Page 2
Travel in comfort and convenience - Welcome to the group of caravan owners! your home on four wheels Congratulations on the purchase of your new LMC caravan! You have purchased a high-quality, reliable and elegant vehicle that offers special advantages and extraordinary comfort.
Operating manual and inspection booklet Introduction ......................7 Technical documentation ................8 Explanation of symbols used ............... 9 Vehicle registration ..................11 Keys ......................11 Safety ........................12 Intended use ....................
Page 4
Operating manual and inspection booklet Overview ......................49 Caravan body .................... 50 5.1.1 Keys ....................50 5.1.2 Entrance door ................50 5.1.3 Door and hatch locks ..............54 5.1.4 Window ..................57 ...
Page 5
Operating manual and inspection booklet Camping ......................107 Setting up the caravan ................107 6.1.1 Establishing the power connection ..........107 6.1.2 Filling the fresh water tank ............107 6.1.3 Draining fresh water ..............109 ...
Page 6
Operating manual and inspection booklet Maintenance and inspection ................173 Maintenance schedule ................174 Inspection schedule ................. 175 Wheels and tyres ..................176 8.3.1 Changing wheels ................. 180 8.3.2 Tyre pressure table ..............184 ...
Operating manual and inspection booklet Introduction gthhygdydgdfg 1 Introduction Before the first trip Your dealer will provide extensive instruction in all important functions when your vehicle is transferred to you so that you can properly operate and use your vehicle at any time. In addition, this operating manual provides important information for using the vehicle and equipment.
Operating manual and inspection booklet Introduction 1.1 Technical documentation The following vehicle documents are in the document case: Manufacturer documentation Operating manual with inspection booklet for leakage warranty Supplemental documents Documents from the chassis manufacturer Device operating manual for cooker ...
Operating manual and inspection booklet Introduction 1.2 Explanation of symbols used Safety and warning signs Important instructions are especially marked by symbols and signal term. Comply exactly with the specified instructions to prevent personal injury, material damage and environmental damage. DANGER Danger to life and/or severe damage to health This symbol combined with the "DANGER"...
Page 10
Operating manual and inspection booklet Introduction NOTICE Tips and recommendations This symbol combined with the "NOTE" signal term identifies useful tips and recommendations for the efficient handling of the vehicle and its equipment. NOTICE Environmental protection This symbol combined with the "NOTE" signal term identifies important information regarding an environmentally conscious behaviour.
Operating manual and inspection booklet Introduction 1.3 Vehicle registration Obligation to register Pursuant to applicable national regulations, your vehicle must be registered with the relevant authority. Registration is issued by the vehicle licensing organization of your local government. Required documents For registration you require: Registration certificate part I (vehicle registration certificate) ...
Operating manual and inspection booklet Safety 2 Safety This section lists all the important safety aspects for optimal protection of persons in the vehicle, and for safe and trouble-free use of the furnishings. Moreover, the following sections include additional safety instructions for avoiding imminent dangers when using devices and equipment.
Operating manual and inspection booklet Safety 2.2 Responsibility of the vehicle owner The vehicle has been designed and built in accordance with state of the art and in accordance with recognised safety-related rules. Nevertheless if the instructions in the operating manual are not followed serious personal injury, significant material damage to or on the vehicle or environmental damage can occur.
Operating manual and inspection booklet Safety 2.3 General requirements For your own safety and the safety of your passengers always comply with the following instructions: People must travel in the towing vehicle, and never in the caravan body. Travel with the caravan only when it is technically sound and fully roadworthy.
Operating manual and inspection booklet Safety 2.4 Fire safety Avoid fire and fire propagation! Always keep the smoke alarm, located in the ceiling of the caravan body, in functional condition. Prior to using the vehicle for the first time, remove the protective foil from the block battery in the smoke alarm and connect the block battery to activate the smoke alarm.
Operating manual and inspection booklet Safety 2.5 Traffic safety Driving in public traffic always demands special caution and attentiveness. Always comply with locally applicable traffic regulations, the operating guidelines for the vehicle and the following instructions! 2.5.1 Vehicle Dimensions and weight Caravan and towing vehicle together comprise a rig with large dimensions and heavy weight.
Page 17
Operating manual and inspection booklet Safety Rig operation Risk of injury for people in the coupling area when the caravan is coupled. Always ensure that: The towing vehicle has a functionally safe trailer pulling device and electrical connector coupling. The caravan is in an operationally safe condition, has a valid ...
Page 18
Operating manual and inspection booklet Safety Wheels and tyres Worn tyres and incorrect tyre pressures adversely affect the driving and braking behaviour of the vehicle and can cause accidents. Always ensure that: Rims and tyres must be approved for the vehicle ( motor vehicle registration certificate part I).
Page 19
Operating manual and inspection booklet Safety Vehicle equipment Mandatory equipment 2 Wheel chocks Depending on the local regulations in the country of initial registration, additional equipment may be pre-installed in the vehicle. For example, vehicles for initial registration in Germany contain: ...
Operating manual and inspection booklet Safety 2.5.2 Load Excessive load and improper arrangement of the load adversely affect the driving characteristics and braking behaviour of the vehicle and can cause accidents. Always ensure that you: Do not exceed the gross vehicle weight rating ( motor vehicle registration certificate part I).
Operating manual and inspection booklet Safety 2.5.3 Driving Before the trip Unsecured load, a vehicle in a condition that is not ready to drive and/or technical defects can cause accidents with severe or fatal injuries. Before starting your trip, always perform the following tasks: ...
Page 22
Operating manual and inspection booklet Safety On the road Failure to comply with local traffic regulations can cause accidents with serious or fatal injuries. When driving the towing vehicle: Always comply with local traffic regulations. Always adjust your driving to current road and traffic conditions and the total weight and dimensions of your rig.
Operating manual and inspection booklet Safety 2.6 Operational reliability 2.6.1 Gas supply General The gas supply system was installed, inspected and accepted according to DIN EN 1949 and a pressure and tightness was completed according to the German Association for Gas and Water DVGW worksheet G 607.
Page 24
Operating manual and inspection booklet Safety Using the gas devices Use only tested and intact gas devices and gas bottles (11 kg or 5 kg bottles). Open the quick-action valve of a gas device only if the device is to be operated.
Page 25
Operating manual and inspection booklet Safety Driving and parking Prior to starting the trip, close the glass bottle valve and the quick-action valves of the gas devices. Do not operate any gas devices when refuelling, on ferries, in garages or parking facilities.
Operating manual and inspection booklet Safety 2.6.2 Electrical system General The vehicle is equipped with a power supply system for: Combined operation, that is, the 230 V input via CEE-outlet and use of 230 V consumers and 12 V operators, thanks to the 12 V converted installed in the caravan.
Page 27
Operating manual and inspection booklet Safety If a stand-alone package (optional) is installed, the towing vehicle does not provide 12 V supply for the interior. In this case, the supply battery in the caravan ensures the entire supply. The entire 12 V network in the interior is available when the 12 V main switch is actuated.
Page 28
Operating manual and inspection booklet Safety Electrical system and devices Connect only tested and intact devices. Any device exhibiting defects, faults or external damages must be immediately disconnected from the vehicle system. Periodic testing by an electrician. ...
Operating manual and inspection booklet Safety 2.6.3 Sanitary system The caravan is factory-equipped with a fresh water tank and a toilet. A 25 l waste water tank on rollers (optional) is available as option. WARNING Health hazards due to chemicals! Harmful chemical cleaning agents are required for toilet hygiene.
Page 30
Operating manual and inspection booklet Safety Hygiene WARNING Health hazard due to germs and bacteria in the drinking water! Contaminated drinking water can cause serious infections. • Prior to the first use, disinfect the fresh water system of the vehicle, and thoroughly flush with drinking water.
Operating manual and inspection booklet Safety Reisemobilistinnen 2.7 Environmental protection Reisemobilistinnen Cleanliness Real camping enthusiasts always leave their stopover clean and tidy. Always behave in such a manner that you will be welcomed back! Many towns and communities offer designated and well- equipped compounds with all necessary supply and disposal facilities for caravans.
Operating manual and inspection booklet Technical data 3 Technical data General This section contains a selection of important technical data. A complete overview of all technical specifications is provided in the price list and the enclosed operating manuals of the devices installed.
It must always be in legible condition. The nameplate contains the following information (from top to bottom): Manufacturer ETG No. LMC Chassis No. Permissible total weight Permissible axle load, axle 1 Fig. 1: Nameplate ...
Operating manual and inspection booklet Driving 4 Driving Fundamentals When driving your caravan, always comply with the regional traffic regulations and laws. Carefully plan your route in advance. Drive carefully and in an environmentally responsible manner. Bear in mind that your rig has dimensions and weight that are significantly greater than those of a car.
Operating manual and inspection booklet Driving Personal items Weight of all items carried in the caravan not contained in the aforementioned list, such as foodstuff, crockery, radio, TV, clothing, bedding, toys, books, toiletry articles, bicycles, boats, surfboard, sport equipment. These objects must be taken into account in any event, regardless of where they are stored.
Operating manual and inspection booklet Driving 4.1.3 Loading and stowing luggage Prior to loading the vehicle, check the location and arrangement of storage spaces in the vehicle ( section "Storage spaces"). Follow the instructions in the "Safety" section! Distribute the luggage properly. 1.
Operating manual and inspection booklet Driving 4.2 Checking the vehicle WARNING Danger of accident and injury due to vehicle defects! Defects on and in the vehicle can cause accidents with severe to fatal injuries as the consequence. • Prior to every start, check the vehicle and the load for condition and driving safety.
Operating manual and inspection booklet Driving 4.3 Coupling the caravan and the towing vehicle 4.3.1 Prerequisites for coupling WARNING Safety Risk of injury when moving or standing between caravan and towing vehicle! If the towing vehicle is moved backward, persons positioned between the vehicles can be caught between the vehicles and severely injured.
Page 39
Operating manual and inspection booklet Driving The design of the coupling system depends on the caravan model and the selected equipment. Additional information on handling the caravan coupling is supplied in the accompanying operating manual provided by the manufacturer. Before using the caravan coupling for the first time, note the ...
Operating manual and inspection booklet Driving 4.3.2 12 V power supply in towing operation 13-pole plug The 12 V-power supply of the caravan in coupled condition is ensured only when the towing vehicle and the caravan aire connected via a 13-pole plug. Contact Power circuit Wire Ø...
Operating manual and inspection booklet Driving 4.3.3 Coupling with "AL-KO" safety coupling WARNING Danger of accident and injury if the caravan becomes detached! If improperly coupled, the caravan can become detached from the towing vehicle and cause serious Fig. 3: Basic position accidents with fatal consequences.
Page 42
Operating manual and inspection booklet Driving Insert the electrical connector plug of the caravan into the towing outlet on the towing vehicle. Check the lights (rear light, brake lights, blinkers, reverse light, clearance lights) on the caravan. 10. Release the parking brake before starting the trip. 11.
Operating manual and inspection booklet Driving 4.3.4 Uncoupling with "AL-KO" safety coupling NOTE When uncoupling the caravan, the overrun device must be relaxed and the bellows must be extended. Engage the parking brake of the caravan. Detach the contact breaking cable and remove from the towing vehicle.
Operating manual and inspection booklet Driving 4.4 Travelling and parking Travelling WARNING Risk of injury and accident due to incorrect behaviour! The rig comprised of towing vehicle and caravan has large dimensions and a great weight. Incorrect behaviour can result in accidents with serious or fatal injury as the consequences.
Page 45
Operating manual and inspection booklet Driving Parking WARNING Risk of injury due to an unsecured vehicle! Unsecured vehicles can roll away and cause serious injury or material damage. • Never stop or park the caravan on steep slopes, embankments or gradients. •...
Operating manual and inspection booklet Driving 4.5 Parking the caravan at the destination 4.5.1 Parking the caravan Selecting a parking place For optimal and trouble-free use of all technical vehicle equipment, select the parking place in accordance with the following criteria: ...
Operating manual and inspection booklet Driving 4.5.2 Extending and retracting the support elements WARNING Crushing hazard when extending or retracting the support elements! Extending and retracting support elements can cause feet, hands, or other body parts to be crushed and injured.
Page 48
Operating manual and inspection booklet Driving Extending the prop Place the socket wrench from the gas bottle box on the hexagonal bolt (1) at the front right caravan corner. Turn the socket wrench clockwise until the support element rests firmly on the ground. Extend the support element on the left front side of the caravan in the same manner.
Operating manual and inspection booklet Overview 5 Overview General This section provides an overview of the caravan body and its equipment. The arrangement and important control elements of the built-in devices are explained. NOTE Some of the built-in items described here are only available on express special option, or as accessories.
Operating manual and inspection booklet Overview 5.1 Caravan body General This section introduces the caravan body and provides examples of the location and function of specific elements and built-in units. 5.1.1 Keys With your caravan you receive three copies of the same key. This key can open the following locks: ...
Page 51
Operating manual and inspection booklet Overview A waste container can be found on the inside of the entry door. Sliding blinds are installed on the inside of the door's window. Optionally, the entrance can be provided with a fly-screen door, which is attached on the inside of the side wall.
Page 52
Operating manual and inspection booklet Overview Exterior door lock, body door To open the entry door, unlock the door lock with the key, reach into the recessed grip and pull the door to the outside. Fig. 14: Door lock Interior door lock, body door Opening and closing the entrance door To lock and secure the entrance door from inside:...
Page 53
Operating manual and inspection booklet Overview Rotate inner knob (2) upward until two pins (3) protrude to additionally secure the door. Fig. 17: Door closed and secured To open the door, simply push the lever downward Fig. 18: Door lock open...
Operating manual and inspection booklet Overview 5.1.3 Door and hatch locks CAUTION Open hatches can cause damage! Open hatches can hit street signs, light poles, and other obstacles while driving and cause severe damage to the vehicle and third-party properties. •...
Page 55
Operating manual and inspection booklet Overview Service compartment lock The service locks can be operated with the body door key. They are not operated via remote control. Opening the service compartment: Use the key to unlock the lock and clockwise rotate the knob ...
Page 56
Operating manual and inspection booklet Overview Gas cylinder box, EXQUISIT VIP The gas bottle locker is located in the front above the draw-bar. The gas bottle holder and the gas pressure regulator are located here. NOTE Depending on the selected equipment, a gas pressure regulator set (optional) with automatic switch-over function can be pre-mounted.
Operating manual and inspection booklet Overview 5.1.4 Window Hinged window The living and sleeping area features large hinged windows designed to provide superior ventilation. To open, turn the sash fastener fitted at the lower frame and slightly push the window to the outside until the support arms latch.
Page 58
Operating manual and inspection booklet Overview In the ventilation position, the sash fastener is positioned centrally in the clamping block. Fig. 26: Ventilation position In the closed position (sash fastener position for driving) the sash fastener is located on the inside of the clamping block. Before driving, it must be ensured that all sash fasteners are in the closed position (Fig.
Page 59
Operating manual and inspection booklet Overview Kitchen window Depending on the selected model and fittings, the kitchen area features a sliding window (optional) or a hinged window that must be opened during cooking to ventilate the interior. Opening and closing the sliding window ...
Operating manual and inspection booklet Overview 5.1.5 Combination blinds Combination blind The hinged windows are fitted combination blinds consisting of a fly screen and a blackout blind. Both blind components are hung from the window top. For both blinds: To close, use the handle to pull the fly screen fully downward and slightly push against the window until the lower strip latches.
Operating manual and inspection booklet Overview 5.1.6 Air conditioning system (optional) As a special option, a special attachment air conditioner is available to regulate the room temperature of the interior. In summer operation the air conditioner generates dehumidified cool air. In winter operation it generates supplemental warm air, without, however, replacing the heater of the vehicle.
Page 62
Operating manual and inspection booklet Overview Models Model variants Fig. 32: Skylight (Heki 2) Fig. 33: Skylight 400x400 mm VisionStar 700x500 mm Fig. 34: Prop-up skylight Fig. 35: Midi Heki / Mini Heki plus...
Operating manual and inspection booklet Overview 5.1.8 Pop-up roof (optional) DANGER Safety instructions Life-threatening danger due to lightning! During a thunderstorm, any persons in the pop-up roof can suffer life-threatening injury. • Never stay in the pop-up roof during thunderstorms. WARNING Danger of injury due to falling! When sleeping, playing, or if they are in the pop-up...
Page 64
Operating manual and inspection booklet Overview Upon request, a pop-up roof manufactured from fibre-glass reinforced plastics (GFRP) can be installed in the roof. In pop-up status, it offers two additional sleeping berths. The pop-up roof features a large bed pad with slatted frame, a skylight, a fly-screened ventilation window with protective rain cover (lockable from the inside), two transparent sheet windows with black-out blind, one supplemental vent with closing...
Operating manual and inspection booklet Overview NOTE Care tips Thoroughly vent the roof bellows several times during the season, to prevent stagnant moisture and musty smells. Do not fold the pop-up roof in damp or wet condition immediately after rainfall, for example. Prior to longer periods between use, remove the bed pad from the pop-up roof to avoid stagnant moisture and mildew.
Operating manual and inspection booklet Overview 5.1.10 Multifunction light switch Two multifunction switches are installed at convenient height in the entrance area. They control the various sources of light from inside and outside of the vehicle, permitting lighting the interior before entering the vehicle body.
Operating manual and inspection booklet Overview 5.1.12 LED switches and LED displays The LED switches and LED displays for the various 12V/230V consumers are arranged above the entrance. The number of switches and displays fitted in the control panel varies dependent on the specification.
Operating manual and inspection booklet Overview Figure Description Display Switch for floor heating On/Off switch: red = on Charger switch for stand-alone Left LED – charging status: package red = main charging phase yellow = full charge phase ...
Operating manual and inspection booklet Overview 5.2 Furnishings 5.2.1 Sitting area The shape and arrangement of the sitting area and table installed in the caravan depend on the model. Lower the table top to provide additional sleeping spaces (Section "Sitting and sleeping").
Page 70
Operating manual and inspection booklet Overview schbad Shower stall Depending on the floor plan and selected equipment, the bathroom contains a shower. It is surrounded by a shower curtain or a shower door that keeps water inside the shower. ATTENTION Material damage if the splash protection door is not locked in place when the vehicle is in motion! If the splash protection door is not locked in place...
Page 71
Operating manual and inspection booklet Overview Toilet The cassette toilet is installed next to the washbasin or the shower. Depending on the caravan's floor plan, the cassette toilet is either permanently installed or it rotates supported on bearings. For some floor plan models, a separate flushing water tank for permanently installed toilets is provided.
Operating manual and inspection booklet Overview Küchenbereich 5.2.3 Kitchen area The kitchen area is designed for longer stays. The kitchen counter area features a gas hob, sink and a small working surface. The gas hob and sink are covered with safety glass panels.
Page 73
Operating manual and inspection booklet Overview Refrigerator The refrigerator is in the kitchen area; it can be operated with 12 V, 230 V or gas. The model of refrigerator installed depends on the vehicle model. As a special option, a large refrigerator (optional) or a refrigerator/freezer combination (optional) can be installed.
Operating manual and inspection booklet Overview 5.3 Storage compartments 5.3.1 Storage space in the floor area WARNING Danger of accident and injury due to unsecured packed goods! Unsecured luggage and excessive load adversely affect driving behaviour; luggage can slide and cause serious accidents.
Operating manual and inspection booklet Overview 5.3.2 Wall cupboards Wall cupboards in the living area Additional storage possibilities are offered by the hinged compartments and open storage units e.g. above the sitting area as shown in the illustration. This is a good place to store items of common interest, such as games, maps, or magazines.
Operating manual and inspection booklet Overview Storage areas in the bathroom Cosmetics, toilet and hygiene articles can be stored in the storage shelves, and upper and lower cabinets in the bathroom. Additional storage space is provided by, for example, a mirror cabinet, if supplied with the model and selected equipment.
Operating manual and inspection booklet Overview 5.4 Technical equipment General Your caravan is equipped with modern and convenient technical systems. This section provides important information on the structure and function of the equipment and built-in devices. 5.4.1 Electrical system General The electrical system of the caravan is configured for 12 V and 230 V operation.
Page 78
Operating manual and inspection booklet Overview Power connection The power connection (Fig. 59) is located under a protective cover (1) at the outside of the caravan. Connect the CEE cable with the connection plug and secure with the stopping lever. NOTE Before travelling to foreign countries, obtain information about the plug and connector systems...
Page 79
Operating manual and inspection booklet Overview 12 V Emergency lighting If the 15 A plug-in fuse (1) is in its outer position, the power supply uses the standard setting with emergency lighting. 12 V Complete supply If the blind plug is removed and the 15 A plug-in fuse (1) is set to the left (3), the power supply uses the 12 V-complete supply setting.
Operating manual and inspection booklet Overview 5.4.1.1 Supply battery General You can use either a conventional lead/acid battery or a so- called AGM battery. The supply battery supplies all activated 12V consumers when the system is not connected to an external power source. Thus, the supply battery is continuously discharging.
Page 81
Operating manual and inspection booklet Overview AGM battery (optional) The AGM battery (absorbent glass mat) is a state-of-the-art battery that absorbs the electrolyte in a special fibre-glass matting. Lead-mat battery packs do not have a free sulphuric acid and can be operated in any position. The acid cannot escape even if the AGM battery breaks.
Page 82
Operating manual and inspection booklet Overview Stand-alone package (optional) The stand-alone package comprises a supply battery and a charger located beneath the housing. The supply battery supplies all 12 V consumers as soon as the 12 V main switch above the entrance door is switched on and the 12 V consumers are activated.
Page 83
Operating manual and inspection booklet Overview NOTE • The charger must only be installed and opened by authorised specialist personnel! • The device must be fully disconnected from the power source before the fuses are replaced! • Fuses must be replaced with fuses of the same fuse class and category! •...
Page 84
Operating manual and inspection booklet Overview ATTENTION Material damage due to improper maintenance! Improper maintenance of the battery will cause destruction and total failure of the unit! • Comply with manufacturer instructions. • Travel only with fully charged battery. • After every trip, recharge the battery for 12 hours.
Operating manual and inspection booklet Overview 5.4.1.2 Interior lighting LED spotlight In the interior, above the bench and in the sleeping area, there is a track light system with 12 V LED spotlights. Those can be rotated, pivoted and adjusted, allowing all areas to be well illuminated (for use see ...
Page 86
Operating manual and inspection booklet Overview Room spotlights Depending on the model and the selected equipment, there are either room spotlights with multiple rotating and pivoting LED lamps on a rail system, or permanently installed lights in the canopy. These are activated via a central ON/OFF switch. The light intensity can be regulated.
Page 87
Operating manual and inspection booklet Overview Canopy light (optional) The awning light (optional) lights up the entrance area at night. It can be operated with the remote control unit (optional) or the corresponding button on the entry door. The awning light must always be operated manually. For safety reasons, it does not switch off automatically and remains in operation until it is switched off.
Operating manual and inspection booklet Overview 5.4.1.3 Power outlets 230V outlet Outlets for the connection of small appliances when an external power supply is connected can be found at various locations in the vehicle interior, depending on the model and selected equipment (the picture shows an outlet in the support of the sitting area).
Operating manual and inspection booklet Overview 5.4.2 Gas supply General This section provides information about the gas supply system in the caravan. The installed gas appliances (depending on the selected equipment: heater, boiler, hob, oven, grill, refrigerator) - are explained in detail in the accompanying operating manuals provided by the respective manufacturers.
Page 90
Operating manual and inspection booklet Overview Gas cylinder box, EXQUISIT VIP The gas bottle locker is located in the front above the draw-bar. The gas bottle holder and the gas pressure regulator are located here. NOTE Depending on the selected equipment, a gas pressure regulator set (optional) with automatic switch-over function can be pre-mounted.
Page 91
Operating manual and inspection booklet Overview DuoControl CS gas supply (with Eis-Ex and remote display) (optional) A safety regulating system for gas pressure with integrated crash sensor is available at a surcharge for a two-bottle gas supply. It enables switching the gas bottle without interrupting the gas supply.
Page 92
Operating manual and inspection booklet Overview Remote display (optional) The remote display (optional) shows the gas consumption status in the vehicle interior (normal or reserve operation), as well as the heating operation of the regulator heater: After switching on, the display LEDs mean: ...
Operating manual and inspection booklet Overview 5.4.3 Heater General With the heating systems hot air heating and hot water heating are completely differentiated. With the Truma combination heater, the boiler is integrated for the first time, although is is hot air heating that is involved, so that a compact hot air heater (Truma-Combi) or a compact hot water heater (ALDE) are available alongside conventional hot air heating.
Page 94
Operating manual and inspection booklet Overview Hot-air nozzle To heat the caravan body, the blower drives hot air through the hot-air piping and expels the air through the hot-air nozzles into the caravan interior. To regulate the flow of hot air as needed, the hot-air nozzles installed at various points can be manually opened or closed.
Operating manual and inspection booklet Overview 5.4.3.2 ALDE- heater (optional) The ALDE heater (optional) with hot-water heater is a classic heating system similar to systems used in many households. It comprises a boiler operated with standard camping gas cartridges heating a glycol-water mixture and conveying the same into a closed circuit with convector elements (heating elements), recirculating pump and expansion vessel.
Page 96
Operating manual and inspection booklet Overview ALDE control unit Clock. The clock displays date and time (if activated). For its setting, please see the ALDE operating manual. Outside temperature*. The outside temperature is displayed. Interior temperature. The interior temperature is displayed. Recirculating pump.
Page 97
Operating manual and inspection booklet Overview ALDE window switch If the exhaust gas stack is installed below a window, an ALDE window switch is installed at the corresponding window. This unit is a contact switch automatically shutting down the heater when this window is opened, in order to prevent any exhaust gases from entering the vehicle interior.
Operating manual and inspection booklet Overview 5.4.3.3 Heat the floor with hot water (optional) A pipe system laid out under the floor with thermally conductive layers arranged on top serves as the floor heating system (optional). A special heating fluid (glycol/water mixture) circulates through the pipe system.
Operating manual and inspection booklet Overview Function switch of the floor heater system In combination with the TRUMA Combi heater, the function switches for floor heating are located above the entrance door. Fig. 88: Function switch (example) In combination with the ALDE hot water heater, the floor heating circuit can be switched on via a valve.
Operating manual and inspection booklet Overview 5.4.4 Fresh water and waste water system General The following section provides information on the fixtures for fresh water supply and waste water disposal. Fresh water intake port The fresh water fill pipe connection is outside on the side wall of the caravan.
Page 101
Operating manual and inspection booklet Overview Fresh water tank The fresh water tank is located in the living or sleeping area (shown in the Fig. under the bench seat of the sitting group as an example). Fresh water tank Cleaning cover Ventilation - fresh water tank Suction hose for the water pump Supply line to the level indicator...
Page 102
Operating manual and inspection booklet Overview Mixer tap WARNING Danger of scalding due to hot water! Hot water can scald hands and other body parts. • Open the mixer tap in cold-water position and carefully raise the temperature. To obtain water, turn the lever in direction of the cold-water setting (blue mark), lift upward, and slowly shift in direction of the red mark.
Page 103
Operating manual and inspection booklet Overview Waste water The waste water from sink and washbasin drains into a shared waste water conduit. Depending on the model and selected equipment, the waste water is either captured in a permanently installed waste water tank (optional), or discharged into the exterior.
Operating manual and inspection booklet Overview 5.4.5 Water heater ATTENTION Damages after extended stand time or frost! If the vehicle is not used in winter, the sanitary system may be damaged due to frost. Extended stand times can cause algae growth in the sanitary system.
Operating manual and inspection booklet Overview 5.4.5.1 TRUMA heater and TRUMA water heater system The TRUMA water heater is installed in the storage compartment under the bed. This hot water heater heats the water in three ways: When the gas heater is activated, a portion of the heated air ...
Operating manual and inspection booklet Overview 5.4.5.2 With installed ALDE heater (optional) The ALDE heater is fitted with a boiler (8.5 litre volume approximately). This boiler can be operated with liquefied gas or electric power. To fill the boiler, open the mixer tap for hot water. In general, the heating system can be operated with an empty boiler as well.
Operating manual and inspection booklet Camping 6 Camping This section describes the operation and function of the equipment of your caravan. See also the instructions provided in the "Overview" section and those in the operating manuals for the built-in devices. 6.1 Setting up the caravan 6.1.1 Establishing the power connection Before connecting, check whether the electrical supply...
Page 108
Operating manual and inspection booklet Camping Drain any residual water out of the fresh water tank ( section "Draining fresh water"). Open the fresh water intake port at the vehicle side. – Hold the twist cap firmly with one hand, insert the caravan body key into the lock and turn the key 180°.
Operating manual and inspection booklet Camping 6.1.3 Draining fresh water Open the drain valves for cold and hot water. Open the mixer taps of sink and washbasin. Open the service cover at the fresh water tank. Remove the drain plug. Completely drain the water from the fresh water tank.
Page 110
Operating manual and inspection booklet Camping Open safety drain valve manually: To the top rotary switch (1) until it engages. A push- button (2), which is located at the bottom of the housing, will pop out ( observe applicable operating instructions). ...
Operating manual and inspection booklet Camping 6.1.4 Draining the waste water NOTE Cleaning agents, soaps, wash lotions and cosmetics contaminate the environment and ground water. • Never drain waste water in free nature, dispose only at the designated disposal points! •...
Page 112
Operating manual and inspection booklet Camping Waste water drain with permanently installed waste water tank (SW) Place a collection container below the drain pipe under the vehicle (or discharge into designated waste water system, if available). Open the draw-off tap (1) next to the waste water tank. Drain waste water from the tank (tank volume: 44 litres!), into the collection container (or directly into the waste water system).
Operating manual and inspection booklet Camping 6.1.5 Changing the gas bottle (standard) For the standard model of the gas system (flexible gas hose and pressure reducer) change the gas bottle as follows: WARNING Danger of explosion and injury due to gas! Escaping gas can cause poisoning and explosions.
Operating manual and inspection booklet Camping 6.1.6 Replacing the gas bottle (DuoControl CS) (optional) In Control CS (with Eis-Ex and remote display)comply with the following instructions: WARNING Danger of explosion and injury due to gas! Escaping gas can cause poisoning and explosions. •...
Page 115
Operating manual and inspection booklet Camping Screw the union nut of the burst hose safety-valve (3) on to the gas bottle valve using the supplied tool. Inspect the gas hose at the gas bottle valve, at the pressure regulator, and over the entire hose length: If it leaks, is porous or damaged, do not operate the gas bottle! The gas hose must be replaced by specialised personnel.
Page 116
Operating manual and inspection booklet Camping Setting the remote display (optional) If a remote display has been installed in the vehicle interior, select the operating mode by activating the switch in the centre: Summer operation Winter operation The illuminated displays in the ornamental ring mean: ...
Operating manual and inspection booklet Camping 6.1.7 Gas supply maintenance (general) Repeat the gas supply inspection pursuant to applicable regulations (every two years in Germany, for example). Replace the gas pressure regulator set and the hoses at the latest ten years after their manufacturing dates.
Page 118
Operating manual and inspection booklet Camping Hinged window Intensive airing Turn the rotating knob upward by approximately 90°. Swing the window outward and latch in the desired position or fasten with the locking mechanism. To close the hinged window, swing further upward or undo the locking mechanism.
Page 119
Operating manual and inspection booklet Camping Combination blind The hinged windows are fitted combination blinds consisting of a fly screen and a blackout blind. Both blind components are hung from the window top. For both blinds: To close, use the handle to pull the fly screen fully downward and slightly push against the window until the lower strip latches.
Page 120
Operating manual and inspection booklet Camping Fly screen door (optional) The entrance door can be fitted with an optional fly screen door (optional). To open the screen door, push the handle into the desired position. To close the screen door, push the handle back. Fig.
Page 121
Operating manual and inspection booklet Camping Skylight Depending on the caravan model, the skylights installed in the roof differ in design and operation. Opening the prop-up skylight Grasp both handles to push the internal locking levers. Grasp both handles and push the skylight upward. Closing the prop-up skylight Grasp both handles to push the internal locking levers.
Operating manual and inspection booklet Camping Operate the lift skylight (optional) Push the safety button on both knobs (1, left and right) and rotate the knobs approximately 90°. Pull the clip (2) with a slight jerk from its bracket and swing downward.
Page 123
Operating manual and inspection booklet Camping Start-up Gas heater with automatic ignition Open the gas bottle and the quick-action valve in the gas feeding line. Turn the multi-function thermostat (1) to one of the thermostat settings 1 – 5 and push until the stop. The Fig.
Page 124
Operating manual and inspection booklet Camping Room thermostat The room thermostat regulates the heater output according to the setting at the thermostat installed at the heater's top. NOTE The temperature sensor is installed at the bottom of the heater. Cold droughts, door gaps, carpeting, etc. affect the thermostat action.
Page 125
Operating manual and inspection booklet Camping Removing the heater grille Slightly pull the heater grille top forward. Push up the retaining springs at the sides and tilt the heater grille forward (Fig. 128). NOTE If space is sparse, pull the heater grille top slightly to the front and lift until it is free.
Page 126
Operating manual and inspection booklet Camping Cleaning Prior to every heating period, use a small brush or paint brush to remove the dust accumulated on the heat exchanger, the bottom plate and the fan wheel. Hot-air nozzle To heat the caravan body, the blower drives hot air through the hot-air piping and expels the air through the hot-air nozzles into the caravan interior.
Operating manual and inspection booklet Camping 6.3.2 ALDE- heater (optional) Liquefied gas operation Select "Liquefied gas mode" at the operating unit. Open the gas shut-off valve for the heater. Start the heater. When you start the heater, the system automatically ignites the burner, NOTE The heater is active until the set temperature has...
Page 128
Operating manual and inspection booklet Camping Operating the ALDE control unit NOTE • Switch off the heating system's main switch when the vehicle is not used. • Don't splash water directly at the exhaust chimney when you wash the vehicle. •...
Page 129
Operating manual and inspection booklet Camping Idle position Clock. The clock displays date and time (if activated). For its setting, please see the ALDE operating manual. Outside temperature*. The outside temperature is displayed. Interior temperature. The interior temperature is displayed. Recirculating pump.
Page 130
Operating manual and inspection booklet Camping Setting the required temperature You can set the temperature in increments of 0.5 °C between +5 °C and +30 °C. You cannot adjust the temperature if the day or night automatic are active. The plus and minus symbols are displayed in grey.
Page 131
Operating manual and inspection booklet Camping Normal mode. If fresh water is added and you want hot water, press "+" (the symbol is filled to the middle). You cannot select this function if the pump is in continuous operation mode. Fig.
Page 132
Operating manual and inspection booklet Camping Heating with gas If you select electricity and gas at the same time, you can set the priority for either electricity or gas (see the ALDE operating manual). Press the "liquefied gas flame" symbol to start the gas mode. The symbol for liquefied gas becomes active and changes to green.
Page 133
Operating manual and inspection booklet Camping Tools menu Open the Tools menu from the Main menu. In the Tools menu, you can change the remaining functions of the operating unit. Click the "wrench" symbol in the Settings menu to open the Tools menu.
Operating manual and inspection booklet Camping 6.3.3 Water heater ATTENTION Damages after extended stand time or frost! If the vehicle is not used in winter, the sanitary system may be damaged due to frost. Extended stand times can cause algae growth in the sanitary system.
Operating manual and inspection booklet Camping 6.3.3.1 TRUMA heater and TRUMA water heater system Filling the hot water heater Fill the cold water tank ( "Filling with cold water"). Turn on main switch (power supply). Close cold and hot water drain valves. Open mixer tap in kitchen or bathroom in "hot water"...
Operating manual and inspection booklet Camping Operating the hot water heater The water heating system (SW) is activated with the On-Off switch (1). It is located above the entrance door. The water heating system does not require maintenance. Fig. 150: On-Off switch of the water heating system 6.3.3.2 With installed ALDE heater (optional) Close the combined drain valve at the freshwater tank.
Operating manual and inspection booklet Camping 6.4 Sitting and sleeping 6.4.1 Converting the sitting area The layout of the sitting area depends on the selected model. By lowering the table, you can create additional sleeping spaces. Lowering a table with support leg Push the sliding bush (1) upward and fold the lower part of the table leg (2).
Page 138
Operating manual and inspection booklet Camping "Ilse-Lift" lifting frame (optional) Functions: Lowerable single leg table foot Rotating table plate Raising the table Swivel operating lever (2) through 180 degrees. The table automatically raises to its normal position. Once the desired height of the tabletop is reached, lock the operating lever again Rotating the tabletop ...
Page 139
Operating manual and inspection booklet Camping “Click-clack” lifting frame (optional) Functions: Lowerable single leg table foot Rotating table plate Raising the table Raising of the table by pressing the table plate twice (pressing releases the lock = click, pressing down = clack) Swivelling the table plate ...
Operating manual and inspection booklet Camping 6.4.2 Folding console as bed extension Depending on the model, a folding console may be installed as an extension of the bed. Fig. 156: Folding console as bed extension Folding the folding console Push both latches (1) upward at the same time and fold the console downward.
Operating manual and inspection booklet Camping 6.4.3 Sitting group conversion to a sleeping area The free surfaces must be padded out with additional (optional) cushions to provide a continuous sleeping surface. Fig. 158: Round sitting group The round seating group is padded out with additional (optional) cushions.
Page 142
Operating manual and inspection booklet Camping Dinette with hook-in table Fig. 160: Table with hinged table foot Raise table, fold in hinged table foot. Fig. 161: Table foot folded in...
Page 143
Operating manual and inspection booklet Camping Raise the table further until it can be taken out of the upper rail and hook back into the lower rail. Fig. 162: Hook table into lower rail. Pad out the free surface with additional cushions (optional). Pull the seat cushion out to the table and turn over a back cushion to obtain a closed sleeping surface.
Operating manual and inspection booklet Camping 6.4.4 Setting up the lighting Depending on the selected model and equipment, the living and sleeping areas are fitted with various lamps. Adjusting brightness The brightness of the living area lamps can be adjusted as required.
Operating manual and inspection booklet Camping 6.4.5 Opening and closing the pop-up roof DANGER Safety instructions Life-threatening danger due to lightning! During a thunderstorm, any persons in the pop-up roof can suffer life-threatening injury. • Never stay in the pop-up roof during thunderstorms.
Page 146
Operating manual and inspection booklet Camping NOTE Care tips Thoroughly vent the roof bellows several times during the season, to prevent stagnant moisture and musty smells. Do not fold the pop-up roof in damp or wet condition immediately after rainfall, for example. Prior to longer periods between use, remove the bed pad from the pop-up roof to avoid stagnant moisture and mildew.
Page 147
Operating manual and inspection booklet Camping Park the vehicle in a position appropriate to the prevalent wind situation. Remove any loads on the roof. Open the access hatch. Assemble both parts of the access ladder and interlock the components (Fig. 166/1). Hang the access ladder in the corresponding rail (Fig.
Page 148
Operating manual and inspection booklet Camping Folding the pop-up roof Fully close the venting windows and zips. Open the roof canopy to prevent overpressure in the pop-up roof during the folding process. This would push the expansion bellows to the outside. CAUTION Risk of injury when exiting! Jumping from the pop-up roof may cause injuries due...
Operating manual and inspection booklet Camping Sanitäörbereich 6.5 Bathroom 6.5.1 Using the shower and washbasin The shower and washbasin are supplied by the heating system or a hot water boiler (optional). Activate the mixer tap to draw hot water. Toilettenspülung Thetford 6.5.2 Flushing the toilet with fixed installed toilets (optional) Before flushing, open the slide gate of the waste holding...
Page 150
Operating manual and inspection booklet Camping Emptying the waste holding tank NOTE The waste holding tank must be emptied at the latest when the fill level indicator next to the flushing button is illuminated. Completely empty the holding tank if there is danger of freezing and the caravan superstructure is not heated.
Operating manual and inspection booklet Camping Toilettenspülung Thetford 6.5.3 Flushing the toilet with revolving toilets (optional) Manually rotate the toilet seat in closed state into the desired position. To flush, turn the lever (1) at the toilet bowl side counter- clockwise.
Page 152
Operating manual and inspection booklet Camping NOTE The waste holding tank must be emptied at the latest when the fill level indicator next to the flushing button is illuminated. Completely empty the holding tank if there is danger of freezing and the caravan superstructure is not heated.
Operating manual and inspection booklet Camping 6.6 Kitchen area 6.6.1 Using the combination ceramic hob WARNING Burn injuries due to open gas flame! Improper operation can cause injury. • Prior to operation, open the kitchen window. • Never let gas escape without igniting. •...
Operating manual and inspection booklet Camping 6.6.2 Cooker controls Cooker controls (1) Control knobs of the burner, rear left (2), front left (3), front right (4) and rear right (5). Control switch for the grill (6) Ignition knob (7) Control switch (8) for temperature selection ...
Operating manual and inspection booklet Camping 6.6.3 Cooking The gas cooker is located under a safety glass plate. Lift the glass plate. Make sure that the gas cylinder or the gas supply is connected and switched on. If there is a smell of gas, switch off the gas cylinder/the main supply and contact the manufacturer.
Page 156
Operating manual and inspection booklet Camping NOTE Each burner supports pans and pots with a diameter of 10 to 22 cm; make sure that the device is not overloaded, as this could lead to reduced performance. We recommend the following maximum pot sizes: Electric plate:- Ø180mm Auxiliary burner:- Ø200mm Half-speed burner:- 2x Ø200mm or 1x...
Operating manual and inspection booklet Camping 6.6.4 Grilling Make sure that the gas cylinder or the gas supply is connected and switched on. If there is a smell of gas, switch off the gas cylinder/the main supply and contact the manufacturer. Switching on: Open the door, press down the control switch and set it to the highest level (see Fig.
Page 158
Operating manual and inspection booklet Camping With this burner it is normal for the flames to develop yellow tips when heating up. Switching off: Turn the control switch until the line on the switch is in line with the dot on the instrument panel. Always make sure that the control switch is in the OFF position when the grill is no longer in use.
Operating manual and inspection booklet Camping 6.6.5 Baking Make sure that the gas cylinder or the gas supply is connected and switched on. If there is a smell of gas, switch off the gas cylinder/the main supply and contact the manufacturer. Switching on: Open the door, press down the control switch and set to the highest level (240°C).
Operating manual and inspection booklet Camping 6.6.6 Folding console to extend the kitchen counter-top Depending on the model, a folding console may be installed as an extension of the kitchen counter-top. Fig. 187: Folding console to extend the kitchen counter-top Opening the folding console ...
Operating manual and inspection booklet Camping 6.6.7 Using the Thetford refrigerator (optional) NOTE Prior to first use and cleaning, and when parking for longer periods (e.g. winter break) read the accompanying operating manual provided by the manufacturer of the refrigerator! Overview The refrigerator can be operated with 12V, 230V or with gas.
Page 162
Operating manual and inspection booklet Camping Activating the refrigerator Press the ON-OFF switch (A) for one second. The integrated lamp illuminates green. The LED operating panel dims after ten seconds. The green lamp indicates that refrigerator is operating. Selecting the power source After activating the refrigerator, press the operating button (B) for two seconds.
Operating manual and inspection booklet Camping 6.6.8 Using the Domestic refrigerator (optional) General The refrigerator can be operated with 12V, 230V or with gas. To prevent discharging the supply battery, do not use the 12V battery when the engine is running. ...
Page 164
Operating manual and inspection booklet Camping Gas operation Open the glass bottle valve. Open the quick-action valve for the refrigerator. Press the energy selector switch (1) for approx. two seconds. Press the energy selector switch (1) several times until the operating mode display (3) shows gas operation.
Page 165
Operating manual and inspection booklet Camping Switching on the refrigerator with manual ignition Control elements Energy selector switch Temperature level regulator Ignition knob Gas operation display Fig. 193: Control elements on the refrigerator with manual ignition Electrical operation Switch the energy selector switch (1) to mains operation or battery operation.
Page 166
Operating manual and inspection booklet Camping Gas operation Open the glass bottle valve. Open the quick-action valve for the refrigerator. Switch the energy selector switch (1) to gas operation. Press the temperature level regulator (2), turn it to the desired cooling level and keep it depressed. To ignite, press the ignition knob (3).
Operating manual and inspection booklet Maintenance 7 Maintenance Proper care requires the right cleaner for the various materials. This applies to both the exterior and interior of the vehicle. To maintain an overview of the variety of materials used, we have compiled a list of the materials, their properties and the requirements for the appropriate cleaner in a table in the appendix.
Operating manual and inspection booklet Maintenance 7.1 Exterior cleaning NOTE Acrylic glass window panes are very sensitive and require special care. Only clean wet with a clean sponge or soft cloth. Avoid using chemical cleaning agents, glass cleaner and other aggressive cleaners. Use special acrylic glass cleaner for stubborn stains.
Operating manual and inspection booklet Maintenance 7.2 Interior cleaning Use standard, non-aggressive household cleaning and care products for the interior and floor. Wipe off furniture surfaces with a damp cloth, use furniture polish if necessary. Vacuum off the upholstery or clean it carefully with a mild foam cleaner.
Operating manual and inspection booklet Maintenance 7.4 Supply battery (optional) Check the charge status of the supply battery (if purchased), recharge if necessary (see "Overview"). NOTE The caravan is delivered with a maintenance-free supply battery that does not require special care. If a different type of rechargeable battery has been used when changing rechargeable batteries, the following steps are required:...
Operating manual and inspection booklet Maintenance 7.5 Preparing the caravan for periods of non-use Take the following measures. Supplemental tasks for winter care are indicated by the letter Amend this list to meet your specific requirements. Component Activity Chassis Park the caravan where it is safe and secure it from rolling off.
Page 172
Operating manual and inspection booklet Maintenance Component Activity Electrical system Check the supply battery (optional), fill, recharge if necessary. Remove the supply battery (optional) and store it in a frost-free location. Spray contact spray into the contacts of the plug connector for connection to the towing vehicle.
Operating manual and inspection booklet Maintenance and inspection 8 Maintenance and inspection General Maintenance tasks described in the sections below are required for optimal and trouble-free vehicle operation. If increased wear is determined on specific components in regular inspections, shorten the required maintenance interval based on the actual indications of wear! In addition to this operating manual, the operating manuals supplied for the built-in devices also apply.
Operating manual and inspection booklet Maintenance and inspection 8.1 Maintenance schedule Interval Component Action required Weekly Supply battery (optional) Check charge status Monthly Main switch (FI) Function check Tyres Check the tyres: Condition, tread depth, fill pressure Fresh water tank and fresh Clean and disinfect water system Blackwater tank and waster...
Operating manual and inspection booklet Maintenance and inspection Interval Component Action required annually Electrical system Function check Fresh water and waste water Function check, leak test system Heater, boiler, gas cooker Function check Lighting, refrigerator Function check Gas burner, refrigerator Have them cleaned by an authorised workshop Seals on the doors, storage Function check...
Operating manual and inspection booklet Maintenance and inspection 8.3 Wheels and tyres General WARNING Danger to life due to incorrect tyre pressure! Incorrect tyre pressure causes excessive wear and tear and damages the tyre which ultimately could burst. • Prior to every trip or in two-week intervals, check the tyre pressure in cold tyres.
Page 177
Operating manual and inspection booklet Maintenance and inspection Regularly check tyre bolts and nuts for proper seating. Re- tighten the nuts or bolts of a replacement after 50 km driving (crosswise sequence, see Fig. 195). See section "Tightening torques" for the correct tightening torque.
Page 178
Operating manual and inspection booklet Maintenance and inspection The weight is governed by the maximum permissible axle load to be distributed over two tyres (do not load one-sided). The maximum bearing capacity of a tyre is specified by its load index (= LI load bearing capacity identifier).
Page 179
Operating manual and inspection booklet Maintenance and inspection Treating tyres properly Drive over curbs at an obtuse angle. The tyres may possibly be jammed at the flank. Driving over curbs at an acute angle may cause damage to the tyre and subsequently bursting. ...
Operating manual and inspection booklet Maintenance and inspection 8.3.1 Changing wheels General The spare wheel (optional) is stored in the draw-bar box. Use an off-the-shelf scissor jack to change wheels. WARNING Danger to life due to rolling or falling of the vehicle! Severe injuries can be the result if the vehicle rolls or falls when a wheel is changed.
Page 181
Operating manual and inspection booklet Maintenance and inspection Do not damage the thread of the gudgeon when changing wheels. Always tighten tyre nuts and bolts crosswise. If you switch to different rims (e.g. aluminium rims or winter tyres), use the corresponding wheel bolts with correct length and head shape.
Page 182
Operating manual and inspection booklet Maintenance and inspection Preparing the coupled caravan In caravan couplings with a stabilisation device, loosen the stabilisation device. The friction linings will be overstressed otherwise. Engage the parking brake of the towing vehicle and shift to first gear.
Page 183
Operating manual and inspection booklet Maintenance and inspection Procedure To secure the vehicle, use wheel chocks or similar object on the opposite wheel (Fig. 197). Remove the spare wheel (optional) from its bracket. In the case of soft ground, place a stable base (e.g., wooden board) under the jack.
Operating manual and inspection booklet Maintenance and inspection 8.3.2 Tyre pressure table Tyre type Technically permissible total weight [kg] for Tyre pressure [bar] vehicles with Single axle Tandem axle 185/70 R14 LI88 ≤ 900 1800 2.60 1000 2000 2.80 1100 2200 2.80 185 R14C LI102...
Page 185
Operating manual and inspection booklet Maintenance and inspection Tyre type Technically permissible total weight [kg] for Tyre pressure [bar] vehicles with Single axle Tandem axle 195/70 R14XL LI96 ≤ 900 1800 2.50 1000 2000 2.50 1100 2200 2.50 1200 2.70 1300 2500 3.00...
Page 186
Operating manual and inspection booklet Maintenance and inspection Tyre type Technically permissible total weight [kg] for Tyre pressure [bar] vehicles with Single axle Tandem axle 205 R14C LI109 ≤ 1600 3.70 1700 4.00 1800 3500 4.25 1900 4.50 215/55 R16XL LI97 ≤...
Page 187
Operating manual and inspection booklet Maintenance and inspection Tyre type Technically permissible total weight [kg] for Tyre pressure [bar] vehicles with Single axle Tandem axle 215/55 R17XL LI98 ≤ 1400 3.20 215/60 R17C LI109 ≤ 1700 4.00 1800 4.50 1900 4.50 2000 4.75...
Operating manual and inspection booklet Maintenance and inspection 8.4 ALDE heating maintenance overview Date Maintenance task Distributor or service centre Changing the glycol/water mixture Heating system vented in cold state Heating system vented in warm state Stamp, signature ...
Page 189
Operating manual and inspection booklet Maintenance and inspection Date Maintenance task Distributor or service centre Changing the glycol/water mixture Heating system vented in cold state Heating system vented in warm state Stamp, signature Changing the glycol/water mixture ...
Operating manual and inspection booklet Malfunctions 9 Malfunctions General This chapter provides information about troubleshooting. Malfunctions for which causes and remedies are not explained here must be corrected by an authorised workshop. Additional information concerning malfunctions is also provided in the operating manuals for the built-in devices. If the malfunction correction measures described in those manuals are not successful, then contact an authorised workshop.
Operating manual and inspection booklet Malfunctions 9.2 Electrical system DANGER Life-threatening danger due to electric shock! Touching live components can cause serious or fatal injury. • Prior to any work, switch off the electrical system and disconnect from the mains supply. •...
Operating manual and inspection booklet Malfunctions 9.2.2 Faults of the stand-alone package (optional) Malfunction Cause Remedy Supply battery does not charge Charger defective Contact a specialist workshop with 230 V connection Charging current fuse defective Identify the defect and correct it; if necessary, visit a workshop, then replace the fuse 12 V power supply does not work...
Operating manual and inspection booklet Malfunctions 9.2.3 Changing light bulbs DANGER Life-threatening danger due to electric shock! Danger of electric shock potentially resulting in serious or fatal injury when working on electrical equipment. • Any repair tasks on the electrical system must be performed by qualified personnel.
Page 194
Operating manual and inspection booklet Malfunctions Replacing the bulb of the rear lamp unit Pull the chrome strip (A) off from the rear lamp assembly towards the rear. Fig. 201: Rear lamp assembly mounting Use a screwdriver to remove the screws (1) of the rear lamp assembly.
Operating manual and inspection booklet Malfunctions 9.2.4 Changing the smoke detector battery The smoke detector is fitted with a 9 V block battery. To maintain the function of the smoke detector, the block battery must be replaced regularly, at the latest when the battery indicator signal sounds.
Operating manual and inspection booklet Malfunctions 9.3 Gas supply WARNING Danger of injury due to escaping gas! Escaping gas can explode. • All repair work must be performed by an authorised gas specialist workshop. • If gas odour is detected: –...
Operating manual and inspection booklet Malfunctions 9.5 Heater and hot water 9.5.1 Malfunctions, TRUMA heater Malfunction Cause Remedy Red indicator light, "Malfunction", Lack of gas Open the gas bottle valve and is illuminated quick-action valve Connect a full gas bottle Air in the gas line system Switch off the heater and switch it on again.
Operating manual and inspection booklet Malfunctions 9.5.2 Malfunctions, ALDE heater Malfunction Cause Remedy Battery low Battery voltage in vehicle below Charge battery (automatic reset 10.5 V (heater shuts down) as soon as the voltage is again above 11 V) Fan failure Wrong fan speed Automatic reset after 5 minutes Gas failure...
Operating manual and inspection booklet Malfunctions 9.6 Refrigerator Malfunction Cause Remedy Refrigerator does not switch on: at 230 V mains operation Circuit breaker has tripped Determine the defect and correct it; if necessary go to a workshop, then switch on the circuit breaker. 230 V operating voltage is too Have the 230 V system checked by a specialised workshop...
Operating manual and inspection booklet Malfunctions 9.7 Fresh water and waste water system Malfunction Cause Remedy Water leaks in the vehicle Fresh water system or waste Identify leak points, repair the water system leaks leaks No fresh water Freshwater tank empty Fill the fresh water tank Water pump fuse defective Identify the defect and correct it;...
Operating manual and inspection booklet Index 11 Index A Extending and retracting the support elements 47 Adjusting the LED spot light 144 Exterior cleaning 168 AGM battery 81 F Air-conditioning 61 Filling levels 99 Airing 117 Fire safety 15 ALDE heater 95, 127 Floor heating 99, 126 Appendix 201 Flushing the toilet 149, 151...
Page 205
Operating manual and inspection booklet Index H Malfunction 190 Hatch lock 51 Stand-alone package (optional) 192 Hatch locks 54 Malfunctions Heater 93, 95 cooking hob 196 Heating 122 electrical system 191 Heating the floor 98 fresh water and waste water 200 Hinged window 57, 118 gas supply 196 Locking 57...
Page 206
Operating manual and inspection booklet Index electrical 26 Technical documentation 8 fire safety 15 Technical equipment 77 gas devices 24 Toilet 71 gas supply 23 Toilet chemistry 31 general requirements 14 Traffic safety 16 on the road 22 Trailer 17 Rig operation 17 Travelling and parking 44 sanitary system 29...
Page 208
LMC CARAVAN GMBH & CO. KG Rudolf-Diesel-Straße 4 D-48336 Sassenberg T +49 (0) 2583 / 27-0 E info@lmc-caravan.de H www.lmc-caravan.de Münster (Westf.): HRB 9914 USt-IdNr. 126 733 941 Geschäftsführer: Bodo Diller, Timo Ecke, René Ricken...
Need help?
Do you have a question about the EXQUISIT VIP and is the answer not in the manual?
Questions and answers