Page 2
NEVER OPERATE THE TENT NEAR AN OPEN FLAMER OR HEAT SOURCE At all times, take precautions that there are no flames, or other heat sources, near the tent fabric or mattress. Neither the tent nor the mattress are fire retardant. NEVER USE ANY PRODUCT THAT BURNS FUEL IN THE TENT Deadly fumes produced by stoves, lanterns, grill,...
TABLE OF CONTENTS DIMENSION AND SPECS..........HARDWARE COMPONENTS..........CROSSBAR OR PLATFORM SETUP........TENT COMPONENTS............TENT INSTALLATION............MOUNTING HARDWARE PREPARATION....... INSTALLING RAIL COMPONENTS........HOW TO OPEN THE GEO SOLO........SETUP INSIDE THE TENT..........HOW TO CLOSE THE GEO SOLO........OPTIONAL ITEMS............TENT CARE AND SAFETY..........
Page 5
Note: Heavy-duty crossbars should be used when adding extra attachments on top. Weight Tent frame & fabric: 52kg (114 Ibs) (excluding all detachables) + Mattress & condensation mat: 56kg (123 Ibs) * Ladder: 7.5kg (16 lbs) Interior Dimension (L x W x H) 86.5" x 31.5" x 51" (220cm x 80cm x 130cm) Exterior Dimension (L x W x H) 88.5"...
HARDWARE COMPONENTS Your GEO SOLO comes with attached latches, a ladder, and a mounting kit with: 6. Mattress (Included air-mesh) 1. Tent 2. Vehicle connection brackets x 6 sets Stainless steel lock plates 7. Ladder bracket x 1 set (1 set equipped on side door) Other Parts included 3.
CROSSBAR OR PLATFORM ADJUSTING THE CROSSBARS Manufacturer recommendation: distance between crossbars should be 36" (91cm) minimum for more stability while driving. This distance is also recommended between mounting points on platform racks. Distance = D PLATFORM RACKS: Any additional accessories on Platform racks can also be used, crossbar should have a vertical...
TENT COMPONENTS Crossbar (option) Main/Sub gas spring Main hinge Stargaze window Air ventilation Front door: Triple-panel Top gasket Closing string Side doors: Dual-panel Locking latch Ladder bracket Rain & Sun shade Middle gasket Corner bracket...
TENT INSTALLATION Parallel with the crossbar. Wind Back side down (drag force). Parallel with the vehicle's body. Check balance from front & back side. Mounting SOLO tent from one side of the vehicle and proper placement.
HARDWARE PREPARATION Prepare 4 bottom locking sets to assemble (2 extra or optional sets). Insert x4 M8 bolts into the C tube Adjust x2 M8 bolts on the 2 sides at the bottom of tent. of the cross bar as the picture shows. 5 - 15 Mark Insert the lock plate to the M8 bolts.
INSTALLING RAIL COMPONENTS We recommend installing your ladder hooks and handle on INSTALL THE HANDLE your vehicle after it is mounted, and the handle should be placed in front of the main door (balanced push-up force). STEP 1 Insert x2 M6 T-Nuts into the groove of the top frame.
Page 12
INSTALLING RAIL COMPONENTS Hook the ladder to the bracket properly and adjust the INSTALL THE LADDER angle so it is stable, and the lock is securely engaged (be sure to adjust height and angle, then lock). STEP 1 First button: Locked for hook fixation (all-time lock/ screwed from side for safety).
HOW TO OPEN THE GEO SOLO STEP 1 Push up gently & slowly, so that the gas spring lifts the top cover into its final position (giving some time for air intake). STEP 2 STEP 3 Caution! A strong and quick lift up will damage the frame and hinge.
Page 14
HOW TO MANAGE GEOMETRIC DOOR MULTIPLE DOOR-OPENING WAYS: 1. Completely open. 2. Full open (don't need to fold the door). 3. Half top opening (ventilation) 4. Half side opening for snowing season. for raining season.
SETUP INSIDE THE TENT The two mesh pockets included: zip up and tuck the door fabric inside, then zip down. The tent has x2 holes on each sides, which a plug can be passed through. When not in use, block with the included PU foam.
Page 16
SETUP INSIDE THE TENT The tent is equipped with a loop in the middle and several O-rings inside, intended for light fixtures or lanterns. Put up the ventilation support Should fold before closing! bars - otherwise it will dent on TPU window.
HOW TO CLOSE THE GEO SOLO Leave the bottom zipper puller (red) close 50%, which prevent water inside when heavy rain. LIME 100% closed Close before folding 1 per side door 2 for front door 2 ventilation support bar...
Page 18
HOW TO CLOSE THE GEO SOLO 1. Holder 2. Support bar 3. Top ventilation support bar - Fold before closing, otherwise it will dent TPU window STEP 1 Remove the door frame support bar, and drop it back after you close both side windows. Push back STEP 2 STEP 2...
Page 19
The inner connector (2 elastic band system) helps the skin to fold neatly when you close the tent. Caution! Be aware that holding strap is highly elastic and once removed it can discharge. Keep children away. You can wrap it and store it in the pocket when not in use.
Page 20
When it's nearly closed, tuck in the fabric from three sides, then put the string inside the tent. Check the gap Check the gap Check the gap Check the gap Check the gap Check the gap After tent is closed, be sure to lock latches on both sides of the tent and check side gaps (water penetration path) on both sides.
TENT CARE AND SAFETY TENT CARE While it is not possible to make a tent that is 100% waterproof, the GEO SOLO RTT is designed to achieve maximum water resistance. We suggest the following precautionary measures to aid in this.
Need help?
Do you have a question about the GEO SOLO RTT and is the answer not in the manual?
Questions and answers