Service PMD660 / F2B/N2B/U2B Manual Solid State Recorder TABLE OF CONTENTS SECTION PAGE 1. TECHNICAL SPECIFICATIONS ....................1 2. SERVICE MODE........................... 2 3. HOW TO DISASSEMBLE......................3 4. MAIN MICROPROCESSOR (Q120) UPDATE PROCEDURE ............8 5. WIRING DIAGRAM ........................11 6.
Page 2
The exchange of the lithium battery(Z001 : CR2025). (Z001 : CR2025) CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SHOCK, FIRE HAZARD SERVICE TEST : CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and controls and chassis bottom.
1. TECHNICAL SPECIFICATIONS Digital audio system General System ..........Solid State Recorder Headphone output power ......8 mW/ 16 ohms Usable media ........... CF memory cards Speaker output power ........150 mW/ 8 ohms Microdrive Phantom power ...........+48V, 5mA Recording and media methods Power consumption .mp3 ........
2. SERVICE MODE 2. SERVICE 1. Micro-Processor(Q120) VERSION 1. Micro-Processor(Q120) Version check 1) Slide POWER switch to turn on the unit. 1) POWER 2) MENU/STORE/EDIT 2) Press MENU/STORE/EDIT button. 3) DISPLAY Preset-1 3) Preset-1 is displayed on LCD. MARK S.SKIP IN - STEREO 44.1K...
3. HOW TO DISASSEMBLE 1) Remove 6 screws of the bottom side. 2) Remove the battery cover and remove a screw. 3) Remove Escutcheon (The plastic board is stuck on the case with adhesives.)
Page 6
4) The bottom case of the rear panel side is raised, and the bottom case is pulled for a little in the direction of an ar- row. Cautions : When removing the bottom case, take care not damage the cable and connectors. 5) Remove 2 shafts on right and left.
Page 7
Disassemble of the P204 Power Supply PCB P204 Power Supply PCB Remove 7 screws and disconnect 2 connector (J501). Then remove the PCB. Disassemble of the P101 Main PCB P101 Main PCB 1) Insert a thin rod to the hole at the Front panel and push REC LEVEL the REC LEVEL Knob.
Page 8
4) Remove 2 screws and disconnect 4 connectors (J108, J110, J111, J113). 5) Disconnect a connector (J803). Then remove the PCB. Disassemble of the P201 Lcd / Sw PCB P201 Lcd / Sw PCB Remove 8 screws. Then remove the PCB.
Page 9
Disassemble of the Front Panel. 1) Remove INPUT VR PCB on the Front panel and All the 1) INPUT VR PCB PCB on the Top case. 2) The Front panel is locked by 2 hooks (A and B). 3) Hook A and B are raised with fi ngers. The front panel can be removed,...
• CompactFlash (with format) • CompactFlash • Update Disc (90M-PMD660CDR) • (90M-PMD660CDR) Connection 1. Connect Windows PC and PMD660 with USB cable 1. Windows PC PMD660 2. Insert the CompactFlash PMD660 COPY POWER OFF ON Writing procedure When you have already written the update fi le in CompactFlash CompactFlash, please go to No9.
Page 11
Windows PC, and Click the "Stop USB Mass Storage Stop USB Mass Storage Device Device". 6. Slide POWER switch to turn off the unit. 6. PMD660 7. Disconnect USB cable from the unit. 7. PMD660 8. Disconnect AC adapter cable from the unit.
Page 12
13. MPU Firmware updating will be done automatically. fi rmware 14. During the updating, "Update" is displayed on LCD with PMD660 Update blink. 15. Uploading takes about 30 seconds. 16. After Firmware rewriting is completed, the display will show the information display of initial automatically.
5. WIRING DIAGRAM LCD UNIT 22P FFC J705 J704 MIC INPUT UNIT FFC CN POWER UNIT J107 J803 J502 LED SW UNIT (P203) (P204) P201 INTERNAL MIC J501 J702 J703 FFC CN 22P FFC INTERNAL MIC BATTERY CASE JJ02 J111 FFC CN J108 INPUT VR UNIT MAIN UNIT...
10. MICROPROCESSOR AND IC DATA Q120 : µPD703111AGM (MAIN uP) No. PORT Function I/O DET Ext Ini Res 1 JIT1 JIT1 MODE SELECT for SSCG 2 JIT0 JIT0 MODE SELECT for SSCG 3 AVcc AVcc POWER SUPPLY for ADC(+3.3V) +3.3V 4 AVreft AVreft REFERENCE VOLTAGE for...
Page 28
Q120 : µPD703111AGM (MAIN uP) 123 PDH9/D25/_INTPD9/TIUD10 CF_OP CF DOOR CF DOOR 124 PDH10/D26/_INTPD10/ EJECTnINT CF EJECT CPLD INTP110/TCUD11 125 PDH11/D27/_INTPD11/ AC_IN AC IN POWER UNIT INTP111/TCLD11 126 PDH12/D28/_INTPD12/TO11 USB IN CONNECTER 127 PDH13/D29/_INTPD13/TIUD11 nLBO NO USE PAH9(P45) 128 EVdd EVdd POWER SUPPLY(+3.3V) +3.3V...
11. ELECTRICAL PARTS LIST PARTS INFORMATION NOTE ON SAFETY FOR FUSIBLE RESISTOR : RESISTORS The suppliers and their type numbers of fusible resistors 1) 00MGD05 × × × 140, Carbon film fixed resistor, ±5% 1/4W are as follows; 2) 00MGD05 × × × 160, Carbon film fixed resistor, ±5% 1/6W 1.
Need help?
Do you have a question about the PMD660 and is the answer not in the manual?
Questions and answers