Advertisement

Quick Links

U S E R G U I D E
98-01624 R0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EcoStop and is the answer not in the manual?

Questions and answers

Summary of Contents for TeeJet Technologies EcoStop

  • Page 1 U S E R G U I D E 98-01624 R0...
  • Page 2: Table Of Contents

    GENERAL WARNINGS AND PRECAUTIONS CHAPTER 1 – CONNECTIONS Boom Interface Module Harness Connection ............................8 CHAPTER 2 – ECOSTOP MOBILE INTERFACE Connect to the EcoStop Mobile Interface .............................9 Verify Current Boom Configuration .................................9 Get to Work ........................................9 INITIAL STARTUP & CONFIGURATION WI-FI ACCESS CONNECTION Connect Your Apple Device ..................................
  • Page 3: Important Safety Information

    ® TeeJet Technologies IMPORTANT SAFETY INFORMATION All safety related and operating instructions should be read before the system is operated. Safe operation of machinery is the operators responsibility. Safety procedures must be posted close to the equipment and clearly visible to and legible by the operator. Safety procedures should meet all company and local regulations, as well as MSDS-requirements.
  • Page 4 ® TeeJet Technologies WARNING! PRESSURISED HYDRAULIC SYSTEMS • Always wear personal protective equipment (PPE) when performing work on hydraulic systems. • Adhere to the machine manufacture’s approved maintenance instructions when working on the hydraulic system. • Always turn equipment off when working on the hydraulic system. Take appropriate precautions when opening systems that have been previously pressurised.
  • Page 5 ® TeeJet Technologies CAUTION! HARNESS CABLE AND HOSE SAFETY • Routinely check all harness cables and hoses for damage or wear. Replace or repair when necessary. • Do not route harness cables and hoses with sharp bends. • Do not strap harness cables and hoses to lines with high vibration or spikes in pressure. •...
  • Page 6: Chapter 1 - Connections

    NOTE: Connectivity to different devices may be released with future software releases. Always refer to software release notes for software/system connectivity at www.teejet.com/support/software.aspx. POWER POWER EcoStop Drivers RXA52 Antenna EcoStop Interface Module Matrix 908 BoomPilot Interface Module (BIM) or Implement Status Module (ISM) www.teejet.com...
  • Page 7 Access EcoStop Mobile Interface to In-cab Connector 45-04091 Cable Boom Interface Module (BIM) 45-07602 Input Status Module (ISM) Mobile Device 45-04090-XXX ESIB-xxx-xxx EcoStop to TeeJet CAN Cable EcoStop Interface Module 45-09055 Deutsch 8 position EcoStop Interface ERROR 45-05971-xx to Battery +12VDC...
  • Page 8: Boom Interface Module Harness Connection

    EcoStop Boom Interface Module Harness Connection With each machine having a different possible switchbox configuration, the location to T-Tap into the valve harness cannot be specified. However, the following guidelines may provide some assistance in completing the installation. 1. Identify boom section cable that runs from the Boom Switchbox to the boom valves.
  • Page 9: Chapter 2 - Ecostop Mobile Interface

    Establish connection to the Wi-Fi access point. See "Wi-Fi Access Connection" on page 11 for details.. Using a web browser on your mobile device, go to http://ecostop.info or use the QR Code on the EcoStop Interface Module or one of the included stickers.
  • Page 10: Initial Startup & Configuration

    INITIAL STARTUP & CONFIGURATION The first time the system is powered up and the EcoStop Mobile Interface is accessed, the configuration of the boom is incomplete. 1. Connect your device to the Wi-Fi access point. See "Wi-Fi Access Connection" on page 11 for details.
  • Page 11: Wi-Fi Access Connection

    TeeJetTech 3. Disengage the Auto-Join option for the selected network in the network's information options. 4. Connect to the EcoStop Mobile Interface. Wi-Fi connection will disengage if not connected to the mobile interface within 60 seconds. When connected, Wi-Fi LED on the EcoStop Interface Module will be on.
  • Page 12: Connect Your Apple Device

    EcoStop Connect Your Apple Device How to connect your device to the EcoStop Wi-Fi network. 5. Disengage the Auto-Join option for this network in the network's Only one mobile device may connect to the EcoStop Wi-Fi information options. network at a time. It is recommended that any automatic joining option be disabled.
  • Page 13: Connect Your Android Device

    EcoStop Connect Your Android Device How to connect your device to the EcoStop Wi-Fi network. 5. Enter the network's password: TeeJetTech Only one mobile device may connect to the EcoStop Wi-Fi 6. Disengage the Auto-Join option for this network in the network's network at a time.
  • Page 14: Configure

    EcoStop CONFIGURE Establish and adjust the boom configuration on the Configure screen  1. Set the Number of Sections using the Decrease/Increase buttons 2. Set the Nozzles per Section. W Select the Section Number to be configured using the Decrease/Increase ...
  • Page 15: Work

    EcoStop WORK Start and stop sections on the Work screen Control All Sections  1. Use the Start/Stop All Sections buttons to control all sections Control an Individual Section  1. Set the Individual Section using the Decrease/Increase buttons ...
  • Page 16: About

    EcoStop ABOUT The About screen displays current software version for the EcoStop Mobile Interface and accesses software update options. Software updates will be made available at www.teejet.com as needed. Software Updates 1. Follow the on screen instructions. 2. Once receiving the "Firmware update complete" screen, restart the system to ensure boom information is reported correctly.
  • Page 17: Exit

    The Mobile Interface will automatically disconnect from the EcoStop Wi-Fi network after five minutes of inactivity. Closing the web browser will not disconnect the EcoStop Wi-Fi network. Control is returned to the switchbox and the Mobile Interface will disconnect from the network after one minute of inactivity.
  • Page 18: Appendix A - Module & Driver Led Information

    EcoStop APPENDIX A – MODULE & DRIVER LED INFORMATION ECOSTOP INTERFACE MODULE LED: Wi-Fi Status LED. • Off: No Wi-Fi connection. • On: Wi-Fi connection. • Blinking at 2 Hz: Wi-Fi communication active. LED: COM Interface to PLP Controller CAN Bus Status LED.
  • Page 19: Ecostop Driver

    EcoStop ECOSTOP DRIVER LED: V (Volts) Module Voltage Status LED. • Off: Module voltage within high and low limits. • Default high limit: 16.0 V • Default low limit: 11.0 V • Blinking at 6 Hz for high limit error.
  • Page 20 EcoStop Mobile Interface. Copyrights © 2024 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described in it may be reproduced, copied, photocopied, translated, or reduced in any form or by any means, electronic or machine readable, recording or otherwise, without prior written consent from TeeJet Technologies.

Table of Contents