Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Subscribe to Our Youtube Channel
Related Manuals for Draper 04603
Summary of Contents for Draper 04603
- Page 1 Original Instructions Version 2 141CC PETROL CULTIVATOR/ TILLER 04603...
-
Page 2: Preface
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents 1. Preface 9. Basic Operation Instructions 1.1 Product Reference 9.1 Raising the Front Wheel 1.2 Revisions 9.2 Starting the Engine 1.3 Understanding the Safety Content 9.3 Operating the Clutch Lever 1.4 Copyright © Notice 9.4 Stopping the Tiller 2. Contents 9.5 Tips for Using the Tiller 3. -
Page 4: Warranty
This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase. -
Page 5: Product Introduction
Read this manual in full before attempting to assemble, application beyond the conditions established for use operate or maintain the product, and retain it for later use. will be considered misuse. Draper Tools accepts no responsibility for improper use of this product. 4.2 Specification Stock No. -
Page 6: Health And Safety Information
5. Health and Safety Information Important: Read all Health and Safety instructions Operation before attempting to operate, maintain or repair this • Do not operate the engine in a confined space where product. Non-compliance with these instructions may dangerous carbon monoxide fumes can collect. result in injury or damage to the user or the product. -
Page 7: Additional Health And Safety Precautions For This Tilling Machine
E10 fuels before using it in this machine. Draper Tools recommends use of an additive or investigate the cause. stabiliser with E10 fuels to extend the life of the fuel −... -
Page 8: Identification And Unpacking
6. Identification and Unpacking 6.1 Product Overview (20) (17) (12) (18) (15) (21) (10) (23) (14) (22) (13) (19) (16) (11) Air filter (13) Handlebar height adjustment bolts Blade assembly (14) Handlebar support Clutch lever (15) Left handlebar Drag bar (16) Mudguard Drag bar socket (17) Muffler Engine control lever... -
Page 9: What's In The Box
If any part is occurred during shipment. damaged or missing, do not attempt to use the product. Please contact the Draper Helpline; contact details can be found at the back of this manual. 1 x Main assembly including handlebars... -
Page 10: Preparing The Tiller
7. Preparing the Tiller Important: Before attempting to assemble or use this product, read and understand all the safety instructions listed in this manual. (J & L) 7.1 Assembly (15) Fig. 3 b. Pass an M8 x 30mm full-thread flange hex bolt (J) through an M8 washer (L) and the lowest hole in the left handlebar (15) (Fig. - Page 11 7. Preparing the Tiller Fig. 5 Fig. 7 g. Pass the M8 x 35mm half-thread flange bolt (I) 3. Use the handlebar cable clips (E) to secure the cables through an M8 washer (L) and down through the against the handlebars (Fig. 7). handlebar bracket into the support to secure it in place (Fig.
-
Page 12: Checking And Topping Up The Engine Oil
Running the machine with a low oil underestimate the actual level. level may cause serious damage to the engine. Draper Tools recommends SAE 10W-30 oil for general use in all temperatures. CAUTION! DO NOT use non-detergent or two-stroke engine oil as this may reduce the (18) working life of the engine. -
Page 13: Positioning The Front Wheel
7. Preparing the Tiller 7.4 Positioning the Front Wheel 7.5 Adjusting the Handlebar Height (10) Important: ONLY adjust the handlebars while on firm, The front wheel can be located in two positions: level ground. • The lower position can be used to wheel the machine into position. -
Page 14: Adjusting The Tilling Depth
7. Preparing the Tiller 7.6 Adjusting the Tilling Depth 7.7 The Engine Control Lever To adjust the tilling depth, set the height of the drag bar The engine control lever (6) acts as the throttle and (4). The higher the drag bar sits in the drag bar socket (5), controls the supply of fuel to the engine. -
Page 15: Fuelling The Tiller
CAUTION! DO NOT use higher grade petrols as Draper Tools recommends the use of an additive or they contain additives that the engine has not stabiliser when using E10 fuels. Additives and stabilisers been designed to accommodate. -
Page 16: Basic Operation Instructions
9. Basic Operation Instructions Important: Before use, read and understand all the safety instructions listed in this manual. Ensure that all fixtures are securely fastened and that the machine is correctly prepared for use. WARNING! ALWAYS ensure that the control lever is in the STOP position before attempting to start the engine. -
Page 17: Operating The Clutch Lever
9. Basic Operation Instructions 9.3 Operating the Clutch Lever 9.4 Stopping the Tiller The clutch lever (3) engages the power from the engine To stop the machine in an emergency, push the engine to the transmission (Figs. 20 and 21). control lever (6) downwards and towards you into the STOP position (Fig. -
Page 18: Maintenance And Troubleshooting
Important: ALWAYS drain the machine of oil before allow it to cool before maintaining or storing disposal or before returning the machine to Draper Tools. this product. If the engine must be run for Dispose of oil according to local regulations. -
Page 19: Draining The Fuel
Important: Always drain the machine of fuel before 7. Insert the locking barrels and pins to secure the tines disposal or before returning it to Draper Tools. Dispose of in place. fuel according to local regulations. -
Page 20: Air Filter Care
Clean the air filter (1) regularly to ensure consistent air Ensure that the spark plug is clean and correctly gapped. flow to the carburettor. Increase the frequency of Draper Tools recommends spark plugs BPR5ES (NGK) cleaning when working in dusty environments. and F7RTC (LG). -
Page 21: Float Bowl Care
If the machine repeatedly fails to start, check and DO NOT allow the bowl to twist during tightening. clean the float bowl to improve the flow of fuel into If the machine still fails to start, contact Draper Tools for repair and replacement options. 10.8 Transporting the Tiller... -
Page 22: Storing The Tiller
10. Maintenance and Troubleshooting 10.9 Storing the Tiller 4. Drain the engine oil (see 10.2 Replacing the Engine Oil). Prepare the tiller correctly for storage when it is not 5. Raise the drag bar (4) so that the lowest of the in use: grooves is engaged. -
Page 23: Troubleshooting
Push the engine control lever (6) upwards to increase the engine speed. The cable is too long. Replace the faulty part. Contact Draper Tools for The spring has failed. replacement options. The bearing inside the gearbox has failed. There is unusual noise from A bearing inside the gearbox Replace the faulty part. -
Page 24: Spares, Returns And Disposal
Store these materials in suitable containers and dispose of them in accordance with local regulations. Draper Tools and its agents cannot be responsible for the disposal of these substances. At the end of its working life, dispose of the product responsibly and in line with local regulations. -
Page 25: Explanation Of Symbols
12. Explanation of Symbols Hot surfaces Read the instruction manual Warning! Do not touch Oil dipstick and reservoir Do not incinerate or throw onto fire Keep away from fire and open ignition Press primer bulb three times sources; do not smoke nearby Keep bystanders away Do not abandon in the environment Beware of projectiles and debris... - Page 26 Notes – 26 –...
- Page 27 Notes – 27 –...
- Page 28 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 General Fax: +44 (0) 23 8026 0784 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited...
Need help?
Do you have a question about the 04603 and is the answer not in the manual?
Questions and answers