Haier HSU-18H03 Installation Manual
User manual
Hide thumbs
Also See for HSU-18H03:
- Operation manual (18 pages) ,
- Installation manual (13 pages) ,
- Operation manual (30 pages)
Table of Contents
Advertisement
Quick Links
Installation Manual of Room Air Conditioner
1.Driver
2.Hacksaw
3.Hole core drill
4.Spanner(17,19 and 26mm)
Accessory parts
No.
Accessory parts
1
Remote controller
2
R-03 dry battery
3
Mounting plate
4
Drain hose
4X50
5
Steel nail, cement
6
4X25
Plastic cap
Screw
7
Drain-elbow
Cover
8
9
Cushion
No.0010515846
Necessary Tools for Installation
5.Torque wrench(17mm,22mm,26mm)
6.Pipe cutter
7.Flaring tool
8.Knife
Drawing for the installation of indoor and outdoor units
Number
of
articles
1
2
1
Optional parts for piping
Mark
Parts name
1
A
Non-adhesive tape
Adhesive tape
B
6
C
Saddle(L.S) with screws
Connecting electric cable
D
4
for indoor and outdoor
Drain hose
E
F
Heating insulating material
1
Piping hole cover
G
1
4
Arrangement of piping directions
Left
Read this manual before installation
Explain sufficiently the operating means to the user
according to this manual.
Rear left
Rear
right
Right
Below
The marks from
The distance between the indoor unit and the floor should be
more than 2m.
9.Nipper
10.Gas leakage detector or
soap-and-water solution
11.Measuring tape
Attention must be paid to
the rising up of drain hose
to
in the figure are the parts numbers.
A
G
12.Reamer
G
F
A
C
D
E
Advertisement
Table of Contents
Related Manuals for Haier HSU-18H03
Summary of Contents for Haier HSU-18H03
-
Page 1: Installation Manual Of Room Air Conditioner
Piping hole cover Cover Cushion Arrangement of piping directions Rear left Rear Left right Right Below The marks from in the figure are the parts numbers. The distance between the indoor unit and the floor should be more than 2m. No.0010515846... -
Page 2: Selection Of Installation Place
Before inserting power plug into receptacle, check the voltage without fail. The power source is the same as the corresponding name plate. Install an exclusive branch circuit of the power. A receptacle shall be set up in a distance where the power cable can be reached. Do not extend the cable by cutting it. Selection of pipe To this unit, both liquid and gas pipes shall be insulated as they become Iow temperature in operation. -
Page 3: Installation Of The Indoor Unit
2. Make sure once more the proper level of the plate, by hanging a thread with a weight from the central top of the plate, then fasten securely the plate with the attachment steel nail. - Page 4 Indoor unit 1. Insert the drain hose into the dent of heat insulation materials of indoor unit. 2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them. 3. Coat the flaring seal face with refrigerant oil and connect pipes.
-
Page 5: Easily-Demount Cleaning Of Indoor Unit
1. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of power cable is H05/07 RH-F or 245IEC57(YZW).The type of connecting wire is H05/07RN-F or 245IEC57(YZW). -
Page 6: Installation Of Outdoor Unit
Install according to 2.Connection of pipes To bend a pipe, give the roundness as large as possible not to crush the pipe,and the bending radius should be 30 to 40 mm or longer. Connecting the pipe of gas side first makes working easier. - Page 7 Brand new outdoor unit is charged 80g more refrigerant than regulated weight. Only for first installation, this extra 80g can be used to purge air in pipes. During this procedure, 80g refrigerant will be discharged in piping.
-
Page 8: Power Source Installation
Please pour water in the drain pan of the indoor unit, and confirm that drainage is carried out surely to outdoor. In case that the attached drain hose is in a room, please apply heat insulation to it without fail.