Advertisement
Quick Links
PROGRAMMING
GAS CONTINUOUS FLOW - M SERIES
M Series Gas Continuous Flow Programming Parameter Settings
M20 (Natural Gas)
Min Gas Dynamic Pressure*
FA (Gas code)
Fb (50C/70C)
PH (Max TPP)
PL (Min TPP)
DH (Ignition pressure)
FH (Max fan speed)
FL (Min fan speed)
NE
FC
QU
M26 (Natural Gas)
Min Gas Dynamic Pressure*
FA (Gas code)
Fb (50C/70C)
PH (Max TPP)
PL (Min TPP)
DH (Ignition pressure)
FH (Max fan speed)
FL (Min fan speed)
NE
FC
QU
M20 (Propane - LPG)
Min Gas Dynamic Pressure*
FA (Gas code)
Fb (50C/70C)
PH (Max TPP)
PL (Min TPP)
DH (Ignition pressure)
FH (Max fan speed)
FL (Min fan speed)
NE
FC
QU
*Dynamic Pressure = Gas supply pressure when unit is running
1.13kpa
720Pa ±20Pa(8b)
960Pa ±20Pa(8b)
100 Pa ±20Pa(2b)
120 Pa ±20Pa(2b)
400 Pa ±20Pa(5A)
1.13kpa
800Pa ±20Pa(A5)
730Pa ±20Pa(A5)
120 Pa ±20Pa(30)
120 Pa ±20Pa(30)
350 Pa ±20Pa(5E)
350 Pa ±20Pa(5E)
2.75kpa
2
OF/ON
1880Pa ±20Pa(dC)
150Pa ±20Pa(22)
650 Pa ±20Pa(71)
65 r (C1)
26r (3E)
OF
OF
Save & exit
2.0kpa
3.0kpa
3
OF/ON
940Pa ±20Pa(8b)
120 Pa ±20Pa(2b)
62 r (B3)
34 r (5B)
OF
OF
Save & exit
2.0kpa
3.0kpa
6
OF/ON
715Pa ±20Pa(A5)
120 Pa ±20Pa(30)
350 Pa ±20Pa(5E)
65 r (D6)
24 r (4 a)
OF
OF
Save & exit
M26 (Propane - LPG)
Min Gas Dynamic Pressure*
FA (Gas code)
Fb (50C/70C)
PH (Max TPP)
PL (Min TPP)
DH (Ignition pressure)
FH (Max fan speed)
FL (Min fan speed)
NE
FC
QU
M Series Gas Continuous Flow - System Programming - Page 1
2.75kpa
5
OF/ON
1530Pa ±20Pa(DA)
140 Pa ±20Pa(23)
480 Pa ±20Pa(5D)
62 r (D0)
18 r (3E)
OF
OF
Save & exit
Advertisement
Related Manuals for chromagen M Series
Summary of Contents for chromagen M Series
- Page 1 FL (Min fan speed) 26r (3E) FL (Min fan speed) 18 r (3E) Save & exit Save & exit *Dynamic Pressure = Gas supply pressure when unit is running M Series Gas Continuous Flow - System Programming - Page 1...
-
Page 2: Entering Program Mode
Select UP to set unit to 70°C (On) Select by pressing ON / OFF Select DOWN to set unit to 50°C (Off) (Note: this change is not confirmed until you have saved and quit) M Series Gas Continuous Flow - System Programming - Page 2... - Page 3 (Refer to PL value in table) Select by pressing ON / OFF (Note: this change is not confirmed until you have saved and quit) M Series Gas Continuous Flow - System Programming - Page 3...
- Page 4 Select UP / DOWN to set the correct Select ON/OFF to confirm fan speed (Refer to FH value in table) (Note: this change is not confirmed until you have saved and quit) M Series Gas Continuous Flow - System Programming - Page 4...
- Page 5 Gas Pressure Test Points Digital Digital Manometer Manometer 2.920 0.100 Test Point Pressure Location ZERO ZERO ON/OFF ON/OFF Remote controller terminal ON SAB Test Here for incoming Gas pressure M Series Gas Continuous Flow - System Programming - Page 5...
Need help?
Do you have a question about the M Series and is the answer not in the manual?
Questions and answers