1. Manuals
  2. Brands
  3. ETL Manuals
  4. Safes
  5. SECURELOGIC Wall Vault 20700
  6. Manual

ETL SECURELOGIC Wall Vault 20700 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
®

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SECURELOGIC Wall Vault 20700 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ETL SECURELOGIC Wall Vault 20700

Summary of Contents for ETL SECURELOGIC Wall Vault 20700

  • Page 1 ®...
  • Page 2 Do not store your keys or the instruction guide inside your SecureLogic Wall Vault in case you should ever need them while your Wall Vault is locked. ETL® *Due to continuous product improvements, the actual product may differ from photos.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Warnings & Recommendations pg. 3 Standard Features pg. 5 Installation Instructions pg. 7 Programming Model 20700 pg. 9 Programming Model 20710 pg. 12 Operating Instructions pg. 13 Maintenance Instructions pg. 15 Security Features pg. 16 Trouble Shooting pg.

  • Page 4: Warnings & Recommendations

    WARNINGS AND RECOMMENDATIONS Anything in this installation guide that has been written in Italics is a WARNING. Failure to observe these instructions constitutes a MISUSE of this product and may result in serious physical injury or DEATH. NO UNAUTHORIZED REPAIR The Wall Vault™...

  • Page 5: Mounting Bolts

    WARNING: Never grab your frearm by the trigger when removing or placing into the Wall Vault™. Make sure your frearm’s safety mechanism is on. WARNING: Always follow the frearm safety rules set out by the frearm’s manufacturer. IMPORTANT NOTICE: - Vault must be in vertical position and installed on a vertical wall in order for door to drop open - Door must be open in order to install - Designed to install between 16”...

  • Page 6: Standard Features

    STANDARD FEATURES Drop down quick access door > 12 gauge stainless steel face > Plush fabric interior > Touchpad / Numeric Keypad > Biometric Finger Sensor with 6 user storage > (Model 20700 Only) Emergency access key lock with 2 keys >...
  • Page 7 Wall Vault ™...

  • Page 8: Installation Instructions

    INSTALLATION INSTRUCTIONS The Wall Vault™ is specifcally designed to be mounted into a standard residential wall with at least 2x4 construction and wall studs of at least sixteen (16) inches on center apart. It is recommended to use an industrial grade stud fnder to locate studs and ensure the wall void is free of other obstruc- tions (ie.
  • Page 9 Template 5 feet Wall Vault ™...

  • Page 10: Programming Model 20700

    PROGRAMMING INSTRUCTIONS (MODEL 20700) Biometric Sensor The fngerprint sensor maps your specifc fngerprint using the latest technology and computer algorithms. This technology is very accurate when a “good” fngerprint is captured, and is not easily fooled by coun- terfeits. In order to capture a “good” fngerprint, adequate pressure should be applied when frst enrolling a new fngerprint, i.e.
  • Page 11 Wall Vault | 10 ™...
  • Page 12 PROGRAMMING INSTRUCTIONS (MODEL 20700) Adding Additional Users Up to fve (5) additional users can be added to the system. To ensure safety please keep all codes secret. Press and release the ‘*’ button and wait for fve (5) seconds Press ‘2’ and hold for three (3) seconds. One (1) beep followed by three (3) beeps will indicate the system is in Enroll Mode.

  • Page 13: Programming Model 20710

    PROGRAMMING INSTRUCTIONS (Model 20710) Setting Main Pin Number The Wall Vault™ can store 2 access codes at a time. To program your access code, follow the instructions below. Open vault door. Default code is 1 2 3 4 followed by the ‘#’ key. Wait approximately ten (10) seconds until inner light turns off.

  • Page 14: Operating Instructions

    OPERATING INSTRUCTIONS Opening Door If pin number has not been changed, default code is 1 2 3 4 4 (Model 20700) or 1 2 3 4 (Model 20710). If pin number has already been programmed, default pin will not work until system is reset. Opening Door with Biometric Sensor (Model 20700) Please refer to the programing instructions on how to program fnger print(s).
  • Page 15 Wall Vault ™...

  • Page 16: Maintenance Instructions

    MAINTENANCE INSTRUCTIONS Charging Batteries When battery is low, an Alert beep will sound immediately following system startup. *Ensure power switch is turned on before charging system. 1. Plug AC Adapter into charger port (See Figure 24 for Model 20700 - See Figure 25 for Model 20710) 2.

  • Page 17: Security Features

    SECURITY FEATURES Function Possible Solution Tamper Lock Out When an incorrect code is attempted 5 consecutive times, the Wall Vault™ will go into Lock Out Mode for three (3) minutes. One (1) long beep followed by four (4) short beeps will indicate Lock Out Mode is activated.

  • Page 18: Troubleshooting

    TROUBLESHOOTING Problem Possible Solution Upon pulling it out of the 1. Ensure power switch is on. box, electronics do not 2. Charge battery for 48 hours. work. 3. If charging the battery does not activate electronic panel, call Customer Service. Power/touchpad are 1.

  • Page 19: Warranty & Registration

    These warranties are not assignable or transferable to any other person. In the event of failure ETL will, at its election, repair, replace or make appropriate adjustment where ETL inspection discloses any defects occurring in normal...
  • Page 20 © Copyright 2008. ETL ® and SecureLogic ® . All Rights Reserved. Patent # 7,178,370 B2...

This manual is also suitable for:

Securelogic wall vault 20710

Table of Contents