. Clean the basket/filter (2) and the basket cover (3) under a jet of water. 6. CLEANING THE LATERAL BRUSH (SCRUBBING VERSION) NOTE: Use a spatula or brush to eliminate any dirt that is particularly difficult to remove. Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush head gearmotor lifespan. -
Page 22: Emptying The Solution Tank
11. EMPTYING THE SOLUTION TANK 12. CLEANING THE WATER SYSTEM FILTER Proceed as follows to empty the solution tank: In order to clean the water system's filter, do the following: 1. Take the machine to the maintenance area. 1. Take the machine to the maintenance area. 2. -
Page 23: Extraordinary Maintenance Work
6. With the brush head in its resting position, turn the knobs (4) that hold the left lateral carter (5) in 21. EXTRAORDINARY MAINTENANCE WORK place anti-clockwise (Fig.4). 7. Remove the left lateral carter (5) (Fig.5). 1. ASSEMBLING THE BRUSH HEAD BRUSHES (SCRUBBING VERSION) 8. -
Page 24: Replacing The Brush Head Brushes (Sweeping Version)
6. REPLACING THE BRUSH HEAD BRUSHES (SWEEPING VERSION) 9. REPLACING THE ABRASIVE PAD (ORBITAL VERSION) Ensuring the integrity of the brush will guarantee better floor cleaning results, and will extend the service Ensuring the good condition of the abrasive pad will guarantee better floor cleaning results, and will life of the brush head's gearmotor. -
Page 25: Adjustment Interventions
(1) a quarter turn clockwise (Fig.1). mod. MMg base CB - MMg base 1SL CB - MMg cylindrical CB - MMg orbital CB 3. Turn the squeegee control lever (2) anti-clockwise (Fig.2) to bring the squeegee body to its working position. -
Page 26: Troubleshooting
25. TROUBLESHOOTING This chapter lists the most common problems linked with the use of the machine. If you are unable to resolve the problems with the information given here, please contact your nearest assistance centre. PROBLEM POSSIBLE CAUSE SOLUTION The main switch is set to “0”. Make sure that the main switch is in its "I"... - Page 27 NOTE...
- Page 28 NOTE...
Need help?
Do you have a question about the MMG and is the answer not in the manual?
Questions and answers