Advertisement
Quick Links
Operating Instructions & Parts Manual
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself
and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions
for future reference.
Westward Auxiliary Stand
Description
Westward auxiliary stand is designed as a means of partial support for, and the
positioning of, vehicle components during their installation/removal, but not for use in
stabilizing or supporting vehicles. Heavy gauge steel construction and compliance with
the latest ANSI/PALD standards ensure safety, strength and stability.
Specifications
Model
Capacity
1VW33
3/4 Ton
(1500 Lbs)
Figure 1 - Auxiliary Stand Components
General Safety Information
Familiarize yourself
throughly with
product, read and understand owner's
manual before use.
D
not exceed rated capacity.
o
Use only on hard level surface.
Adequately support the vehicle before
starting repairs.
Do not use to support or stabilize vehicle.
Center load on saddle.
No alterations shall be made to this
product.
SHI 023
Printed in China
03/10
®
Base
Min.
Diameter
Height
12"
53-
/
3
saddle
main post
Failure to heed these markings may result
in severe, even fatal injury and/or property
damage.
Assembly
Use Figure 2 as reference.
1. Insert solenoid (#11) into main post
(#5).
2. Attach bearing (#10), adjusting handle
(#8) & saddle (#6) on solenoid.
3. Secure saddle using lock pin (#7,
punch in), and make sure it is stable.
Max.
Height
"
79-
/
"
1
8
8
saddle
adjusting handle
foot pedal
base support
4. Attach main post into base support (#1)
secure by pin (#4), washer (#12) &
"C"clip (#13).
5. Attach foot pedal (#14), secure by pin
(#15), washer (#2) & "C" clip (#3).
6. Attach grease fitting nipple (#9) onto
adjusting handle.
Operation
Note: Grease prior to first use
RAISING
Turn adjusting handle clockwise until
saddle contacts load. Continue turning
handle to raise load to required height.
Use foot pedal for fine adjustment
LOWERING
Turn adjusting handle counter-clockwise.
Maintenance
Periodically inspect the stand. Ensure all
parts move freely. Apply grease to fitting
as needed. If rust appears, sand affected
area and cover with suitable utility paint.
Owner / User Responsibility
The owner and/or user must have an
understanding of these operating
instructions and warnings before using
this auxiliary stand. Personnel involved
in the use and operation of equipment
shall be careful, competent, trained, and
qualified in the safe operation of the
equipment and its proper use when
servicing motor vehicles and their
components. Warning information should
be emphasized and understood. Owner
and/or user must study and maintain for
future reference the manufacturer's
instructions. Owner and/or user is
responsible for keeping all warning labels
and instruction manuals legible and
intact.
1VW33
Advertisement
Related Manuals for Westward 1VW33
Summary of Contents for Westward 1VW33
- Page 1 4. Attach main post into base support (#1) secure by pin (#4), washer (#12) & Westward auxiliary stand is designed as a means of partial support for, and the “C”clip (#13). positioning of, vehicle components during their installation/removal, but not for use in stabilizing or supporting vehicles.
- Page 2 1VW33 Westward Operating Instructions and Parts Manual Westward Auxiliary Stand ® Owner / User Responsibility (Continued) Figure 2 - Assembly Parts Illustration...
- Page 3 1VW33 Westward Operating Instructions and Parts Manual For Repair Parts, call 1-800-323-0620 24 hours a day - 365 days a year Please provide following information: -Model number -Serial number (if any) -Part description and number as shown in parts list...
- Page 4 Stand, Model covered in this manual, is warranted by Westward to the original user against defects in workmanship or materials under normal use for one year after date of purchase. Any part which is determined to be defective in material or workmanship and returned to an authorized service location, as Westward designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced at Westward's option.
Need help?
Do you have a question about the 1VW33 and is the answer not in the manual?
Questions and answers
the c clip falls out how to fix it
To fix the C-clip falling out on the Westward part number 1VW33, follow these steps:
1. Inspect the C-clip and Groove – Ensure the C-clip (#13 or #3) is not damaged or worn. Also, check if the groove where it sits is clean and undamaged.
2. Reinstall Securely – If the C-clip is intact, press it firmly into the groove using pliers or a C-clip installation tool, ensuring it snaps into place securely.
3. Use a Retainer or Adhesive – If the C-clip continues to fall out, consider using a small amount of thread locker or retaining compound to help secure it.
4. Replace if Necessary – If the C-clip is bent or loose, replace it with a new one of the same size to ensure a secure fit.
5. Check for Excess Movement – Verify that the connected parts are not excessively worn, which could cause the C-clip to loosen.
These steps should help prevent the C-clip from falling out during operation.
This answer is automatically generated