Subscribe to Our Youtube Channel
Related Manuals for Mountz HS Series
Summary of Contents for Mountz HS Series
- Page 1 HS-Series Screw Presenter Operation Instructions (Rev 2 9/7/11) Page 1 Corporate Headquarters: 1080 North 11th Street, San Jose, CA 95112 Phone: (408) 292-2214 Fax: (408) 292-2733 www.mountztorque.com...
- Page 2 HS-Series Screw Presenter Operation Instructions Introduction The screw presenter is a high precision yet inexpensive table top screw-feeder designed to enhance productivity. Instead of an operator picking-up screws for the assembly process, screws are placed into the hopper of Surefeed and dispensed for pick-up by assembly tool.
- Page 3 HS-Series Screw Presenter Operation Instructions Adjustment of the Brush Fig 1 Check the height of the brush when it is in a horizontal position. If the brush is not horizontal, adust as follows: Brush Set Screws 1. Turn the timing shaft clockwise the Hex Key Wrench (included). Put a few screws in the rail to check the height of the brush.
- Page 4 HS-Series Screw Presenter Operation Instructions Adjustment of the Bit Guide Unit Bit Guide Unit In a case of using FLAT and Oval Screw Types, replace the screw holding plate. Bit Guide M2.0-M2.3 (Model 2023F) M4.0 (Model 4040F) Holding Plate M2.6-M3.0 (Model 2630F) M5.0 (Model 5050F) Screws 1.
- Page 5 HS-Series Screw Presenter Operation Instructions The Screw Presenter is shipped with a U Funnel on the hold- ing plate, on the Bit Guide, and the center of the rail ditch to Holding Plate keep it in alignment. If, however, the unit was bumped or Holding Plate Set Screw jarred during shipment, these critical parts may have gotten Rail Set Screw...
- Page 6 HS-Series Screw Presenter Operation Instructions Turn on the Screw Presenter Power Switch Insert the AC adapter plug into the DC at the rear of the screw presenter. Insert the AC adapter into the electric outlet Indicator Lamp and turn on the power (the indicator light will come on). Sensors The screw dipping plate and the rail will begin oscillating and the screw presenter will start feeding screws.
- Page 7 HS-Series Screw Presenter Operation Instructions How to Tilt the Screw Presenter The screw presenter should normally be set horizontally. However, if it has difficulty feeding some type of screw smoothly, slant the screw presenter toward the front direction. Lift to use the hex key wrench. Lift the rear of the unit slightly, loosen the slant screws with the hex key wrench and pull out the base bracket (it can be pulled out by about 12mm.
-
Page 8: Troubleshooting
A screw with a spring washer, the diameter of which is Slant the screw presenter. If the unit doesn't feed, contact Mountz narrower than the rail unit, was placed into the bin. The rail has become clogged with dust or oil... - Page 9 HS-Series Screw Presenter Operation Instructions Trouble Shooting Problem: The Screw Sometimes go Through the Screw Passage in an Abnormal Position Cause Solution Inadequate adjustment of the screw passage plate Adjust it properly The screw presenter is tilted more than necessary Tilt the screw presenter only as much as necessary Problem: The Screw Fails to Reach the Specified Position at the Bit Guide Cause...
- Page 10 HS-Series Screw Presenter Operation Instructions Maintenance Always turn off the unit before performing maintenance. Rail Remove all screws in the bin and the rail. Rail Ditch Cleaning the rail: Loosen the rail screw with hex key wrench. Pull the rail unit toward you and take it out. Clean the rail ditch and the top of the rail with a clean cloth.
- Page 11 Mountz Inc. features an experienced calibration and repair staff. Our trained technicians can calibrate and repair most any tool. Mountz provides rapid service with quality that you can trust as we offer three state-of-the-art calibration lab and repair facilities that can calibrate up to 20,000 lbf.ft.
Need help?
Do you have a question about the HS Series and is the answer not in the manual?
Questions and answers