Table of Contents
Advertisement
Quick Links
OPERATION AND MAINTENANCE BOOK
FLAT - SUPER FLAT
Document Code: 0150MANFMEN.000
PREAMBLE
The present handbook must be considered as integral part of the equipment, and it must always be available
to the persons operating with the unit; this manual must always stay with the equipment, also in case the
unit is transferred to another owner.
The operators must carefully read this handbook and follow all instructions herein contained, because
VINSERVICE MICRO MATIC will not be liable for any damages occurred to persons and/or things, or
suffered by the equipment itself, whenever any conditions here in described are not respected.
Customers have the obligation to respect the industrial trade secret, according to which the following
literature and its enclosures could not be altered, edited, or sold to third parties, without the explicit
authorization of VINSERVICE MICRO MATIC.
VINSERVICE MICRO MATIC S.R.L. Via G. Falcone, 26/34 - 24050 ZANICA (BG) Italy
Phone: +39.035.672361 Fax: +39.035.672699
www.vinservice.it | e-mail: vinservice@micro-matic.com
1
Advertisement
Table of Contents
Related Manuals for Vinservice FLAT
Summary of Contents for Vinservice FLAT
- Page 1 The operators must carefully read this handbook and follow all instructions herein contained, because VINSERVICE MICRO MATIC will not be liable for any damages occurred to persons and/or things, or suffered by the equipment itself, whenever any conditions here in described are not respected.
- Page 2 SYMBOLS AND SIGNS Within this document, as well as directly on the casing or inside the appliance, graphics symbols are use to draw the operator’s attention instantly. According to the situations, such symbols may indicate the obliga- tion to operate in the manner specified, any possible occurrence of dangerous situations or the prohibition to carry out the actions specified.
-
Page 3: Table Of Contents
INDICE PREAMBLE........................ALPHABETIC INDEX OF REFERENCES................SUPPLY CONDITIONS....................... AIM OF THE DOCUMENT....................PERSONNEL QUALITIES....................REFERENCED STANDARDS....................FIELD OF EMPLOYMENT....................MACHINE DESCRIPTION....................TECHNICAL SPECIFICATION.................... THERMOSTATS: DIGITAL, MECHANICAL, ELECTRONIC............ SYMBOLS AND SIGNS...................... ACCIDENT PREVENTION AND RESIDUAL RISKS............... LIFTING AND TRANSPORT....................INSTALLATION........................ TROUBLESHOOTING......................MAINTENANCE........................ - Page 4 Alphabetic index of references Symbols (B), recirculation pump........................9, 10, 16, 17 (C), distributor..............................9, 16 (E), tank............................8, 9, 15, 17, 18 (F), agitator..........................9, 10, 15, 16, 17 (G), probe..............................9, 16, 17 (H), compressor............................9, 16, 17 (IG), master switch ........................10, 15, 16, 17 (L), condenser............................8, 9, 18 (M), fan..............................9, 16, 17 (N), capillary tube..............................9 (O), evaporator...............................9, 16 (Q), overflow............................10, 15, 18 (R), openable panel..........................10, 12, 15 (TD), digital thermostat............................16 (TR), transformer OPTIONAL.........................9, 16...
-
Page 5: Supply Conditions
VINSERVICE MICRO MATIC will not be held liable for any failure to comply with the standards governing correct installation. VINSERVICE MICRO MATIC will not be held liable for any loss in production unless expressly shown in the purchase order. VINSERVICE MICRO MATIC will not be held liable for any defects or malfunction arising from; improper use of the equipment, alterations due to the transportation or peculiar environmental conditions, lack off or improper maintenance, manhandling or improper service;... -
Page 6: Referenced Standards
N.B. VINSERVICE MICRO MATIC will not be held liable for unsuitable and/or unhygienic conditions in the workplace. • VINSERVICE MICRO MATIC will not be held liable for damages of any type arising from non-compliant or unwise usage. • Distribution of beverages without prior cleaning and sanitizing equipment is strictly prohibited. -
Page 7: Machine Description
MACHINE DESCRIPTION • The cooler VINSERVICE MICRO MATIC belonging to the glycol line allows the temperature of the liquid recirculating in the system to lower. As a result, the temperature of the dispensing body (C) will also lower and will cause either a condensation or ice effect on the body surface. - Page 8 OPTIONAL: DIGITAL THERMOSTAT: INSTRUCTIONS FRONT PANEL DESCRIPTION KEYS DESCRIPTION and for decreasing the values to be set. and for increasing the value to be set. Also used for 4.Key : Used for visualizing the read temperatures. LED INDICATORS 9.Led AL: Indicats the alarm status. Led on = (ON), 5.Led OUT: Indicates the compressor or temperature device out- 10.Led SET: Indicates access to programming mode and Led blinking = (INHIBITED)
- Page 9 THERMOSTAT PROGRAMABLE PARAMETERS SWITCH POWER SUPPLY OFF & ON AFTER PARAMETER MODIFICATIONS. MINI MEDIUM PARAMETER DESCRIPTION MINI MEDIUM TWIN SUPREME FLAT PARAMETER DESCRIPTION TWIN TWIN COLDER TWIN TWIN TWIN SUPREME FLAT CUBE GLYCOL...
-
Page 10: Accident Prevention And Residual Risks
Carefully keep the technical documentation accompanying the equipment. • VINSERVICE MICRO MATIC will not be held liable if installation instructions are not followed. • Do not use the equipment if any operating fault occurs. -
Page 11: Lifting And Transport
Proper illumination of equipment installation location is advised to guarantee that all necessary operations are carried out in safe conditions. Although VINSERVICE MICRO MATIC has removed sharp edges where possible, however, the use of personal protective devices e.g. leather gloves is recommended when handling: sheet metal, condenser fins (H), self-threading screws, etc. -
Page 12: Installation
INSTALLATION The chiller operation is completely automatic and does not require any particular intervention of the operator. • First of all make sure that no leaks are present in the system and carry out a periodical control, as the chiller can be left always running. •... -
Page 13: Troubleshooting
N.B. Control and maintenance operations must be carried out when the machine is stationary and with the power supply disconnected, pulling out the plug. Any operation excluded from those started below must be carried out by specialized and authorized personnel TROUBLESHOOTING CHECKS AND POSSIBLE ANOMALY DETECTED... -
Page 14: Maintenance
, if available, in a dry place. Do not stack more machi- ne components without the original packaging. • VINSERVICE MICRO MATIC accepts no responsibility for the disposal of the packaging or parts of the machine or products used to run the machine: coolant gas, compressor or under-pressure containers, condensers, etc. -
Page 15: Technical Drawings
TECHNICAL DRAWING SUPER FLAT 598,00 398,00... - Page 16 TECHNICAL DRAWING - FLAT 407,00 407,00 430,00 421,00...
- Page 17 NOTES...
- Page 18 NOTES...
- Page 19 NOTES...
-
Page 20: Declaration Of Conformity
“MACHINE” 2006/42/CE “LOW TENSION” 2006/95/CE “EMC” 2004/108/CE VINSERVICE MICRO MATIC S. R. L. - VIA G. FALCONE 26/34. 24050 ZANICA (BG) Declares under its own responsability that: FLAT - SUPER FLAT Have been designed and built in compliace with the safety requirements requested by the “CE”...
Need help?
Do you have a question about the FLAT and is the answer not in the manual?
Questions and answers