Table of Contents
Related Manuals for honle uv-technik EVG UVT 40-150 W 0.8-1.5 A
Summary of Contents for honle uv-technik EVG UVT 40-150 W 0.8-1.5 A
- Page 1 uv-technik International • www.uv-technik.co.uk • Phone +44 (0)1582 805410 Operating Manual Electronic Power Supply EVG UVT 40-150 W 0.8-1.5 A EVG UVT 40-150 W 1.8-2.9 A EVG UVT 80-200 W 1.2-2.1 A EVG UVT 80-200 W 1.8-2.9 A Stand: 2/15/2023...
- Page 2 Imprint All rights reserved uv-technik international ©Copyright by Printed in Germany, 15 February 2023 No parts of this operating manual may be reproduced in any form without the prior written permission of the uv-technik international. If any part of this user’s manual is reproduced, stored in a retrieval system or transmitted in any form or by any means without obtaining the prior written permission of the uv-technik international, this will be considered as an infringement of the copyright and legal action will be taken.
-
Page 3: Table Of Contents
Summary description: Electronic power supplies EVG UVT 40-200 W Table of contents Warning notes and symbols in the operating instructions ............4 1 Device and function description ..................... 5 2 Safety instructions ......................... 6 General information ........................... 6 Appropriate use ............................6 Staff obligation ............................ -
Page 4: Warning Notes And Symbols In The Operating Instructions
Warning notes and symbols in the operating instructions These operating instructions describe the singled flamed electronic power supply of the EVG UVT series, its operation and its uses. The safety and warning notices explain the safe, proper handling of the device. You will find the symbols listed below next to all safety and warning instructions in these operating instructions where there is danger to life and limb. -
Page 5: Device And Function Description
1 Device and function description The EVG UVT is a microprocessor-based electronic power supply for UV low pressure lamps. It is available in the same size for wattages from 40-200 W. It allows to operate all UV low pressure lamps in a power range from 40 W up to 200 W with lamp currents from 0.8 A up to 2 A. -
Page 6: Safety Instructions
2 Safety instructions General information A sound knowledge of all basic safety regulations is essential to ensure safe and fault-free operation of the EVG UVT. This operating manual contains all important safety regulations to ensure safe operation of the equipment. This operating manual, and in particular the safety instructions, must be observed by all persons working with the equipment. -
Page 7: Hazards From Handling The Equipment
Hazards from handling the equipment The EVG UVT has been manufactured in accordance with the very latest state-of-the-art technology and the recognized rules of safety technology. The equipment may only be used under the following conditions: • it is used for the purpose for which it was constructed •... -
Page 8: Informal Safety Measures
Informal safety measures In addition to this user manual, the generally and locally applicable accident prevention and environmental protection regulations must be made available and observed. Danger due to electricity DANGER! – HAZARDOUS ELECTRICAL VOLTAGE! There is a danger causes by direct or indirect contact with electricity! The electrical components of the EVG UVT must be inspected regularly. -
Page 9: Transport, Storage, Delivery
3 Transport, storage, delivery The EVG UVT will be delivered in an appropriate packing. Any damage detected must be documented at once and reported immediately to your specialist dealer or directly to the uv-technik international. NOTE! Packing material must be disposed of in an environment friendly way or re-used if possible. We would recommend that the packing material be kept to protect the equipment if it needs to be shipped onward or otherwise transported. -
Page 10: Faults
6 Faults General information The following fault lists contain information on faults which may occur on the EVG UVT, possible causes and tips on how to remedy the fault. If a fault occurs on your equipment and cannot be remedied by following these instructions, contact the customer service department of the uv- technik international. -
Page 11: Technical Data
7 Technical data Product description main features intended use ballast with preheating for all applications with Amalgam UV lamps cut off of preheating current in operation for water and air applications lamps and current adjustable in 10 steps for applications with many switches ballast with dimming input for installation in cabinets with limiter of inrush current... -
Page 12: Monitoring Circuitry
Monitoring circuitry mains voltage monitoring cut off in case of persisting under- or overvoltage temperature monitoring cut off in case of persisting over temperature lamp presence check prevention of ignition if lamp is not connected or filament check if a wrong filament is indentified short circuit of lamp wires immediate cut off lamp failure... -
Page 13: Technical Documentation
8 Technical documentation Terminal diagram Dimensional drawing subject to change without notice VGN EVG UVT 40-200W RS485 MA v1.0.3 E page 13 of 17... -
Page 14: Installation Instructions
9 Installation instructions Point of installation The EVG UVT must be installed and operated only in a dry, chemically and bioligically inactive environment. Installation in vibrating parts of the system is not allowed. Hints regarding IP protection have to be observed. - Page 15 Grounding A clean earth potential and a proper grounding with an adequate cable cross section are the preconditions for compliance with the EMC standards. Only if this is guaranteed, high frequecy disturbances can be derived an thus prevented. Therefore, always connect all grounding terminals. Ground the mounting base plate.
- Page 16 temperature of ballasts for most of the time below the maximum allowable temperature (approx. 10K less). Hence, you will achieve a longer lifetime and better operating safety. Switching When switching the EVG UVT on an inrush current pulse of very short duration arises by the up-charge of the integral storage capacitor for the internal power supply.
- Page 17 Hence the available dimming range is slightly smaller based on the lamp power. To avoid a cutoff, please note that the allowed minimum power of the EVG UVT must not undercut in case of dimming. Please check self dependent if you can use the full dimming range. If necessary, the operating temperature of the lamp as well as its possible dimming range can be influenced by a diameter adaption of the lamp protection tube.
Need help?
Do you have a question about the uv-technik EVG UVT 40-150 W 0.8-1.5 A and is the answer not in the manual?
Questions and answers