Page 2
WWW.GOPOWERBIKE.COM DO NOT RETURN TO STORE! If you need any help with your new GoAir bike, whether it is missing parts or you need help with assembly, please email us at Help@gopowerbike.com. We will be sure to respond!
Page 3
Welcome Thank you for purchasing the GoAir from GoPowerBike. We take pride in bringing you a quality product that will offer years of enjoyment. Please read and understand this manual fully before assembling and riding your bike. If you have any questions after reading this manual, please reference the GoPowerBike Help Center or contact us by email.
Table of Contents Using This Manual General Info Safety Check and Other Information Getting Started How to Fold Your Ebike Installing the Pedals Adjusting the Handlebars Adjusting the Seat Charging Your Ebike Installing the Battery Get To Know Your Ebike Battery and Charging Riding Your Ebike Maintenance...
Assembly and first adjustment of your bike from GoPowerbike requires special tools and skills and it is recommended that this should be done by a certified, reputable bike mechanic if possible.
NOTICE: A critical aspect of assembling your bike by GoPowerbike is securing the front wheel and checking the tightness of the rear wheel axle nuts. All bikes by GoPowerbike use a quick release front wheel mounting mechanism and the rear wheel is bolted on. These mechanisms may become loose or unsecured during shipment or over time.
If the throttle, brake lever cutoff switches, pedal assistance, or lighting are functioning abnormally, intermittently, or not working, please discontinue using your ebike immediately and contact the GoPowerbike Product Support team for assistance. Quick Release Levers Quick release levers are located on your ebike to secure the seat post. These provide convenience to the user since they allow the seat post to be adjusted without tools.
Page 8
Loose, worn, or damaged handlebar grips should be replaced before you ride and can be purchased from GoPowerbike. The seat and seat post should be properly aligned, fitted to the user, and the seat post quick release should be properly tightened, fully closed, and secured before riding.
Getting Started Starting notes: · Remove all packaging before beginning assembly. · The directions given in this manual—right, left, front/forward, and rear/back—are oriented as the rider would see them when seated on the bike. The “right side” of the bike, for example, is the side where the rider’s right hand and foot will be. ·...
Unfolding the Stem Step 1: Pull the handlebars to the upright position Step 2: Push the latch in firmly until it locks in position Step 3: Pull on the latch to confirm it is locked and the handlebars cannot fold. Folding the stem Step 1: Open the lever Step 2: Pull the latch away from the stem...
Page 12
Folding the Frame Step 1: Lift the locking lever at the folding hinge to unlock Step 2: Open the folding lever on the frame Step 3: Fold the bike in half so that the front wheel is next to the rear wheel. Locking Lever Folding Lever...
Installing the Pedals Step 1: Align the spindle on “R" pedal with the hole at the end of the crank arm on the right side of the bike. Step 2: Hold the pedal base steady and, taking care that the spindle enters the hole straight on, use your other Crank Arm hand to twist the spindle clockwise into...
Page 14
Step 3: Finish inserting and then tightening the spindle into the crank arm by turning it clockwise Step 4: Check that the right pedal is secure. Step 5: Repeat steps 2 – 5 with the left (“L") pedal. NOTICE - the spindle on the left pedal is reverse threaded and needs to be inserted and tightened with counterclockwise turns.
Adjust the Handlebar Height Step 1: Unlatch the stem clamp Step 2: Move the handlebars to the desired height Step 3: Retighten the stem clamp NOTICE! Always insert the Minimum telescoping stem past the insertion line minimum insertion point marked on the stem.
Adjusting the Seat Post Step 1: Loosen the seat post clamp Step 2: Raise or lower the seat post in the seat tube Step 3: Check that the seat is straight Step 4: Retighten the seat post clamp Minimum insertion line NOTICE! Always insert the seat post past the minimum insertion...
Charging Your Ebike Connect the DC jack of the charger to the charging port of your ebike and then the AC plug into the outlet. The charger light turns from red to green when charging is complete. ------ Still Charging ------ Fully Charged Charging Indicator Light NOTICE - Important charging notes:...
Installing the battery Step 1: Push down the lever and remove the dust cover from the battery mount Step 2: Move the sliding cover on the back of the battery to connect the battery to the battery mount on the handlebars. The battery is connected by a magnet.
Lights On/Off: Press the battery power button again to turn on the light. Press the power button to turn off the light. Shifting: There are 6 speeds on the GoAir ebike. To change speeds, twist the rapid shifter on the right handlebar while pedaling.
Riding your ebike 1. Do not use the eBike before reading this manual carefully and knowing your eBike thoroughly. 2. Do not lend your eBike to anyone who do not know how to use it, so as to avoid harm. 3.
Need help?
Do you have a question about the GoAir and is the answer not in the manual?
Questions and answers