Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Artis M-173 FK
Summary of Contents for Artis M-173 FK
- Page 1 INSTALLATION MANUAL M-173 FK I M-183 FK...
-
Page 2: Table Of Contents
CONTENTS SPECIFICATIONS 1 . 1 DIMENSIONS 1 . 2 COMPONENTS 1 . 3 HEARTH & CLEARANCE REQUIREMENTS INSTALL INSTRUCTIONS 2 . 1 FREESTANDING 2 . 2 WALL MOUNTED 2 . 3 CHECKLIST WARRANTY FINAL WORDS... - Page 3 CONGRATULATIONS Thank you for choosing an Artis fireplace for your living space. Your fireplace is the result of careful design and quality manufactured from Spain. If properly installed, used and maintained, you will be sure to have an outstanding feature for years to come.
-
Page 4: Specifications
SPECIFICATIONS M-173 FK F R O N T T O P S I D E B A C K 97mm 81mm 390mm 67mm 492mm 668mm... - Page 5 SPECIFICATIONS M-183 FK FRONT 421 mm 169mm 150mm 842mm SIDE BACK 82mm 87mm 390mm 140mm 842mm 493mm...
-
Page 6: Components
COMPONENTS M-173 FK I M-183 FK FLUE SPIGOT SECONDARY AIR / GLASS WASH CONTROL DOOR HANDLE FAN SWITCH FAN OUTPUT WITH THERMOSTAT PRIMARY START UP AIR CONTROL... - Page 7 M-173 FK HEARTH & CLEARANCES STRAIGHT WALL APPLICATION COMBUSTIBLE WALL 275mm 140mm 950mm 1155mm 600mm 950mm The rear wall clearance for Straight Wall Applications, can be reduced to 100mm when installed with 12mm compressed board 1280mm wide x 555mm high, raised 200mm above the floor as a wall protector, and an appliance rear heat shield 675mm wide x 555mm high x 1.2mm galvanised steel with a 20mm air gap fitted directly behind the appliance level, with the top plate and an...
- Page 8 M-183 FK HEARTH & CLEARANCES STRAIGHT WALL APPLICATION COMBUSTIBLE WALL 250mm 1075mm 1085mm 600mm 1060mm The rear wall clearance for Straight Wall Applications, can be reduced to 100mm when installed with 12mm compressed board 1280mm wide x 555mm high, raised 200mm above the floor as a wall protector, and an appliance rear heat shield 840mm wide x 610mm high x 1.2mm galvanised steel with a 20mm air gap fitted directly behind the appliance level, with the top plate and an additional 180°...
- Page 9 INSTALLATION PRELIMINARY INFORMATION All units MUST be installed to Australian & New Zealand Standard AS/NZS 2918:2018. When in use some parts may become hot. A suitable fire guard is recommended where young, elderly or infirm are concerned. For the installation and use of this appliance, the technician and the user should strictly adhere to local and national regulations as well as AS/NZS 2918:2018.
- Page 10 Artis Fireplaces Pty Ltd & FM Calefaccion reserves the right to change these specifications without prior notice. The order of the steps indicated within this and any manuals provided by Artis Fireplaces Pty Ltd, are a recommendation only.
-
Page 11: Freestanding
INSTALLATION FREESTANDING HEARTH Lay a solid non-combustible floor protector / hearth, minimum 18mm thick. The hearth should be laid on an adequate ground supporting its weight. Ensure the base is level. See page 7 & 8 for required dimensions. POSITIONING Place the unit into a fixed position on top of the solid non- combustible floor protector / hearth. - Page 12 INSTALLATION FREESTANDING F L U E - I N S T A L L A T I O N Continue with triple skin flue into the roof cavity and extended above the roof line as per AS/NZ 2918:2018. A minimum of 4.6m total flue is required from the hearth / floor protection, to the cowl.
-
Page 13: Wall Mounted
INSTALLATION WALL MOUNTED HEARTH Lay a solid non-combustible floor protector / hearth, minimum 18mm thick. The hearth should be laid on an adequate ground supporting its weight. Ensure the base is level. See page 7 & 8 for required dimensions. STRUCTURAL PREPARATIONS Verify that the designated stud wall, chosen for fireplace installation, is indeed load-bearing and possesses the... - Page 14 INSTALLATION WALL MOUNTED FRONT DIAGRAM MASONRY WALL 600mm 950mm FLOOR PROTECTOR (18MM THICK)
- Page 15 INSTALLATION WALL MOUNTED SIDE DIAGRAM 100mm 600mm FLOOR PROTECTOR (18MM THICK)
- Page 16 INSTALLATION WALL MOUNTED STRUCTURE : DETAILED DRAWING 100MM BRICK OR NON COMBUSTIBLE STRUCTURE LOAD BEARING STUDS 6MM COUNTERSUNK DYNABOLT SCREWS MOUNTING BRACKET BRICK VENEER TIES / ANCHOR...
- Page 17 INSTALLATION WALL MOUNTED I N S T A L L A T I O N O F M O U N T I N G B R A C K E T S Determine the ideal placement for the fireplace on the masonry wall, ensuring level alignment with a spirit level With a masonry drill, create pilot holes for the dynabolts (6mm).
- Page 18 INSTALLATION WALL MOUNTED FLUE - PENETRATION Cut the required penetration hole in the desired position, in line with the flue spigot placement below. F L U E - I N S T A L L A T I O N Continue with triple skin flue into the roof cavity and extended above the roof line as per AS/NZ 2918:2018.
-
Page 19: Checklist
INSTALLATION CHECKLIST All installation steps have been read, understood and followed. Installation has been completed as per local regulations and industry standard AS/NZS 2918:2018 All components are present (refer to page 4) All moveable components (ie- door, flue damper control & air slides) are operational and move freely without obstruction No combustible materials left inside any section of unit, or within combustible clearance area (refer to page 5) -
Page 20: Warranty
WARRANTY INCLUSIONS & EXCLUSIONS ITEM DURATION Fireplace Firebox 5 year Repair or Replacement only on Firebox Ash Pan Door Handles 1 Year Replacement Fire Grates *Effective from date of purchase WARRANTY CLAIM REQUIREMENTS Proof Of Purchase Serial Number Photos / Videos Of Fault Compliance Certificate Installation Details (Date &... -
Page 21: Final Words
NOT to instruct independently. Whilst every effort is taken to avoid errors, Artis Fireplaces Pty Ltd and the manufacturer cannot accept responsibility for the accuracy of any statement, extract or information contained within this manual nor can any of its contributors who have submitted material for inclusion. - Page 22 artisfireplaces.com.au info@artisfireplaces.com.au 1300 851 304 05.24 V2...
Need help?
Do you have a question about the M-173 FK and is the answer not in the manual?
Questions and answers