Subscribe to Our Youtube Channel
Related Manuals for madVR Labs madVR Envy
Summary of Contents for madVR Labs madVR Envy
- Page 1 Envy JVC Laser Projector Setup Guide www.madvrenvy.com Rev. 2.05 madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
-
Page 2: Projector Settings
1.0 Introduction Welcome to the madVR Envy Setup Guide for the JVC laser projectors. This guide shows how to configure your projector for SDR (Standard Dynamic Range) and HDR (High Dynamic Range) content, to get the best results from your Envy. This guide covers topics specific to using the JVC with the Envy. For general JVC setup information, please refer to the JVC Owner’s Manual. - Page 3 “Natural”, Color Profile to Auto, Color Temperature to 6500K, and a Gamma to 2.4. Other settings in this Picture Mode can be set to your preference (Laser Level, Dynamic Control, Aperture, etc.), like shown below: madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 4 3. Note or set the password in the JVC Network settings. 4. From the Envy Device IP Control Configuration Menu, choose Find Devices. 5. Under the Display section, select the JVC. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 5 This method also uses the Envy’s HDR Flag, which will trigger the JVC to switch to the proper Picture Mode for the content being viewed. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 6 BT.2020 (Normal) because they prefer a brighter image and the difference in gamut coverage can be indiscernible in most scenes. The Color Temp. should be set to 6500K. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 7 Next, select the Tone Mapping menu line in the User 4 Picture Mode. This brings up a sub-menu with several options. Select Custom 1. Then go to the Correction Value menu line, and in the sub-menu, select Import. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 8 Go to the Content Type Line, and select Auto, as shown below. With this setting in place, the JVC will then automatically switch to the Picture Modes you selected in the AutoPic.ModeSelect Menu for both SDR and HDR content. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 9 Envy will use a 2.2 gamma, but rather this is required so that the Envy and the JVC are “on the same page” and so the dynamic HDR tone mapping will be correct and irrespective of the set gamma value. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 10 After changing the settings as outlined below, be sure to press the Green button on the Envy Remote on any setting marked as TEMP in the menu to permanently save your changes. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 11 Screen Gain and then dividing by Pi (3.14). After measuring your peak luminance, enter it in the Envy Display Configuration menu, like shown in the image below. madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 12 Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
- Page 13 (e.g., “BT.2020” or “BT.709”), and check the JVC Picture Mode menu to confirm the projector is using the corresponding correct color space (revisit steps 2 and 3 in the Projector Settings section). madVR Envy – JVC Setup Guide Copyright © madVR Labs, LLC. All rights reserved.
Need help?
Do you have a question about the madVR Envy and is the answer not in the manual?
Questions and answers