Frigidaire FAC124P1A Use And Care Manual

Frigidaire FAC124P1A Use And Care Manual

Multi-step speed electronic control
Hide thumbs Also See for FAC124P1A:

Advertisement

THIS AIR CONDITIONER
IS EQUIPPED WITH A NEW INDUSTRY
STANDARD
POWER SUPPLY CORD WITH A TEST-RESET
FUNCTION
READ AND SAVE THESE INSTRUCTIONS
MULTi-STEP
SPEED ELECTRONIC
CONTROL
P/N 220201d011

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FAC124P1A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Frigidaire FAC124P1A

  • Page 1 THIS AIR CONDITIONER IS EQUIPPED WITH A NEW INDUSTRY STANDARD POWER SUPPLY CORD WITH A TEST-RESET FUNCTION READ AND SAVE THESE INSTRUCTIONS MULTi-STEP SPEED ELECTRONIC CONTROL P/N 220201d011...
  • Page 2 The date on the bill establishes the warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order: 1.
  • Page 3 Product Registration Record Your Model and Serial Numbers Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the outside of the cabinet. Model No. Serial No. Register Your Product...
  • Page 4 Safety Instructions For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance= Read product labels for flammability and other warnings= The power supply cord with this air conditioner...
  • Page 5 Always make sure the RESET button is pushed in for correct operation. • The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.
  • Page 6 TO CHANGE TEMPERATURE YOU WILL SEE: SETTING: Note: Tap or hold either up( A ) or down( V ) button until the desired temperature is seen on the display. This temperature DO THINS: wiII be automatically maintained anywhere between 60°F (16°C) ÷...
  • Page 7 FEATURE: YOU WILL SEE: LIGHT On Note: In this mode, the fan will continue to run for 3 minutes after the DO THIS: compressor shuts off, The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature...
  • Page 8 Note: For Delay Start, the unit must be in the Off position. PRESS TIMER BUTTON To adiust timer setting, tap or hold the UP arrow(A) or the DOWN arrow(V) to change delay timer at =5hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.).
  • Page 9 ,A ,_ buttons to set the desired temperature at the remote. (Note that the set temperature wilI only be displayed on the unit itself). The LIGHT on the unit control wilI pulse to DO TH_S: indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal.
  • Page 10 Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with= • The "Cool "circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping.
  • Page 11 Auger Type The louvers will allow you to direct tile air flow Up or Down and Left or Right throughout the room as needed. Rotate the Auger Wheels until the desired Left/Right direction is obtained. Pivot horizontal louvers until the desired Up/Down direction is obtained.
  • Page 12 60'F (18':C). To defrost the coil, set FAN ONLY Mode. too warm - ice forming on cooming Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY Mode. coil behind decorative front.

Table of Contents