Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for holzkraft BTS 200
Summary of Contents for holzkraft BTS 200
- Page 1 Operating Instructions Belt and Plate Sanding Machine BTS 200 BTS 200...
-
Page 2: Table Of Contents
12.3 Disposal of lubricants........15 12.4 Disposal via municipal collection points..16 13 Spare parts .......... 16 13.1 Spare parts drawing........17 14 Circuit diagram........20 15 EC Declaration of Conformity .... 21 16 Notes ............ 22 BTS 200 | Version 3.04... -
Page 3: Introduction
You have made a good choice by purchasing the Belt even further. and Disc Grinding Machine made by HOLZKRAFT. 1.3 Limitation of liability Thoroughly read the operating instructions before commissioning the machine. -
Page 4: Obligations Of The Operating Company
BTS 200 | Version 3.04... -
Page 5: Qualification Of Personnel
Safety data sheets for hazardous materials can be obtai- ned from your specialist dealer or by phone: +49 (0)951/ 96555-0. Specialist dealers can find safety data sheets in the download area of the partner portal. BTS 200 | Version 3.04... -
Page 6: General Safety Instructions
- Do not use compressed air to clean the machine or to remove chips. - All protective and safety devices must be refitted immediately after repair or maintenance has been completed. BTS 200 | Version 3.04... -
Page 7: Residual Risks
- Risk of injury to the eye from flying parts, even with protective goggles. Technical data Model BTS 200 Motor power (230 V/50 Hz) 1,1 kW Fig. 1: Type plate BTS 200 Motor speed 1720 min-1 Belt speed 12 m/sec. Transport, packaging, storage Grinding disc-Ø... -
Page 8: Packaging
When transporting, act responsibly and always consider the consequences. Refrain from daring and risky actions. Slopes and inclines (e.g. driveways, ramps and similar) are particularly dangerous. If driving on such passages is unavoidable, special care must be taken. BTS 200 | Version 3.04... -
Page 9: Description Of The Device
7.1 Installation The illustrations in these operating instructions serve the general comprehension and may deviate from the actual type. Fig. 3: Machine parts of Sanding Machine BTS 200 A Machine (Motor, workpiece support and chassis) B Grinding arm C Bearings cover... - Page 10 Step 4: Fasten the cover under the grinding arm with the 4 M6x10mm provided screws (fig. 8). Fig. 13: Fastening of the work table Fig. 9: Mount the cover of the tension pulley and sanding belt BTS 200 | Version 3.04...
-
Page 11: Put Up
Step 1: Open the side flap of the sanding arm cover and and the mode of operation of the machine. loose the tension of sanding belt with the tension lever (Fig. 16). Tips and recommendations Observe the running direction of the sanding belt. BTS 200 | Version 3.04... -
Page 12: Sanding Belt Run
The suction device must be switched on and off with the engine simultaneously or prompt. Step 1: Connect the suction hoses (Diameter 63 mm) with the connecting branch for the suction device and fix them with hose clamps. BTS 200 | Version 3.04... -
Page 13: Electrical Connection
The mains plug must be disconnected before carrying out any adjustment work on the machine. Remove the tension roller coverage to grind curved workpieces. Use ear protection! Use protective glasses! Use protective gloves! Fig. 20: Grinding of curved workpieces BTS 200 | Version 3.04... -
Page 14: Grinding At The Grinding Disc
10.2.4 Moving parts and lead to injury. All moving parts must be cleaned after 500 hours of op- eration using a soft brush. Then apply a thin layer of oil or grease to the moving parts. BTS 200 | Version 3.04... -
Page 15: Troubleshooting
Step 2: If required, disassemble the machine into easy- to-handle and usable components and parts. Step 3: Supply the machine components and operating materials to the provided disposal routes. BTS 200 | Version 3.04... -
Page 16: Disposal Via Municipal Collection Points
The drive roller for the Belt and plate sanding machine point for the recycling of electrical and electronic equip- BTS 200 must be ordered. The drive roller has the num- ment. By helping to properly dispose of this product, you ber 17 in the spare parts drawing 1. -
Page 17: Spare Parts Drawing
In case of service, the following drawing shall help to identify the necessary spare parts. Send a copy of parts drawing with the marked components to your authorised dealer when ordering spare parts. Fig. 21: Spare parts drawing BTS 200 BTS 200 | Version 3.04... - Page 18 Pan. head screw* M6x20 Ball bearing Pointer Platen table stop Screw* 6x10 Platen cover Push back spring Idler roller cover Push back spring Handle Screw* M8x50 Fixing plate Nut* Graphite paper Nut* Sanding paper Screw* M6x10 BTS 200 | Version 3.04...
- Page 19 22mm Hexagon wrench* 10-13mm Hexagon wrench* Hexagon wrench* Hexagon wrench* Round head M5x8 screw* Hexagon head M6x10 screw* Switch tempera- ture monitoring Washer* 6.5x16x2 Hexagon head M6x30 screw* * Standard part, available from specialist retailers BTS 200 | Version 3.04...
-
Page 20: Circuit Diagram
Circuit diagram 14 Circuit diagram Fig. 22: Circuit diagram BTS 200 | Version 3.04... -
Page 21: Ec Declaration Of Conformity
DIN EN ISO 12100: 2011 Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) Responsible for documentation: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 26.05.2021 ______________________ Kilian Stürmer General Manager BTS 200 | Version 3.04... -
Page 22: Notes
www.holzkraft.de...
Need help?
Do you have a question about the BTS 200 and is the answer not in the manual?
Questions and answers