Subscribe to Our Youtube Channel
Related Manuals for Racing RAC2500ESH-3
Summary of Contents for Racing RAC2500ESH-3
- Page 1 ORIGINAL INSTRUCTIONS >EN ELECTRIC PLANT SHREDDER RAC2500ESH-3 USER GUIDE CAUTION: Read this manual before using this machine!
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS........................3 2. PARTS LIST............................14 3. CHARACTERISTICS.......................... 14 4. ASSEMBLY............................15 5. BEFORE USE THE PRODUCT......................15 6. OPERATION............................17 7. MAINTENANCE AND STORAGE....................18 8. DISPOSAL............................19 9. DECLARATION OF CONFORMITY....................20 10. WARRANTY............................21 11. PRODUCT FAILURE........................22 12. WARRANTY EXCLUSIONS......................23... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS Before using this product, carefully read and understand all the safety recommendations instructions for safe operation. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Keep this manual handy so that you may refer to it later whenever any questions arise. - Page 4 1. Never operate this product when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. Keep in mind, that the operator or user is responsible for accidents or hazards occurring to other people or their property.
- Page 5 4. Never start working until you have a clear work area, and secure footing, 5. Keep all parts of your body away from the feeding opening when the engine is running. 6. Before you start the product, make sure the product is properly assembled and that insertion chamber is not obstructed.
- Page 6 13.3. Do not force the tool. It will do the job better and safer at the rate speed for which it is intended. The product will do a better and safer job if it is used only for the purposes it was designed for. 13.4.
- Page 7 1.2- Safety precautions 1.2.1- Initial preparation before operation - When you operate the machine, always wear full-length trousers, as well as sturdy, closed footwear that provide good support. Do NOT operate the machine wearing shorts, when barefoot or wearing open sandals! - Do not wear loose clothing or jewellery that can be drawn into the inlet.
- Page 8 are in perfect working order. Any damaged or defective components should be repaired immediately by a qualified technician. Never attempt to use an incomplete, not fully assembled or modified machine. - Under no circumstances or if safety equipment such as collection box is not installed, before using, always visually inspect to see, that the shredding means, shredding means bolts and other fasteners are secure,...
- Page 9 DISCONNECTING THE SUPPLY CORD FROM ITS POWER SOURCE. - If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. - Do not carry the appliance by the cable. Never use the power cord as a handle to lift or carry the device.
- Page 10 grass. - Do NOT use the machine on slope areas. - Keep the chute outlet and ventilation holes (cooling air inlets) unobstructed, clear of debris and clean at all times. - Do not assume of your knowledge of the machine. Remember that a split second of negligence is sufficient cause serious...
- Page 11 Keep the power source clean of debris and other accumulations to prevent damage to the power source or possible fire. Do not transport this machine while the power source is running. Stop the machine, and remove plug from the socket. Make sure that all moving parts have come to a complete stop.
- Page 12 - Check the debris collection box frequently for signs of wear and/or deterioration. - Replace any worn or damaged parts. - Make sure to use only genuine/original replacement parts and accessories. - For reasons of safety, any worn or damaged component should be replaced or repaired immediately by a qualified technician.
- Page 13 (i.e. the appliance should be supplied via a Residual Current Device (RCD) with a tripping current of not more than 30mA). 1.3- Explanation of Symbols Do not expose to weather conditions (ex.: rain, snow …) or to moisture. Do not use nor leave outdoor during weather conditions (e.g. rain, snow…) Do not use in the rain or leave outdoors while it is raining.
-
Page 14: Parts List
2. PARTS LIST 1. Feed hopper 2. Shredder body 3. Motor cover 4. Collection box 5. Frame 6. Wheel 7. .Feet 8. Main switch 9. Circuit breaker 10. Cover knob 3. CHARACTERISTICS Voltage 230-240 V ~ 50 Hz Power 2500W(P40) No load speed n 4050 min Insulation protection class... -
Page 15: Assembly
4. ASSEMBLY Fig 3 Fig 4 Fig 5 Fig 7 1.Turn on the Foot A and Food B to the appropriate location (Fig.3) ,then upside down the machine. 2. Mount the wheel in the same order illustrated in fig 5 ensure the nut is not too tight. 3. - Page 16 1. Inspect the material to be shredded before starting. Remove any objects or debris that could be thrown, jammed or become entangled in the blades. Remove any soil from root balls. Foreign bodies like stones, glass, metals, fabrics, or plastics must not enter the in-feed chute, these could damage the blades.
-
Page 17: Operation
6. OPERATION Starting and Stopping the shredder Press the switch marked “1” to start and marked “0” to stop the motor. Press the “circuit breaker” button if the machine does not work, ensure you have connected to the power supply. When the motor has been running for a few seconds you can commence shredding. -
Page 18: Maintenance And Storage
HOW DO I COLLECT THE SHREDDED MATERIAL Shut-off the power unit before attaching or removing the bag. You can use either the collection bag supplied (if supplied) or place the shredder on a tarpaulin sheet to catch the shredded material. When using the collection bag, you need to fit the collection bag hooks onto the sides of the discharge chute Warning: The ventilation slots on the machine body must never be covered by the collection... -
Page 19: Disposal
hand. 6. Never attempt to override the interlock feature of the guarding. 7. Remove deposited matter from the machine using a brush. 8. Always clean the machine after use. Clean the plastic body and plastic parts using soap and a moist cloth. -
Page 20: Declaration Of Conformity
BUILDER SAS ZI, 32 rue aristide Bergès – 31270 Cugnaux - France Declares that the machinery designated below: ELECTRIC PLANT SHREDDER RAC2500ESH-3 Serial number: 20240515637-20240515916 Complies with the provisions of the Directive “machinery” 2006/42/EC and national laws transposing it: Also complies with the following European directives:... -
Page 21: Warranty
10. WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. It can be extended by one year if the user subscribes to website of myswap. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. -
Page 22: Product Failure
11. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: • Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. •... -
Page 23: Warranty Exclusions
12. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •... - Page 24 BUILDER SAS 32 rue Aristide Bergès - Z.I. du Casque - 31270 Cugnaux - France MADE IN PRC...
Need help?
Do you have a question about the RAC2500ESH-3 and is the answer not in the manual?
Questions and answers