Summary of Contents for Asus TUF Gaming F15 Series
Page 1
ASUS TUF Gaming F15 (FX507Z) series Service Guide...
Page 2
LIMITATION OF LIABILITY Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property;...
Page 3
Disclaimer ASUS is not responsible for direct, indirect, intentional or unintentional damages resulting from improper installation and operation. Safety precautions • Keep liquids or moisture away from your Notebook PC before installing or removing any components. • Ensure to place your Notebook PC on a stable surface before installing or removing any components.
Table of Contents ⚫ Service Overview ⚫ ASUS TUF Gaming F15 (FX507Z) Series Overview ⚫ Components Top View ⚫ Components Bottom View ⚫ Repair Overview ⚫ Appropriate Tools ⚫ Key Parts and Related Parts ⚫ Disassembly steps : • BASE CASE •...
Service Overview • Carefully read through this Service Guide for a look at various components of the device before performing any service and repairs. • To provide the best service, we have provided the below information for technicians from distributors and resellers to perform the complete device disassembly and assembly.
Repair Overview This chapter describes disassembly and assembly (Assemble document please look up from the last page), please follow the information provided in this section to perform the complete disassembly procedure. ◆ Precautions: Before you perform any service or repair on the notebook, please pay special attention to the cautions prevent any damages to the notebook. 1.
Appropriate Tools Please prepare and select the appropriate tools to disassemble/assemble for the ASUS TUF Gaming F15 (FX507Z) series notebook. ⧫ Alcohol 95 ⧫ Glove ⧫ Dust-free Cloth Screwdriver Please accord to different screw specification to choose different screwdriver and head.
BASE CASE Disassembly Notice Torque (kgf- Screws Spec Step 1 : Remove the screws *11pcs. Step 2 : Use the plastic blade to pry the base case. M2.5*12L(4.5,0.8) (K) #1 BK:M2.5*9.5L(4.6,0.85) (K)#1 WH:M2.5*9.5L(4.5,0.8) (K)#1 BK:M2.5*8L(4.6,0.8) (K) #1 WH:M2.5*8L(4.5,0.8) (K)#1 BK:M2.5x8L(4.5,0.9) (K)#1 WH:M2.5x8L(4.5,0.9) (K)#1 Start To avoid the bottom case hook,...
BATTERY Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Before disassembly battery connector, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to IC damage. Step 1 : Use the non-conductive pry tool to push iron sheet. Step 2 : Use the non-conductive pry tool to disconnect battery connector.
Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear off the DIMM COVER MYLAR *1pc. Step 2 : Remove the screws *2pcs. Step 3 : Remove the SSD at left side, and remove the AL FOIL and tear off the ABSORBER from SSD. Step 4 : Remove the SSD at right side, and tear off the ABSORBER from SSD.
Page 14
Assembly Notice Please be sure to pull out adapter and disconnect the battery. When installing the SSD, please keep the SSD less then 15 degrees Please use this SSD slot as first priority. with motherboard, and then insert the SSD. >15°...
Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Unlock and remove the RAM module *2pcs (red mark). Assembly Notice Step 2 : Tear off the two ABSORBERS from each of the front and back sides of the RAM, and please note that Please paste ABSORBERS on the front and back sides of the label must be paste on the RAM.
USB BD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Tear off the MYLAR (red mark) below the DDR. Screws Spec Torque (kgf-cm) Step 2 : Disconnect the USB FPC connector (yellow mark) and remove the USB FPC. Step 3 : Remove the screw *1pc and remove the USB BD.
FAN (with THERMAL MODULE and MAIN BOARD) Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the connectors *8pcs (yellow mark) and release EDP cable tape (orange mark). Screws Spec Torque (kgf-cm) Step 2 : Remove the screws *9pcs (red mark).
THERMAL MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Please follow the reverse screws numbers to remove screws *8pcs. Torque Screws Spec Step 2 : Remove the THERMAL MODULE from MB. (kgf-cm) M2*4L (5,0.8) (K) #1 Recommend that the force point is at green block, and pull up thermal module to take...
MAIN BOARD Mainboard connector placement LED/MB FFC BATTERY GPU FAN EDP CABLE KBBL FPC USB/MB FPC K/B FPC Supports using JIG BOARD to CPU FAN TP/MB FFC SPEAKER refresh F1 BIOS. Back...
Page 21
MAIN BOARD Parts marked in yellow can be ordered/replaced Materials on mainboard separately at L2 repair level. When L3/L4 repair finished, no need to paste new one if shortage of this material on the MB. TOP SIDE FX507ZE MB G20 GPU TOP ABSORBER(INTEL E SERIES) FA506IV N18E CPU ABSORBER FA506IV N18E CPU ABSORBER FX507ZE MB G20 GPU TOP ABSORBER(INTEL E SERIES)
Page 22
MAIN BOARD Parts marked in yellow can be ordered/replaced Materials on mainboard separately at L2 repair level. When L3/L4 repair finished, no need to paste new one if shortage of this material on the MB. BOT SIDE Choose by GPU/VGA CHIP Model FX507ZE MB G20 GPU BOT ABSORBER FX507ZE MB G20 GPU BOT ABSORBER Choose by GPU/VGA CHIP Model...
LED BD Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Flip the Mylar (red mark). Assembly Notice Step 2 : Release the Gasket. Step 3 : Remove the LED BD with LED FFC. If FFC is damage during disassembly, please replace new one.
TOUCHPAD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Disconnect the TP FFC connector (red mark) and remove the TP FFC. Step 2 : Release the Mylar (green mark). Screws Spec Torque (kgf-cm) Step 3 : Remove the screws *3pcs and take out the Touchpad.
SPEAKER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the SPEAKER. Assembly Notice For Speaker assembly, please follow the mark below to tidy up cable. Remove Back...
KEYBOARD MODULE Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the screws *4pcs (red mark). Screws Spec Torque (kgf-cm) Assembly Notice Step 2 : Open and remove the KEYBOARD MODULE. M2.5*5L (K) B-ZN NY #1 Please refer below picture to organize EDP cable while repair device, it’s to keep device safety.
LCD BEZEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the BEZEL COSMETIC MYLAR *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Remove the screws *2pcs. M2.5*3.5L(4.5,0.5) (K)#1 Step 3 : Remove the LCD BEZEL. Step 3-4 Due to some tapes behind the lower edge of bezel, please using plastic blade to teardown the bezel.
LCD PANEL Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Remove the screws *4pcs and remove the hinges *2pcs. Screws Spec Torque (kgf-cm) Step 2 : Pull out the LCD adhesive *2pcs. M2.5*3L (4.5,0.4) (K) #1 Step 3 : Remove the LCD PANEL.
LCD COVER Disassembly Notice Please be sure to pull out adapter and disconnect the battery. Step 1 : Release the Gasket (red mark). Step 2 : Disconnect (green mark) and remove the EDP cable. Step 3 : Use the non-conductive pry tool to insert from below and slide to the left then remove the CAMERA. Step 4 : Remove the MIC RUBBER *2pcs.
Page 30
LCD PANEL and LCD Cover Please be sure to pull out adapter and disconnect the battery. Assembly Notice Assembly Notice When replace the LCD and reuse the LCD COVER : When reuse the LCD PANEL or BEZEL : Please paste new LCD COVER TAPE *2pcs. Please use the fingertip to clean the residual glue on PANEL or BEZEL.
Page 31
LCD PANEL and LCD Cover Assembly Notice Assembly Notice Please be sure to pull out adapter and disconnect the battery. Please refer the below pictures to assemble the EDP cable : Step 1: Make sure the cable is secured to the clip as below yellow mark. Step 2: Put the hinge back in and lock screws *2pec on each side.
Need help?
Do you have a question about the TUF Gaming F15 Series and is the answer not in the manual?
Questions and answers