Related Manuals for crosscontrol CCpilot X1200
Summary of Contents for crosscontrol CCpilot X1200
- Page 1 CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 CCpilot X1200 Technical manual...
-
Page 2: Table Of Contents
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 Contents 1. Introduction ..........................3 1.1. Product Models ........................3 1.2. Conventions and Definitions ....................3 1.3. Identification ........................3 1.4. Maintenance and Care ..................... 4 1.5. Cleaning ..........................4 1.6. Environment and Environmental Tolerance ..............4 2. -
Page 3: Introduction
1.3. Identification On the top side of the CCpilot X1200 device there is a label containing part number and serial number to uniquely identify your computer. Please take note of them as during service and other contact with the supplier it is important to be able to provide this information. -
Page 4: Maintenance And Care
1.6. Environment and Environmental Tolerance The CCpilot X1200 device has been designed to cope with tough environmental demands. Strict tests have been conducted on the unit in order to ensure that it fulfils the expectations of a rugged unit. -
Page 5: Device Overview
2024-06-17 2. Device Overview 2.1. Front Side On the front face of CCpilot X1200 there are buttons for switching the unit ON/OFF and adjusting the screens brightness level, a speaker, a status indicator and a light sensor. ON/OFF button Status Indicator... -
Page 6: Rear Side
Product revision: 1.0 Technical manual 2024-06-17 2.2. Rear Side The external connectors are located on the rear side of the CCpilot X1200, they are described in more detail in chapter 6 - Connectors. There are also mounting holes (M6) for fasteners in accordance with VESA 75. -
Page 7: Installation
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 3. Installation Install the device in such a way that is considered safe and does not expose any unnecessary stress to the unit. In this section, some recommendations are made regarding installation. -
Page 8: Grounding
Proper grounding minimizes electrical emissions which is why CrossControl recommend grounding CCpilot X1200 properly using as short and wide ground strap as possible. Attach the ground strap with a screw next to the ground symbol on the backside of the unit. Use a M5 screw with a maximum length of 10mm using the same procedure as described in section 3.3. -
Page 9: Cable Installation
2024-06-17 • When CCpilot X1200 or any other device is installed in a vehicle environment it is important that the installation is traffic safe. CrossControl does not recommend that CCpilot X1200 or its accessories are used actively by the driver or operator when a risk of injury to people, or damage to property, is present. -
Page 10: Basic Operations
• By using any of the operating systems shut-down procedures. CCpilot X1200 can also be turned off by pressing the ON/OFF button on the display for • four seconds and then releasing it. The time can be adjusted in the settings and it can also be disabled so that the unit cannot be shut down using the button to prevent turning the computer off accidentally. -
Page 11: Adjusting The Screen Brightness
CCAux API. See the software guide for details. 4.3. Adjusting the Screen Brightness Press the respective brightness button to gradually increase or decrease the CCpilot X1200 display brightness. The brightness can also be controlled from software (via CCSettingsConsole and/or CCAux API) which also allows for automatic adjustment of the brightness using the light sensor, see separate software guide for details. -
Page 12: Status Led Error Codes
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 4.6. Status LED error codes The status LED in the front is also used for indicating system related error codes by emitting a blue blinking pattern after shutdown of the device. The device may be started again when in this mode, by the key switch signal. -
Page 13: Interface Overview
5.2. Light Sensor A light sensor is located in the front of the CCpilot X1200. Using this sensor, ambient light levels can be measured and used by software to, for example automatically adjust the screen brightness. -
Page 14: Ethernet
5.6. Ethernet The CCpilot X1200 has two Ethernet interfaces, fully compatible with the 10BASE-T and 100BASE-TX standards and galvanically isolated (500 VAC or 707 VDC). Shielded cables shall be used to ensure reliable communication and EMC immunity. -
Page 15: Connectors
X6 USB1. As a part of the high environmental classification of CCpilot X1200, the unit is equipped with robust DIN M12 connectors. CrossControl can offer adapter cables which convert from DIN M12 to standard connectors. - Page 16 CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 X6, X7, X11, X12, X13 – USB 2.0 Connector Default Comments M12 x 1 signal Female, 5-pole VBUS Out Mini-B USB X10 - AUX Connector Default Comments DIN M12 x 1 signal...
-
Page 17: Specifications
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 7. Specifications The specifications may vary depending on your computer configuration. 7.1. Connections Interface / Feature Number of Connections 2 (4) USB 2.0 Ethernet AUX (Audio/RS232) (Bluetooth / Wi-Fi™ Antenna) 7.2. Technical Data... -
Page 18: Environmental Tolerance
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 Additional software CCAux API and ccsettingsconsole are available to access diagnostics and settings from software. Display 14.1” Type TFT-LCD, 16:10, anti-glare coated Resolution 1280 x 800 Colour Depth 16.2M Backlight LED, 1000 cd/m Bad pixels allowed Bright dots –... - Page 19 CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 The tests were performed with 24 V power level. Environmental tolerance may be affected by external factors like mounting and shielded cables etc. To comply with the Radio Equipment Directory (RED) BT/Wi-Fi antennas with maximum gain of 3dBi (2.4 GHz) and 5dBi (5GHz) shall be used.
-
Page 20: Weight And Dimensions
CCpilot X1200 Product revision: 1.0 Technical manual 2024-06-17 7.4. Weight and dimensions Description Comments Dimensions 350.4 x 277 x 57 mm (W x H x D) Weight 3.3 kg www.crosscontrol.com... -
Page 21: Technical Support
Possible error messages shown on the screen. • • Device log files (if possible). Information regarding possible external equipment which is connected to the device. • Additional sources of information are available on the CrossControl support site: • http://support.crosscontrol.com www.crosscontrol.com... -
Page 22: Trademarks And Terms Of Use
CrossControl. CrossControl respects the intellectual property of others, and we ask our users to do the same. Where software based on CrossControl software or products is distributed, the software may only be distributed in accordance with the terms and conditions provided by the reproduced licensors.
Need help?
Do you have a question about the CCpilot X1200 and is the answer not in the manual?
Questions and answers