1. Manuals
  2. Brands
  3. Solid Optics Manuals
  4. Switch
  5. EDFAMUX V2
  6. User & installation manual

Solid Optics EDFAMUX V2 User & Installation Manual

Hide thumbs Also See for EDFAMUX V2:
Table of Contents

Advertisement

Quick Links

Download this manual
SO-DWDM-10x10G-EDFAMUX-140km • SO-DWDM-16x10G-EDFAMUX-140km •
SO-DWDM-8x100G-EDFAMUX-80km • SO-DWDM-8x100G-EDFAMUX-120km •
SO-DWDM-16x100G-EDFAMUX-40km • SO-DWDM-16X100G-EDFAMUX-80km
Technical Support Contacts
Europe:
Solid Optics EU
Phone: +31 883 423 776
edfamux@solid-optics.eu
USA:
Solid Optics US
Phone: +1 855 678 4271
edfamux@solid-optics.com
U
S
E
R
&
I
N
S
T
A
U
S
E
R
&
I
N
S
T
A
E
D
F
A
E
D
F
A
SO-DWDM-10x10G-EDFAMUX-200km
Version 2.2 (October 2020)
L
L
A
T
I
O
N
M
A
N
L
L
A
T
I
O
N
M
A
N
M
U
X
V
2
M
U
X
V
2
U
A
L
U
A
L
Solid Optics EU N.V.
Veluwezoom 15E
1327 AE Almere
The Netherlands
Phone: +31 (0) 88 3423776
Website:
www.solid-optics.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EDFAMUX V2 and is the answer not in the manual?

Questions and answers

Related Manuals for Solid Optics EDFAMUX V2

Summary of Contents for Solid Optics EDFAMUX V2

  • Page 1 & SO-DWDM-10x10G-EDFAMUX-140km • SO-DWDM-16x10G-EDFAMUX-140km • SO-DWDM-10x10G-EDFAMUX-200km SO-DWDM-8x100G-EDFAMUX-80km • SO-DWDM-8x100G-EDFAMUX-120km • SO-DWDM-16x100G-EDFAMUX-40km • SO-DWDM-16X100G-EDFAMUX-80km Version 2.2 (October 2020) Technical Support Contacts Solid Optics EU N.V. Veluwezoom 15E Europe: 1327 AE Almere The Netherlands Solid Optics EU Phone: +31 (0) 88 3423776 Phone: +31 883 423 776 edfamux@solid-optics.eu...
  • Page 3 Solid Optics EDFAMUX product line. Solid Optics EDFAMUX products undergo extensive internal testing procedures in order to meet our strict quality control standards and are in full compliance with CE (including RoHS and REACH), WEEE and FCC- regulations.
  • Page 4 The warranty included in the conditions of delivery is valid only if the product has been installed and used according to the instructions supplied by Solid Optics. We shall in no event be liable for incidental or consequential damages, including without limitation: lost profits, loss of income, loss of business opportunities, loss of use and other related exposures, however caused, arising from the faulty and incorrect use of the product.

  • Page 5: Table Of Contents

    CONTENT Warnings and Symbols Page 5 Technical Description Page 6 Configuration Page 6 Initial Configuration Page 6 Network Configuration Page 8 3.2.1 Ethernet Configuration Page 8 3.2.2 SNMP Configuration Page 9 Firmware Upgrade Page 10 Password Configuration Page 10 Command Line Reference Page 11 HTTP API Specification Page 12...

  • Page 6: Warnings And Symbols

    #31 = Paper or Fibreboard / Plastic CE MARK This symbol indicates that Solid Optics EU N.V. tested the equipment in accordance with applicable European standards and it is safe. The CE-symbol indicates that this product also complies with the requirements of Directive 2014/30/EU. It does not generate, or is not affected by, electromagnetic disturbance.

  • Page 7: Technical Description

    This equipment can operate with 110v AC, 220v AC and 48v DC, depending on which power supplies are installed. 3. CONFIGURATION 3.1. INITIAL CONFIGURATION For visual step-by-step instructions on how to install the Solid Optics EDFAMUX, please visit the Knowledge Base/Tutorials Section on our website at www.solid-optics.com. The Knowledge Base...
  • Page 8 e. set ethernet gw commit 4) Access the EDFAMUX with a web browser (this is the management website) at the following address and use “admin” as password or continue with the CLI (see command line reference): http://{EDFAMUX_IP}/settings.html, click in “Optical”, enter your Fiber Length (1) and click “Apply changes”...

  • Page 9: Network Configuration

    12) Before connecting each DWDM optic to the corresponding channel on the EDFAMUX, use an optical power meter or a DWDM OSA meter to verify that the TX values of the EDFAMUX channel are lower than: a. In the case of the 100G EDFAMUX: 8dBm (aggregate damage threshold of the optic). b.

  • Page 10: Snmp Configuration

    3.2.2. SNMP CONFIGURATION The EDFAMUX uses SNMP version 2c - Please use the provided MIB file or enter download.solid-optics.com to obtain it. In the Ethernet configuration submenu you can configure the Syscontact (1), Syslocation (2), SNMP port (3) and the community string (4).

  • Page 12: Firmware Upgrade

    3.3. FIRMWARE UPGRADE The Firmware page is used to upgrade the firmware and the website of the EDFAMUX - Proceed as follows: 1) Upload the provided firmware.bin file (1) and click on “Update” (2). 3.4. PASSWORD CONFIGURATION The Password configuration page is used to change the password used to access the SETTINGS and FIRMWARE pages (password timeout is 15 minutes) –...

  • Page 13: Command Line Reference

    3.5. COMMAND LINE REFERENCE The connector for the serial console conforms to Cisco specification, Baud rate 115200, 8 bits, 1 stop bit, no parity or flow control. The following commands are available. Commands in require authentication, Commands in green are get only, all other commands are get/set. All set commands require the user to be in configure mode.

  • Page 14: Http Api Specification

    10- SNMP data 22- Sensor data (same data as in API 5/readings, but keyed as floating-point values for easy readouts) END-OF-LIFE DISPOSAL Please follow all local and national laws and regulations when disposing of the Solid Optics EDFAMUX after deinstallation.

  • Page 15: Recommended Edfa Values

    4. RECOMMENDED EDFA VALUES The following recommended values are to be considered while using the maximum Fiber length of your network. Booster values may need to be adjusted if a shorter Fiber length is used. The following values are based on a 10G SFP+ sending +1dBm of light power for the 10G 140km and 10G 200km EDFAMUX models, and a 100G QSFP sending -6.5dB of light power for the 100G EDFAMUX models.

  • Page 16: Safety Guidelines And Warnings

    EDFAMUX. GENERAL • Use the Solid Optics EDFAMUX only for the purpose it was designed for. To avoid overheating the EDFAMUX, please use the appropriate and qualified rack space and • only use the EDFAMUX in spaces designed to store/use regular network equipment (no harsh or extreme environments).
  • Page 17 REGARDING FIBER OPTIC CABLES: The EDFAMUX is designed to include fiber optic components/products, including optical connectors to connect optical cables. Unlike electrical wires, the insides of optical cables contain a fiber made of glass. Due to the different properties of optical fiber when compared to the copper used in electrical wires, some additional precautions must be taken as detailed below: Avoid bending fiber-optic cable beyond its minimum bend radius.

  • Page 18: Drawings, Circuit Diagrams And Photos

    6. DRAWINGS, CIRCUIT DIAGRAMS & PHOTOS Outline Dimensions EDFAMUX Interface Block Diagram PRE_AMP QSFP POST- DEMUX QSFP included for connection clarification...

  • Page 19: Maintenance

    WARRANTY We offer a 3-year warranty for normal usage of the Solid Optics EDFAMUX, provided that the user has not altered the EDFAMUX in any way or used it contrary to its intended purpose. For specific information regarding our warranty, please visit www.solid-optics.com...

  • Page 20: Contact Information

    Solid Optics EU Holding N.V. All other trademarks are acknowledged as registered trademarks and proprietary to their respective owners. Copyright © 2019 Solid Optics EU N.V., Dutch Chamber of Commerce no. 39099087, all rights reserved. For more information visit www.solid-optics.com...

Table of Contents