NETZSCH Max-Shear Instruction Manual
  1. Manuals
  2. Brands
  3. NETZSCH Manuals
  4. Laboratory Equipment
  5. Max-Shear
  6. Instruction manual

NETZSCH Max-Shear Instruction Manual

Inline disperser
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Table of Contents
Instruction Manual
Max-Shear Inline Disperser
Read and understand this manual prior to
operating or servicing this product.
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Max-Shear and is the answer not in the manual?

Questions and answers

Related Manuals for NETZSCH Max-Shear

Summary of Contents for NETZSCH Max-Shear

  • Page 1 Table of Contents Instruction Manual Max-Shear Inline Disperser Read and understand this manual prior to operating or servicing this product. Page 1...
  • Page 2 NETZSCH Premier Technologies, LLC. assumes no liability or responsibility for product loss, damage to plant and equipment, or personnel injury that may arise from the use of the information in this document. Nor warranties of merchantability or fitness for purpose shall apply.

  • Page 3: Table Of Contents

    Table of Contents Introduction ........................6 Installation ......................... 6 Utility Requirements ....................6 Piping and Pl umbi ng ......................6 Electrical Connecti ons ......................6 Mechanical Seals (Two Options) ................6 Single Mechanical Seal ....................... 6 Double Mechanic al Seal ..................... 6 Start-Up Procedure .....................
  • Page 4 Products covered by an Order. In the event of sales of goods and servi c es (“Products”) made or provided by any such change, the Buyer shall pay to the Company the NETZSCH Premier Technologies, LLC (the “Company”) to any reasonable costs...
  • Page 5 Terms & Conditions any item or items made or handled by the Products supplied wearing parts are excluded from the foregoing warranty and hereunder, including any such Losses based in whole or in part are provided “as is, where i s ”. on the default or negligence of the Company.

  • Page 6: Introduction

    The Max-Shear Disperser is also recognized for its pum ping abilit y. In many applications, the Max-S hear Disperser can blend and pump without requiring additional equipment.

  • Page 7: Start-Up Procedure

    Dispers er’s pum ping ability. Cavitation is a condition that exists when the s uction requirem ents of the Max-Shear are not met. This can be c aused by too many elbows in the Max -Shear suction line or incorrect suction pipe size contributing to friction loss es.

  • Page 8: Cleaning

    Special seals and bearings may be necessary if the product discharge pressure exceeds 50 psig (3.33 bar). Clean the Max-Shear Disperser after each use. Aqueous-based Cleaning dispersions can be flus hed wit h water. Non-aqueous -based dispersions can be flushed with a suitable solvent.

  • Page 9: Belt Drive Option

    Netzsch Premier Technologies, LLC. Belt Drive Option Timing Belt Disconnect the electrical power, remove t he pulley guard, and adjust by loosening the motor mounts. Move t he motor closer to t he disperser to decrease tension or farther from the disperser to increase tension. Over- tensioning the timing belt can damage the bearings.

  • Page 10: Units W Ith Single Mechanical Seals

    Protect the seal face from abrasive surfaces, which c ould nick or break the seal face. Max-Shear 6" and 8" sizes: Remove the s eal housing mounting plate. The primary stationary seal face is locat ed in the mounting plate. Us e care when disassembling. Protect the s eal face from abrasive surfaces that could nick or break the seal face.

  • Page 11: Reassembly

    Netzsch Premier Technologies, LLC. Thoroughly clean and inspect all components before starting the Reassembly assembly procedure, and replace any questionable components. Reassem bl e the unit by reversing the di sassembl y procedure. NOTE : It is important that the seal area be clean and free of 1.

Table of Contents