Related Manuals for Solid Optics EDFAMUX V2
Summary of Contents for Solid Optics EDFAMUX V2
- Page 1 EDFAMUX V2 User & Installation Manual EDFAMUX | SO-DUAL-EDFA | SO-EDFA Version 2.6 (April 2024)
- Page 2 Solid Optics EDFAMUX. For any Should you have any comments on this manual, please direct them to: Solid Optics EU N.V. | Veluwezoom 15E 1327 AE Almere | Phone: +31(0)88 342 3776 | Mail: info@solid-optics.com...
- Page 3 We guarantee that the product you receive has been thoroughly tested to ensure that it meets its published specifications. The warranty included in the conditions of delivery is valid only if the product has been installed and used according to the instructions supplied by Solid Optics. We shall in no event be liable for incidental or consequential damages, including without limitation: lost profits, loss of income, loss of business opportunities, loss of use and other related exposures, however caused, arising from the faulty and incorrect use of the product.
-
Page 4: Table Of Contents
CONTENT Warnings & Symbols Technical Description Physical Installation Configuration 4.1. Initial Configuration 4.2. Network Configuration 4.2.1. ETHERNET Configuration 4.2.2. SNMP Configuration 4.3. Firmware Upgrade 4.4. Password Configuration 4.5. Command Line Reference 4.6. HTTP API Specification Safety Guidelines & Warnings Drawings, Circuit Diagrams & SIMPLEX Channels In Case of Malfunction Maintenance Technical Support... -
Page 5: Warnings & Symbols
ANATEL This symbol indicates that the equipment complies with Directives 2011/65/EU This symbol indicates that Solid Optics EU N.V. has tested the equipment in accor- (RoHS II) and 2002/95 EC (RoHS I). dance with the relevant Brazilian standard, ensuring its safety. The Anatel symbol confirms compliance with Anatel regulations, indicating that the product does not generate electromagnetic disturbance or is affected by it. -
Page 6: Technical Description
3. PHYSICAL INSTALLATION Warnings: The intra-building port(s) (list the port or ports) of the equipment or subassem- Requirements: bly is suitable for connection to intra-building or unexposed wiring or cabling Before proceeding, make sure you have the following items: only. The intra-building port(s) of the equipment or subassembly MUST NOT be metallically connected to interfaces that connect to the OSP or its wiring for more •... -
Page 7: Configuration
4.1. Initial Configuration Alternatively, access the EDFAMUX management website by typing the previously To ensure a smooth installation process for the Solid Optics EDFAMUX, please fol- assigned IP address into a web browser.EDFAMUX that you created in the previous low these steps:... -
Page 8: Network Configuration
”Figure 1” Click on “Save”. If adjustments are needed, follow these steps (based on p.8): Click on the slide button to enable: 2. Perform a Ping (For troubleshooting or verification): “Manually override amplification values”, Enter the destination IP address. Modify values accordignly: Click on “Ping”. -
Page 9: Firmware Upgrade
4.3. Firmware Upgrade For firmware updates, navigate to the EDFA management site and select the Firmware menu. Click on the download button to access the download page, where you can find the latest firmware version. Once on the download page, scroll down and locate the version labeled NMUv2 "Figure 3"... -
Page 10: Command Line Reference
4.5. Command Line Reference only, all other commands are get/set. All set commands require the user to be in The serial console connector adheres to Cisco specifications, Baud rate 115200, configure mode. Exit can be used to leave configure mode without committing 8 bits, 1 stop bit, no parity or flow control. -
Page 11: Http Api Specification
(Wi-Fi status, SSID, password) EDFA data General: (readings, min/max values, tunable/static, DCM status) Use the Solid Optics EDFAMUX only for the purpose it was designed for. • Reboot device (see above) 10- SNMP data • To avoid overheating the EDFAMUX, please use the appropriate and qualified... - Page 12 Please follow all local and national laws and regulations when optical connectors to connect optical cables. Unlike electrical wires, the insides disposing of the Solid Optics EDFAMUX after deinstallation. of optical cables contain a fiber made of glass. Due to the different properties of...
-
Page 13: Drawings, Circuit Diagrams & Simplex Channels
DRAWINGS, CIRCUIT DIAGRAMS & SIMPLEX CHANNELS 482,6 mm/19’’ 482,6 mm/19’’... - Page 14 EDFAMUX Interface Block Diagram QSFP included for connection clarification...
- Page 15 SIMPLEX Channels 10 x 10G 80km CH28-37 10 x 10G 80km CH42-51 8 x 100G 80km CH29-36 8 x 100G 80km CH42-49 CH28 CH42 CH29 CH42 CH29 CH43 CH30 CH43 CH30 CH44 CH31 CH44 CH31 CH45 CH32 CH45 CH32 CH46 CH33 CH46 CH33...
-
Page 16: In Case Of Malfunction
Contact, please refer to chapter "9. Technical Support " of this manual. Warranty We offer a 3-year warranty for normal usage of the Solid Optics EDFAMUX, pro- vided that the user has not altered the EDFAMUX in any way or used it contrary to its intended purpose. -
Page 17: Maintenance
MAINTENANCE Power Supply Replacement Instructions: No regular maintenance is required for the EDFAMUX when placed in a normal 1. Please have the replacement power supply on hand. clean environment compliant to the requirements set forth in the specific data- 2. Unscrew the power supply and take it out. sheet applicable to the chosen EDFAMUX model. -
Page 18: Technical Support
Informa- USA: tion is subject to change without notice. Solid Optics and the Solid Optics logo Solid Optics US are registered trademarks of Solid Optics EU Holding N.V. All other trademarks... - Page 19 Get in touch EU Customer Support US Customer Support +31 (0) 88 342 3776 +1 855 678 4271 info@solid-optics.com infous@solid-optics.com...
Need help?
Do you have a question about the EDFAMUX V2 and is the answer not in the manual?
Questions and answers