1. Manuals
  2. Brands
  3. Erskine Attachments Manuals
  4. Planer
  5. CP18A
  6. Operator's manual

Erskine Attachments CP18A Operator's Manual

Cold planer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
COLD PLANER
CP18A
CP24A

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CP18A and is the answer not in the manual?

Questions and answers

Related Manuals for Erskine Attachments CP18A

Summary of Contents for Erskine Attachments CP18A

  • Page 1 COLD PLANER CP18A CP24A...
  • Page 2 TO THE DEALER: ® Assembly and proper installation of this product is the responsibility of the Erskine dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manual are completed before releasing equipment to the owner.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..........2 SPECIFICATIONS .

  • Page 4: Introduction

    SPECIFICATIONS CP18A CP24A Planing Width 18" (457mm) 24" (610mm) Planing Depth 0 - 6" (0-152mm) 0 - 6" (0 - 152mm) Hyd Horsepower 30 - 65 hp (22.4-48.5 kw) 33 - 65 hp (24.6-48.5 kw) Sideshift Capability 22" (559 mm) 22"...

  • Page 5: Safety Rules

    SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! grene, serious injury, or death will result. CON- Safety is a primary concern in the design and TACT A P HYS ICIA N IM ME DIATE LY IF FLU ID manufacture of our products. Unfortunately, our ENTERS SKIN OR EYES.
  • Page 6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Be sure attachment is properly secured, Do not operate or transport equipment while adjusted, and in good operating condition. Coupler under the influence of alcohol or drugs. lockpins must be fully extended and properly Operate only in daylight or good artificial light.
  • Page 7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! or between moveable parts even when the engine lockpins must be fully extended and properly has been turned off. Hydraulic system leak-down, engaged into attachment retaining slots. hydraulic system failures, mechanical failures, or Never perform service or maintenance with movement of control levers can cause equipment engine running.
  • Page 8 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! Serial Number Plate D0193 WARNING ROTATING CUTTER Keep clear during operation. See Operator's Manual for maintenance precautions. D0193 D0195 DO209 WARNING WARNING FLYING OBJECT FLYING OBJECT HAZARD HAZARD Keep clear during...
  • Page 9 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 54519 WARNING FALLING OFF CAN RESULT IN BEING RUN OVER. Skid steer must have ROPS and seat belt/operator restraint. Keep seat belt/operator restraint securely fastened. Allow no riders.

  • Page 10: Safety Decals

    OPERATION SAFETY PRECAUTIONS SETUP ARNING Accidents are preventable with your help. ARNING ■ Read the entire manual as well as the decals on the attachment (see safety section) before attempt- ing any maintenance, service, repair or setup of the ■ Before operating this equipment, the following unit.

  • Page 11: Operation 11

    arms should never be placed in the float condition; depending upon how it is used and operated. There- because, excessive vibration will result. fore, the recommended operating procedures con- tained within this manual should be followed at all times With the rear gauge wheel(s) set for acceptable planing for maximum productivity.

  • Page 12: Maintenance

    MAINTENANCE IMPORTANT Proper maintenance of the attachment will result in longer life and the most productive and cost effective ■ To prevent the picks from seizing in the hold- operation. There are two basic categories of mainte- ers, the picks should be sprayed with diesel fuel at nance required, pick/holder replacement and compo- the end of each day.
  • Page 13 ● ● Remove the remainder using a low-pressure water Inspect machine and replace worn or damaged spray. parts. ● 1. Be careful when spraying near scratched or torn Sand down scratches and the edges of areas of safety decals or near edges of decals as water missing paint and coat with spray paint of matching spray can peel decal off surface.

  • Page 14: Service

    SERVICE PLANETARY REMOVAL ARNING 1. Remove the drum from the attachment as described on the previous page. ■ BEFORE SERVICING THIS UNIT, THE MANDA- 2. Fully support the planetary with hoist and remove TORY SAFETY SHUTDOWN PROCEDURE MUST the planetary flange mounting nuts. BE COMPLETED.
  • Page 15 DEALER CHECK LISTS PRE-DELIVERY CHECK LIST DELIVERY CHECK LIST (Dealer’s Responsibility) (Dealer’s Responsibility) ___ Show customer how to make adjustments. Inspect the equipment thoroughly prior to delivery to ensure it is set up properly before delivering it to the ___ Point out the safety decals. Explain their meaning customer.

  • Page 16: Trouble-Shooting

    TROUBLESHOOTING CHART PROBLEM POSSIBLE CAUSE SOLUTION Planer loses power Relief setting in auxiliary system Remove/clean, or replace sole- lower than standard 2400 psi noid cartridge or replace O-rings. Check reliefs in the following Loader circuit pump or auxiliary sequence- loader valve, standard pump failure auxiliary valve.
  • Page 17 PARTS INDEX Cold Planer for Single Circuit Valve "A" Series Skid Steer CPA SINGLE CIRCUIT PLANER ........18 CPA SINGLE CIRCUIT PLANER PARTS LIST .
  • Page 18 REF PART DESCRIPTION C0801 Cylinder, hydraulic 1.5 x 8 ----- Attach frame 101700-1 Backplate weld, CP18A 3/8 NC x 1 HHCS GR5 ZP 101702 Backplate weld, CP24A C2201 Cylinder, hyd 2 x 22 without depth 104027 Pin, 1 x 6 x 5.25 M0003 13 Retaining ring, 1"...
  • Page 19 Pin weld 1 x 8.31 SR 7.8 H1414 Hose #6 x 76" 6 SLF x 6SLF R1 32 102670418 Drum Assy, CP18A 48 holders M0005 Stud, 9/16 x 2 9/16 - 18 plntry 32 102670424 Drum Assy, CP24A 62 holders...
  • Page 20 SINGLE CIRCUIT VALVE 20 Parts MAN0831 (05/12/2010)
  • Page 21 SINGLE CIRCUIT VALVE PARTS LIST PART DESCRIPTION PART DESCRIPTION ° F 2 3 i t t i n g , # 8 O M X 6 F L M 4 5 H C 4 2 o t o r , a t o n 3 5 °...
  • Page 22 ELECTRICAL SCHEMATIC 22 Parts MAN0831 (05/12/2010)
  • Page 23 FITTING TORQUE CHART Always tighten fittings to these values unless a different torque value is listed for a specific service procedure. Make sure fastener threads are clean and threads are engaged properly. All torque values are adopted from SAE J514 and SAE J1453. SAE (JIC) O-Ring Style 37°...

  • Page 24: Bolt Torque Chart

    BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
  • Page 25 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa............Mega Pascal ASABE....
  • Page 26 WARRANTY Please enter information below and save for future reference. Date Purchased: ______________________ From (Dealer): _________________________ Model Number: ______________________ Serial Number: _________________________ Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER.
  • Page 27 WARRANTY for Replacement Parts Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.
  • Page 28 PART NO. MAN0831 ERSKINE Attachments LLC PO Box 1083 Alexandria, MN 56308 800-437-6912 tel © 2013 ERSKINE Attachments LLC All rights reserved.

This manual is also suitable for:

Cp24a

Table of Contents