Toro GrandStand 74527 Setup Instructions
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. GrandStand 74527
  6. Setup instructions
Toro GrandStand 74527 Setup Instructions

Toro GrandStand 74527 Setup Instructions

Multi force snow machine
Hide thumbs Also See for GrandStand 74527:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

GrandStand
Model No. 74527—Serial No. 4000000000 and Up
This product contains a chemical or chemicals known to the State of California to
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Multi Force Snow Machine
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
No parts required
Operator's Manual
Engine owner's manual
Registration card
Key
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
–
–
–
–
–
–
1
1
1
2
Form No. 3408-597 Rev A
Setup Instructions
Use
Check the tire pressure.
Check the engine-oil level.
Add fuel to the machine.
Check the hydraulic-fluid level.
Charge the battery.
Install the battery cables.
Check the machine before delivery to
the customer.
Deliver the machine to the customer.
Original Instructions (EN)
All Rights Reserved *3408-597* A
Printed in the USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GrandStand 74527 and is the answer not in the manual?

Questions and answers

Related Manuals for Toro GrandStand 74527

Summary of Contents for Toro GrandStand 74527

  • Page 1 No parts required the customer. Operator's Manual Engine owner's manual Deliver the machine to the customer. Registration card © 2016—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3408-597* A 8111 Lyndale Avenue South Printed in the USA...

  • Page 2: Checking The Tire Pressure

    Checking the Tire Pressure Adding Fuel to the Machine No Parts Required No Parts Required Procedure Procedure Pressure: 83 to 97 kPa (12 to 14 psi) Add fuel to the machine before starting it. Refer to your Operator’s Manual for the correct fuel and procedure. Note: The front caster wheel is a semi-pneumatic tire and Note: Ensure that the fuel-shutoff valve is open before does not need to be checked.

  • Page 3: Charging The Battery

    Charging the Battery Installing the Battery Cables No Parts Required No Parts Required Procedure Procedure Install the positive battery cable, then install the negative WARNING battery cable (Figure CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
  • Page 4 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure.
  • Page 5 Set Up Instructions. Make sure that the customer knows the Parts Catalog and operator-training materials are available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provided below and keep a copy of this page for dealer records.
  • Page 6 Notes:...
  • Page 7 Notes:...

Table of Contents