Page 2
World-leading provider of embedded/IoT products and solutions Revision History: Version Description Date V1.0 First release Oct. 23, 2022 Supplemented the pinout description of the V1.1 Jul. 14, 2023 JAE connector V1.2 Added the use of the serial port Nov. 14, 2023 Oplayer3399 | User Manual www.vantrontech.com...
Under no circumstances shall any part of this user manual be copied, reproduced, translated, or sold. This manual is not intended to be altered or used for other purposes unless otherwise permitted in writing by Vantron. Vantron reserves the right of all publicly released copies of this manual.
Page 5
Please refer to the Appendix for Regulatory Compliance Statement. Symbology This manual uses the following signs to prompt users to pay special attention to relevant information. Caution for latent damage to system or harm to personnel Attention to important information or regulations Oplayer3399 | User Manual www.vantrontech.com...
Page 6
The use or placement of the operation tools shall comply with the code of practice of • such tools to avoid short circuit of the Product. • Cut off the power before inspection of the Product to avoid human injury or product damage. Oplayer3399 | User Manual www.vantrontech.com...
Page 7
• Clean with a damp cloth Do not try to clean exposed electronic components unless with a dust collector • Power off and contact Vantron technical support engineer in case of the following faults: The Product is damaged • •...
Vantron Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions CHAPTER 1 INTRODUCTION Oplayer3399 | User Manual www.vantrontech.com...
USB 2.0 & 3.0 ports, RS232 and Ethernet jack, allowing for flexible connectivity with different peripherals. Oplayer3399 can be easily connected to an OPS compliant display via the JAE TX24/25 plug connector which offers DisplayPort, HDMI, USB 2.0, USB 3.0, audio (Line-out), power input and UART signals.
Input Output Input/output Power or ground Analog Open collector output CMOS 3.3 V CMOS LVCMOS Low Voltage CMOS LVTTL Low Voltage TTL 3.3V 3.3V signal level 5V signal level Universal Serial Bus CK/CLK Clock (line) Oplayer3399 | User Manual www.vantrontech.com...
& power cord 1 x Wi-Fi antenna 2 x 4G LTE antenna 1 x Qualified certificate Actual accessories might vary slightly from the list above as the customer order might be different from the standard configuration options. Oplayer3399 | User Manual www.vantrontech.com...
SIM slot indicator antenna Wi-Fi 4G primary antenna antenna HDMI USB 2.0 A ON/OFF USB 3.0 A Line out Micro USB 3.0 A Power indicator Recovery button 1.6.2 Back view JAE TX24/25 DC jack connector Oplayer3399 | User Manual www.vantrontech.com...
200mm x 120mm x 30mm (With mounting frame) 1.9 Power Supply Oplayer3399 is designed to work with 12V ~ 24V DC power input via the power jack on the back of the device or powered by 12V ~ 19V DC from the docking display via the pluggable connector.
Vantron Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions CHAPTER 2 GETTING STARTED Oplayer3399 | User Manual www.vantrontech.com...
World-leading provider of embedded/IoT products and solutions 2.1 Device Installation Typically, Oplayer3399 is used with an OPS compliant display to offer a digital signage solution for users with 4K UHD output. The following steps use Vantron TMC550 55-inch touchscreen monitor to illustrate how to install Oplayer3399 to an OPS compliant display.
World-leading provider of embedded/IoT products and solutions 2.2 Using the Device Oplayer3399 is also intended for independent use as a common industrial computer. To access the GUI of the device, follow the steps below to connect it to a mouse, keyboard and monitor.
Vantron Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions CHAPTER 3 HARWARE DESCRIPTION Oplayer3399 | User Manual www.vantrontech.com...
Specification: 2 x 40, 1.27mm, 1A, Male, 9mm H, Right Angle, WDT, THR, RoHS Pinout description: Signal Description I/O Type DDP_3N DisplayPort DDP_3P DisplayPort Ground DDP_2N DisplayPort DDP_2P DisplayPort Ground DDP_1N DisplayPort DDP_1P DisplayPort Ground DDP_0N DisplayPort DDP_0P DisplayPort Ground Oplayer3399 | User Manual www.vantrontech.com...
Page 20
Ground +12V~+19V Power +12V~+19V Power +12V~+19V Power +12V~+19V Power +12V~+19V Power +12V~+19V Power +12V~+19V Power +12V~+19V Power RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved RSVD Reserved Oplayer3399 | User Manual www.vantrontech.com...
Page 21
USB_PN2 USB_PP2 Ground USB_PN1 USB_PP1 Ground USB_PN0 USB_PP0 Ground AZ_LINEOUT_L Audio-Lch AZ_LINEOUT_R Audio-Rch Consumer Electronics Control PB_DET Pluggable Board Detect PS_ON# Pluggable Signal ON PWR_STATUS Power Good OUT (OC) Ground Ground Ground Ground Ground Ground Oplayer3399 | User Manual www.vantrontech.com...
World-leading provider of embedded/IoT products and solutions Power jack Oplayer3399 is designed to work with 12V ~ 24V DC power input via the power jack on the back of the device or powered by 12V~19V DC from the docking display via the pluggable connector.
HDMI HOT PLUG DETECTION Serial port Oplayer3399 offers a serial port that operates in RS232 mode by default and can be easily switched to RS485 mode with a baud rate of 9600. Please refer to 4.5 for the commands to switch the serial modes.
World-leading provider of embedded/IoT products and solutions USB ports Oplayer3399 implements three USB 2.0 Type-A ports and a USB 3.0 Type-A port ideally for connecting USB peripherals such as a keyboard, mouse, scanner, etc. There is also a Micro USB port for connecting compact and mobile devices. It also supports USB 2.0 OTG for debugging the device.
Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions 3.10 Line out Oplayer3399 provides a line out jack on the front panel for connecting an earphone or amplifier. 3.11 LED indicators There are two LED indicators on the front panel with functions separately described as follows.
Vantron Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions CHAPTER 4 SOFTWARE SETUP Oplayer3399 | User Manual www.vantrontech.com...
World-leading provider of embedded/IoT products and solutions Enable Developer Options To enable Developer options of Oplayer3399, follow the steps below: 1. Connect the device to a mouse, a keyboard, and a monitor for easier operations; 2. After the system has booted, swipe up to access the application drawer;...
Page 28
5. Paste the folder path of the adb tool, and click OK one by one to confirm and exit the dialog; 6. Press “Win + R” and input cmd in the dialogue box; 7. Input adb version in the command prompt to check if the ADB tool is installed. Oplayer3399 | User Manual www.vantrontech.com...
1. Follow the steps in 4.2 to finish ADB setup on the host computer; 2. Turn on Oplayer3399 and make sure the LED indicator on the ON/OFF button is blue; 3. Connect Oplayer3399 and the host computer via a Micro USB cable;...
7. Unzip the folder and double click the driver for the upgrade tool RKDevTool.exe to open the upgrade window; 8. Connect Oplayer3399 to the Windows host computer using a Micro USB cable; 9. Press “Win + R” and input cmd in the dialog box to open the command prompt;...
Page 31
15. Click the Upgrade button and the device will start to download the image and upgrade the firmware automatically; 16. When the upgrade finishes, the device will reboot automatically. Oplayer3399 | User Manual www.vantrontech.com...
World-leading provider of embedded/IoT products and solutions Serial Port Oplayer3399 offers a serial port that operates in RS232 mode by default and can be easily switched to RS485 mode with a baud rate of 9600. Please confirm if a 4G module is installed on the device before using the serial port. For Oplayer3399 with a 4G module, the serial port is mapped as ttyUSB4 in the system.
# echo 1 > value To transmit and receive data in RS485 mode: # cd # cd dev/ # echo “vantron” > ttyUSB0 # cat ttyUSB0 You can restart the device or execute the following commands to switch the serial mode back to RS232.
Vantron Embedded in your success, Embedded in your better life World-leading provider of embedded/IoT products and solutions CHAPTER 5 DISPOSAL AND WARRANTY Oplayer3399 | User Manual www.vantrontech.com...
& electronic waste recycling/disposal center. Proper disposal of this sort of waste helps avoid harm and adverse effect upon surroundings and people’s health. Please contact local organizations or recycling/disposal center for more recycling/disposal methods of related products. Oplayer3399 | User Manual www.vantrontech.com...
CUSTOMER’s location and no Product so inspected shall be returned to VANTRON unless the cause for the rejection or defect is determined to be the responsibility of VANTRON. VANTRON shall in turn provide the CUSTOMER turnaround shipment on defective Product within fourteen (14) working days upon its receipt at VANTRON.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate this equipment. Oplayer3399 | User Manual www.vantrontech.com...
Need help?
Do you have a question about the Oplayer3399 and is the answer not in the manual?
Questions and answers