Advertisement

Quick Links

Stellar TK-21xx Series
Kiosk
User Manual
SOME IMPORTANT NOTES
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement résidentiel,
cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application. Please note that all of TK series kiosk are NOT designed to work direct sunshine
both indoors and outdoors.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne autre
que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le problème qui
se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de
cette marchandise. Le fabricant n'est en aucun cas responsable de tout dommage ou danger
causé par une mauvaise application. Veuillez noter que tous les kiosques de la série TK ne
sont PAS conçus pour fonctionner sous un ensoleillement direct à l'intérieur et à l'extérieur.
TK-21xx Ver. C0
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stellar TK-21 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for POSIFLEX Stellar TK-21 Series

  • Page 1 Stellar TK-21xx Series Kiosk User Manual SOME IMPORTANT NOTES FCC NOTES This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
  • Page 2 警告使用者 為避免電磁干擾,本產品不應安裝或使用於住宅環境。 SAFETY INSTRUCTIONS This equipment is not suitable for use in locations where children are likely to be present. Never open the equipment. For safety reasons, the equipment should be opened only by qualified skilled person. The power outlet socket must be located near the equipment and must be easily accessible.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS PRODUCT OVERVIEW ........... 5 1.1 Product Features .................. 5 1.2 Specification and Drawing ..............5 Specification ..................5 Outline Dimension Drawing ............. 7 1.3 Product Views ..................10 1.4 Introduction to PC Box ..............11 I/O Ports of the TK-2111 ..............11 I/O Ports of the TK-2131 ..............
  • Page 4 Thermal Printer PP-7900K .............. 22 Status LED Indicator SI-100 ............27 Camera Module CM-100 ..............28 Proximity Sensor SU-100 ............... 28 PT-200 Pedestal ................28 4.2 Optional Items..................29 PT-200 Pedestal with Optional Card Dispenser CAD-100S and Bill Acceptor BA-600ME/BA-900ME ..........29 2D Barcode Scanner................
  • Page 5: Product Overview

    1. Product Overview 1.1 Product Features  Fan-less Design  An Interactive, Multi-Function and High-Performance Kiosk  Various Configuration Options: Floor-Standing or Counter-top Style  Support Full HD 21.5” True-Flat PCAP Touch Screen  Modular Design for Easy Serviceability  Various Peripheral Options for Each Unique Need: Can Be Integrated with 2D Barcode Scanner, Thermal Printer, WiFi, Proximity Sensor, Camera, Fingerprint Sensor, MSR, NFC/RFID Reader, Bill Acceptor,...
  • Page 6 3” thermal printer, 250mm/sec.(max.) (PP-7900K) Printer Proximity sensor (SU-100) Proximity Sensor 1. Range from 45cm ~ 80cm (for dark color objectives) 2. Range from 45cm ~ 150cm (for light color objectives) Camera 1MP wide angle camera (CM-100) Status Indicator 3-color status LED indicator (SI-100) Main Display &...
  • Page 7: Outline Dimension Drawing

    Fanfolded ticket printer for ticket thickness: .004” to .011”, Ticket Printer ticket width: 2.0” to 3.25” Bill Acceptor Storing up to 900 notes Integrated RFID reader/writer, supporting ISO 14443 Type A/B contactless Card Dispenser cards; Storing up to 262 cards Environmental Operating 5°C - 40°C, 20%RH - 90%RH...
  • Page 8 Appearance (Pedestal) Appearance (Base) 625.03...
  • Page 9 Appearance (Top) Counter-top Version Appearance (Counter-top Base Plate)
  • Page 10: Product Views

    1.3 Product Views 3-color Status Indicator Camera Module Window Reserved for 2-in-1 Proximity Sensor Lens Device of Printer Receipt Exit MSR/Fingerprint Sensor (Option) Reserved for NFC/RFID Reader (Option) 2D Barcode Custom Bracket for EMV Scanner Window Payment Device (Option) (Option)
  • Page 11: Introduction To Pc Box

    Connector Power Button COM2 LAN Ports COM1 9V DC-OUT (RJ50) (RJ50) Power Jack 12V DC-IN Power Jack Micro USB OTG Micro SD Card Slot Note1: Mini DP is carried through EDP signal, and it is for Posiflex hub board only.
  • Page 12: I/O Ports Of The Tk-2131

    Speaker Connector Power Jack USB 2.0 Ports USB 2.0 Ports COM1 (DB9) Power Button LAN Ports COM3 COM2 (RJ50) (RJ50) 12V DC-IN Power Jack Note1: Mini DP is carried through EDP signal, and it is for Posiflex hub board only.
  • Page 13: I/O Ports Of The Tk-2151/2132

    Speaker Connector Power Jack USB 2.0 Ports USB 2.0 Ports COM1 (DB9) Power Button LAN Ports COM3 COM2 (RJ50) (RJ50) 12V DC-IN Power Jack Note1: Mini DP is carried through EDP signal, and it is for Posiflex hub board only.
  • Page 14: I/O Ports Of The Tk-2152

     I/O Ports of the TK-2152 Hub Board Power Connector HDMI Port USB 3.0 Ports 9V DC-OUT Mini DP Speaker Connector Power Jack USB 2.0 Ports USB 3.0 Ports COM1 (DB9) Power Button LAN Ports COM3 COM2 (RJ50) (RJ50) 12V DC-IN Power Jack Note1: Mini DP is carried through EDP signal, and it is for specific hub board only.
  • Page 15: Product Installation

    2. Product Installation 2.1 Standard Pedestal (PT-200) Floor-Standing Installation Package Contents for Floor-Standing with PT-200 Pedestal Installation Confirm that you have 3 main parts:  Main System Unit: TK-21x1 Series Main System with Touch Monitor……...…………...x1  PT-200 Pedestal.………………………………………...…………..…x1  Base Plate………………………………………………...…………..x1 List of Accessories ...
  • Page 16 Next, open the front door of the pedestal. Lift the key on the left side of the pedestal, and then open the front door. Please follow the below picture. 3. Insert 4 M5-8L screws from the pedestal 4 screw holes from bottom to top, and then use a screwdriver to screw the screws into the 4 screw holes of the main system unit.
  • Page 17: Counter-Top Version Installation

    4. Pull down the power cord from the main system unit. Drive the power cord out of the cable exit at the lower portion of the inside of the pedestal, and then pull it out of the cable exit at the lower portion of the outside of the pedestal.
  • Page 18 Step-by-Step Installation First, take the counter-top base plate out of the packing box. Then fix the counter-top base plate to the TK-21x1 Series system with four M5-10L screws. Please refer to the picture. Second, there are two screw holes on the base plate on the rear side of the ϕ...
  • Page 19 Third, turn the key of the main system unit to the right. And then pull the front door of the main system unit to slide open like a drawer. After opening the front door of the main system unit, you can see a screw ϕ...
  • Page 20: Powering On/Off The Kiosk

    3 Powering ON/OFF the Kiosk 3.1 Open the Touch Monitor Kit Turn the key of the belly system unit to the right. Then pull the front door of the belly system unit to slide open like a drawer. (1) Push upwards the pusher on the left side of the printer in the belly system unit and then (2) open the monitor.
  • Page 21: Close The Touch Monitor Kit

    Push the front door of the belly system unit to slide close like a drawer. 3.5 Driver Download If your kiosk system is shipped without OS pre-installed, please download the relevant driver that you need from the Posiflex website (https://download.posiflex.com/en-global/Download/index/driver/Kiosk/Stellar_TK- 2100-Series).
  • Page 22: Peripherals And Accessories

    4 Peripherals and Accessories 4.1 Standard Items  Thermal Printer PP-7900K Front View Power LED Indicator Error LED Indicator Paper-out LED Indicator Feed Button Paper Exit Cover Open Lever Paper Cover Wedge Groove Paper Near End Sensor...
  • Page 23 Part Names Description Power LED Indicator This indicator turns on when the printer is on. Error LED Indicator This indicator works when the printer has something wrong. For more details, refer to the Status LED Indicators section given below. Paper-out LED This indicator turns on when the paper-out issue Indicator occurs.
  • Page 24 Next, set the paper width by using PP-7900 Series thermal Printer Software Switch Utility for Windows. The software switch utility can be downloaded from the Posiflex’ global website: https://download.posiflex.com/en- global/Download/index/driver/Kiosk/Stellar_TK-2100-Series. To get more detailed information on the paper width jumper setting, contact directly the Posiflex’...
  • Page 25 Error LED indicator is flashing Power off the printer; after 10 seconds, power it back on. If the error LED indicator turns on again even after turning the power back on, malfunction may occurs. Contact your dealer or Posiflex’ technical service team. Specifications General...
  • Page 26 NV Graphics 256KB (max.) Receive Buffer Windows Driver (APD), OPOS, JavaPOS (Win), Printer Driver CUPS Driver (Linux) Posiflex Utility (Android), PP-7900 Utility Software (Windows Desktop), Development Tool (Android SDK), Monitoring Tool (RMS) Blue LED – On = Power LED Indicators...
  • Page 27: Status Led Indicator Si-100

    The default LED status is described below. Status Description A flash of green Kiosk powered on ※ The product information and specifications are subject to change without prior notice. To get more detailed information of SI-100, please contact the service team of Posiflex.
  • Page 28: Camera Module Cm-100

     Camera Module CM-100 Camera Module CM-100 Basic Specification Camera 1MP wide angle camera Output Interface USB 2.0 interface Input Supply Voltage Vertical 50.8° Field of View Horizontal 86.6° Diagonal 100° ※ The product information and specifications are subject to change without prior notice.
  • Page 29: Optional Items

    PT-200 Pedestal with Optional Card Dispenser CAD-100S and Bill Acceptor BA-600ME/BA-900ME Card Exit Bill Acceptor (Option) Card Dispenser (Option) Cash Slot To get more detailed information of PT-200 pedestal, please contact the service team of Posiflex.  2D Barcode Scanner Overview Beeper Interface Cable Connector...
  • Page 30 Scanner Maintenance The scanner is designed for long-term trouble-free operation and rarely requires any maintenance. Only an occasional cleaning of the scanner window is necessary in order to remove dirt and fingerprints. Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to avoid the scan window from being scratched and damaged.
  • Page 31: Wifi Module Wf-660K

    ※ The product information and specifications are subject to change without prior notice. To get more detailed information of WF-660K, please contact the service team of Posiflex.  WiFi Module WF-770K (for TK-2111; Android Version) WiFi Module WF-770K Basic Specification...
  • Page 32: 2-In-1 Device Of Msr/Fingerprint Sensor Mf-2100

    Before installing the drivers of the MF-2100 MSR/fingerprint sensor, after installing the MF-2100 attachment, power on the TK Series kiosk. Installing and Starting the USB MSR Manager Before installing the USB MSR Manager, please visit Posiflex official website (https://download.posiflex.com/en- global/Download/index/driver/Kiosk/Stellar_TK-2100-Series) to download the utility.
  • Page 33 After downloading it, follow the step-by-step instructive messages to complete the driver installation. After completion of the driver installation, restart your terminal. Installing the Fingerprint Driver Please visit Posiflex official website (https://download.posiflex.com/en- global/Download/index/driver/Kiosk/Stellar_TK-2100-Series) to download the fingerprint driver. Then, follow the step-by-step instructive messages to complete the driver installation.
  • Page 34: Nfc/Rfid Reader Nr-100

     NFC/RFID Reader NR-100 Overview of the NR-100 (for TK-2111; Android-Based System) 9-Pin USB Connector NFC/RFID Reader Board Fixing Screw Hole Overview of the NR-100 (for TK-2131/2151; Windows-Based System) USB Port (Type B) NFC/RFID Reader Board Fixing Screw Hole Using the NR-100 Card Reader After installing the drivers and tools, you can start to operate the NR-100.
  • Page 35: Mounting Bracket For Specific Payment Device: Eb Series

     Mounting Bracket for Specific Payment Device: EB Series Custom Bracket for Specific Payment Device To do more installation or get more detailed information of EB series, please contact your dealer or the service team of Posiflex.

This manual is also suitable for:

Tk-2111Tk-2131Tk-2132Tk-2151Tk-2152

Table of Contents