Dual MGH17BT - Hole Receiver Manual

Also See for MGH17BT:

Advertisement

Dual MGH17BT - Hole Receiver Manual

Mounting & Wiring

Once a suitable location has been determined, drill the hole and secure the stereo using the metal mounting bracket. If the bracket needs to be shortened, remove the appropriate number of breakaway segments using a pair of pliers.
Mounting & Wiring

Color Connection
Red 12V Ignition / Accessory
Black Ground
Blue Remote Turn-on B (+)
Grey Right Front (+)
Grey/Black Right Front (-)
White Left Front (+)
White/Black Left Front (-)
Violet Right Rear (+)
Violet/Black Right Rear (-)
Green Left Rear (+)
Yellow Camera Input(RCA Type)
Green/Black Left Rear (-)
Connectors used

Tip:
When a suitable ground wire is not present in the vehicle wiring harness, connect the black ground wire to the vehicle chassis.

Fuse:
When replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio.

Installation

Device Installation
Mounting the Radio

  1. Choose a mounting location on the dash board or instrument panel that will allow room behind to run radio cables to the power source. Consider how you will use the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables to an accessible area.
  2. Cut a hole in the dash board using the template provided in the back of this manual. At least 3 3/4" depth is needed to mount the radio.


Do not mount this unit where it can be submerged in water.

  1. Slide the included spring washers (B) over the screw posts (A) and attach the screw posts to the back of the radio.
  2. Place the radio in front of the dashboard opening so the wiring can be brought through the opening.
  3. After completing the wiring connections, turn the radio on to confirm operation (vehicle accessory switch must be on). If the radio does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the accessory switch off and proceed with final mounting of the radio. Refer to the "Wiring Diagram".
    NOTE: Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.
  4. Insert the radio into the mounting hole.
  5. Place the "U" bracket (C) over the screw posts and secure the radio to the dash using the included hex nuts (D). If necessary, cut the score marks (E) on either side of the mounting bracket to custom fit the bracket length for your application. See Figure A.

General Operation

Power On/Off Press the button to turn the unit on. Press and hold to turn unit off.
Changing Modes Press MODE to select between AM/FM, auxiliary, USB and operation of iPod/iPhone. Modes of operation are shown in the display.
Volume Adjust volume using volume up/down key.
Mute Press to silence the audio. Press again to resume listening at the previously selected volume.
Auxiliary Inputs Insert RCA cables into the rear AUX-IN connectors.
Display Press DISP to toggle display between various displayed information.
Menu Press MENU to access the audio and setup menu options.
Reset If abnormal operation occurs, press and hold MENU and TUNE factory settings. nn for 3 seconds to reset the unit to the default

AM/FM Tuner Operation

Seek Tuning Press TUNE or TUNE second to seek to the next strong station. ll for more than one
Manual Tuning Press TUNE or TUNE radio frequency up or down one step at a time. Press ll momentarily to move and hold to advance quickly.
Band Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.
Storing Presets Select the desired band and station. Hold the P button, turn the volume up/down key until the desired preset number is highlighted, then press SELECT to store the preset.
Recalling Presets Press the P buttons to cycle through the 1-6 presets in the current band.

MP3 Operation

Playing MP3 Files To play MP3 files, insert a USB device containing MP3 files.
Track Select Press TUNE to skip to the beginning of the next song. Press TUNE to return to the beginning of the current song. Pressing TUNE the previous song. nn again skips to the beginning of
Fast Forward and Reverse Press and hold TUNE or TUNE to fast forward or reverse a track.
Pause Press to temporarily stop playback.
Press again to resume playback.
Folder Access Press to select the next folder. Press to select the previous folder. Folder access is only available on devices with more than one folder.
Repeat Press BAND to enter the Repeat menu, then turn the volume up/down key to select one of the following options:
  • Current Song - Continuously repeats selected track.
  • Current Folder - Continuously repeats all files in folder.
Random Press BAND to enter the Random menu, then turn the volume up/down key to select one of the following options:
  • Off - Cancels RDM function.
  • All Songs - Plays all tracks in random order.
  • Current Folder - Plays all tracks in folder in random order
Intro Press BAND to enter the Intro menu, then turn the volume up/down key to select one of the following options:
  • Off - Cancels the INT function.
  • All Songs - Plays first 10 seconds of each track.
  • Current Folder - Plays first 10 seconds of each track in the selected folder.

* Not available on all models.

Operation of iPod/iPhone

Connect an iPod/ iPhone Device (sold separately) To play music from an iPod/iPhone device, connect the USB cable (included with your iPod/iPhone device) to the unit's USB port. Playback will begin automatically.
Song Select Press ll to skip to the next song. Press to return to the beginning of the current song. Pressing again skips to the beginning of the previous song.
Forward/Reverse Press and hold or to fast forward or reverse.
Pause Press to temporarily stop playback.
Press again to resume playback.
Repeat Press BAND to enter the Repeat menu, then turn the volume up/down key to select one of the following options:
  • Off - Repeats all tracks.
  • Current Song - Repeats selected track.
Random Press BAND to enter the Random menu, then turn the volume up/down key to select one of the following options:
  • Off - Cancels the RDM function.
  • All Songs - Plays all tracks in random order.
  • Current Album - Plays all tracks in the selected album in random order.
Intro Press BAND to enter the Intro menu, then turn the volume up/down key to select one of the following options:
  • OFF - Cancels the INT function.
  • ON - Plays first 10 seconds of each track.
Music Search Turn the volume up/down key to select between artists, albums, songs, playlists, podcasts and audiobooks. Press SELECT to select the desired search category. Most search categories have subcategories to navigate through.
Manual Control for iPod When "MANUAL" control is selected from the Setup Menu, the iPod or iPhone device can be controlled directly from the device's interface. All functions except for volume can be used from the iPod or iPhone device. Note: The firmware of the iPod/iPhone must be up dated to the latest version to be compatible with manual control model. Not all devices are compatible with manual control mode.

* Not available on all models.

Bluetooth Operation

Preparation Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.
Pairing a New Device The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner's manual for your device for more details.
The device name is "MGH17BT"
The Bluetooth passcode is "1234"
Note: The head unit can be in any mode of operation when pairing is performed.
Pairing Additional Devices If a device is currently connected, press and hold BAND to disconnect the current device before a new device can be paired. Then begin the pairing sequence from the new Bluetooth device.
Disconnecting a Device Press and hold BAND for 3 seconds to disconnect a connected device. The device will remain paired and appear in the SEARCH menu, but not be connected.
Bluetooth Reset Resetting the Bluetooth module will remove the list of paired phones. Reset Bluetooth as follows:
  1. Press MODE until the head unit is in Bluetooth mode.
  2. Press and hold MENU for 3 seconds to reset the Bluetooth settings back to the factory default.
Streaming Audio Troubleshooting The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:
  • Press to skip to the next available audio track.
  • Press to skip to the previous audio track.
  • Press to toggle between play and pause during playback.

* Not available on all models.

Weather Band Operation

Manual Tuning Press TUNE or TUNE momentarily to seek the next weather band station.
Band Press BAND to select weather band(WB).

* Not available on all models.

Limited One-Year Warranty

What to do?

  1. Before you call for service, check the troubleshooting guide in your owner's manual. A slight adjustment of any custom controls may save you a service call.
  2. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.
  3. For more information and for the location of the nearest authorized service center please contact us toll-free at 1-866-382-5476 or by email at cs@dualav.com.

Dual Electronics Corp.
Toll Free: 1-866-382-5476
Monday-Friday, 9AM-5PM
www.dualav.com

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Dual MGH17BT - Hole Receiver Manual

Advertisement

Need help?

Need help?

Do you have a question about the MGH17BT and is the answer not in the manual?

Questions and answers

Table of Contents