Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for holzkraft TS 301
Summary of Contents for holzkraft TS 301
- Page 1 Instruction Manual Disc sander TS 301 TS 301...
-
Page 2: Table Of Contents
11.2 Disposal of electrical appliances..... 13 11.3 Disposal of lubricants........14 11.4 Disposal via municipal collection points..14 12 Spare parts..........14 12.1 Ordering spare parts........14 12.2 Spare parts drawing TS 301......15 13 Wiring Diagram........16 14 EC-Declaration of Conformity....17 TS 301 | Version 1.06... -
Page 3: Introduction
Introduction 1.3 Limitation of liability All information and notes in these operating instructions With the purchase of the disc sander from HOLZKRAFT were summarised taking the applicable standards and you have made a good choice. rules, the state-of-the-art and our long-term knowledge and experiences into consideration. -
Page 4: Obligations Of The Operating Company
She must implement these in form of operating manuals for the operation machine. TS 301 | Version 1.06... -
Page 5: Personal Protective Equipment
Breathing protection is used to protect the respira- recognized and understood at first glance, until new la- tory tract and lungs against the absorption of dust bels are attached. particles. TS 301 | Version 1.06... -
Page 6: Safety Data Sheets
Intended Use 3.3 Electrical Connection The disc sander TS 301 is used exclusively for sanding Danger! wood and wood-like materials (wood fiber board, chip- Danger to life due to electric shock! board, plywood boards, laminated and non-laminated boards, etc.). -
Page 7: Technical Data
The removal of danger Fig. 2: Type plate spots, disturbances and unevenness at the time of trans- port by other employees leads to considerable dangers. Careful planning of internal transport is therefore essen- tial. TS 301 | Version 1.06... -
Page 8: Packaging
- The disc sander may only be operated by a trained and experienced person. Fig. 3: Disc sander TS 301 - The operator may not work while under the influ- 1 Sanding disc with grinding wheel ence of alcohol, drugs or medication. -
Page 9: Assembly
Only if all parts are in order, the disc Step 5: Additionally tighten the clamping and guide grinder may be put into operation. [In case of ob- vious errors, contact a specialist or your dealer.] screw after every angle adjustment of the table. TS 301 | Version 1.06... -
Page 10: Adjusting The Miter Angle On The Work Table
Fig. 9: Open the dust cover Step 5: Remove the used grinding wheel from the san- ding pad. Clean the sanding pad from the glue residue and other contaminants. Use a suitable solvent, for example nitro diluent, for removal. TS 301 | Version 1.06... -
Page 11: Connection To An Extraction System
To replace the aluminum pad, hold the motor shaft with a wrench and turn the plate in the opposite direc- tion so that the pad can be removed from the motor shaft. Wear safety shoes! Wear protective clothing! TS 301 | Version 1.06... -
Page 12: Care, Maintenance And Repair
Step 2: Check if the worktable is tight. cloth. Step 3: Check that the correct sanding pad is mounted with the right grain size. Step 4: Connect suction system and start. TS 301 | Version 1.06... -
Page 13: Maintenance And Repair
For preparation for commisioning please contact a com- pany specialized for disposal. Step 1: Remove all environmentally hazardous fluids from the old device. Step 2: If necessary, dismantle the machine into mana- geable and usable assemblies and compo- nents. TS 301 | Version 1.06... -
Page 14: Disposal Of Lubricants
Example nicipal waste management, or the shop where you pur- chased the product. The engine for the Disc sander TS 301 must be ordered. The engine has the number 48 in the spare parts dra- wing 1. 12 Spare parts... -
Page 15: Spare Parts Drawing Ts 301
The following drawing is intended to help in case of service, to identify necessary spare parts. To order send a copy of the parts drawing with marked components to your dealer. Fig. 13: Spare parts drawing Disc sander TS 301 TS 301 | Version 1.06... -
Page 16: Wiring Diagram
Wiring Diagram 13 Wiring Diagram Fig. 14: Wiring Diagram Disc sander TS 301 TS 301 | Version 1.06... -
Page 17: Ec-Declaration Of Conformity
DIN EN ISO 12100:2011-03 Safety of machinery. General principles for design Risk assessment and risk reduktion Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 25.05.2021 ______________________ Kilian Stürmer Manager TS 301 | Version 1.06... - Page 18 www.holzkraft.de...
Need help?
Do you have a question about the TS 301 and is the answer not in the manual?
Questions and answers