Subscribe to Our Youtube Channel
Related Manuals for TeeJet Technologies DynaJet Flex Series
Summary of Contents for TeeJet Technologies DynaJet Flex Series
- Page 1 D Y N A J E T ® F L E X INSTALLATION, SETUP AND USER GUIDE Software version 1.02 with optional high flow option...
- Page 2 Copyrights © 2016 TeeJet Technologies. All rights reserved. No part of this document or the computer programs described in it may be reproduced, copied, photocopied, translated, or reduced in any form or by any means, electronic or machine readable, recording or otherwise, without prior written consent from TeeJet Technologies.
-
Page 3: Table Of Contents
Table of Contents DYNAJET® FLEX OVERVIEW INSTALLATION CONSOLE INSTALLATION – STANDARD MODE DynaJet® drivers ......................................3 Power ..........................................3 Nozzle harnesses ......................................3 Pressure sensor interface kit ..................................4 Boom interface module (BIM) ..................................4 DynaJet® interface ......................................4 CAN cables and terminators ..................................4 INSTALLATION – HIGH FLOW MODE DynaJet®... -
Page 4: Dynajet® Flex Overview
Standard RAM bracket Safety information TeeJet Technologies is not responsible for damage or physical harm caused by failure to adhere to the following safety requirements. As the operator of the vehicle, you are responsible for its safe operation. - Page 5 DynaJet Flex ® Figure 3: System diagram - standard mode 98-05334-EN R2...
-
Page 6: Installation - Standard Mode
DynaJet Flex ® INSTALLATION – STANDARD MODE DynaJet® drivers Nozzle harnesses There will be one DynaJet driver 78-05122 per boom section with a When installing nozzle harnesses 45-05935-xx-xx always start with limit of 20 nozzles per section. section 1 and continue to the last section. •... -
Page 7: Pressure Sensor Interface Kit
DynaJet Flex ® Pressure sensor interface kit DynaJet® interface The DynaJet system requires pressure sensor interface kit 90-04007 The DynaJet interface 78-05106 connects to the Sentry interface or 98-04008 to be installed. harness 45-10148: • The pressure sensor interface kit should be mounted close to The Sentry interface harness connects to the boom manifold. -
Page 8: Installation - High Flow Mode
TeeJet customer service representative for clarification before installation. TeeJet technologies is not responsible for misuse or incorrect installation of the system. - Page 9 DynaJet Flex ® Figure 4: System diagram - high flow mode 98-05334-EN R2...
- Page 10 DynaJet Flex ® Item Part # Description Illustration 90-02887 DynaJet 7120 console 45-05900: 1.5 m Console extension cable 45-05901: 3 m 45-05902: 6 m 45-05903: 12 m 45-10177 DynaJet interface harness 78-05123 DynaJet HF interface 45-05857: 1 m CAN extension cable 45-05858: 2 m 45-05859: 4 m 45-05864: 10.5 m...
-
Page 11: Initial Startup
DynaJet Flex ® INITIAL STARTUP This section will explain basic setup of the values required for first-time setup of a DynaJet Flex system. When these settings are completed, initial operation and fine-tuning should be possible. To access setup menu from the work screen, touch center of the screen. 1. -
Page 12: Units
DynaJet Flex ® Units Nozzle selection Sets the units to us (PSI) or metric (bar) Accesses the nozzle selection process to select which nozzle is to be used. At this time only TeeJet nozzles are supported. Figure 8: Units Figure 11: Nozzle selection Number of sections Set the number of boom sections. -
Page 13: Ready To Pressure Test The System
DynaJet Flex ® Ready to pressure test the system 1. Ensure that current rate control system is operating at the 4. Switch the master switch ON (on rate control or other boom optimum level. Set DynaJet operating mode to manual and set section control switches) and individual sections one at a time PWM duty cycle at 100%. -
Page 14: User Settings
DynaJet Flex ® USER SETTINGS Figure 14: Work screen - standard mode If there are questions concerning the setup of the Current droplet size PWM duty cycle Actual pressure DynaJet Flex, please contact your dealer or TeeJet customer service representative for clarification before operation. TeeJet technologies is not responsible for misuse or incorrect operation of the system. - Page 15 DynaJet Flex ® Number of nozzles (high flow mode only) Fine gain Set the number of nozzle locations for each boom section. Allows the control system to make minor adjustments when close to Range is 1 to 120. the target, with the goal of stable pressures and minimal overshoot of target.
-
Page 16: Oem Settings
DynaJet Flex system. Do not adjustments to pressure regulation. Once coarse gain has alter these settings unless directed by TeeJet Technologies support brought pressure near target; coarse gain off and fine gain will personnel. -
Page 17: Dynajet® Nozzle Selection
DynaJet Flex ® DYNAJET® NOZZLE SELECTION Selection of the proper spray nozzle for use with the DynaJet system is much like selecting the spray nozzle for a traditional spraying operation. Along with the extra application flexibility, DynaJet brings a few other nozzle-related considerations that will be summarized below. 1. -
Page 18: Nozzle Selection Example
DynaJet Flex ® Nozzle selection example These columns show flow rates at various These columns show droplet sizes pressures. The Delta P represents pressure loss for different styles of spray nozzle at Just like a normal nozzle chart, these columns show rates through the DynaJet solenoid valve, and the given pressures. -
Page 19: 55295 E-Chemsaver® Maintenance Instructions
DynaJet Flex ® 55295 E-CHEMSAVER® MAINTENANCE INSTRUCTIONS The 55295 e-ChemSaver is a solenoid-actuated shutoff compatible with a wide range of TeeJet nozzle bodies equipped with a diaphragm check valve. It can be used for end-of-boom nozzles as well as individual nozzle shutoff and PWM controls. The valve is normally closed and opens when the solenoid is energized. -
Page 20: Application Rates At Given Speed
DynaJet Flex ® www.teejet.com... - Page 21 DynaJet Flex ® 98-05334-EN R2...
- Page 24 PWM control of each nozzle delivers very large ranges of speeds and application rates with a single spray nozzle and with consistent spray quality. www.teejet.com 98-05334-EN-A4 R2 English © TeeJet Technologies 2016...
Need help?
Do you have a question about the DynaJet Flex Series and is the answer not in the manual?
Questions and answers