Related Manuals for Ijinus LOG03V4-2G/4G LTE
Summary of Contents for Ijinus LOG03V4-2G/4G LTE
- Page 1 Installation guide LOG03V4- : Wireless data logger 2G/4G LTE 2x analog inputs (4-20mA) 2x digital inputs: contact or counter 100 Hz 1x power supply input (5V...30V) 1x open collector output 1x voltage output (5V...18V)
-
Page 2: Table Of Contents
Setting up a Sim card ............................32 Battery replacement ............................. 33 Revision of the document ............................. 35 IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 3: Introduction
First, connect the battery (details in chapter 4.3) and insert the sim card (beveled side-up, details in chapter 4.2) on its holder. 3 Configuration of the logger using the software Avelour IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 4: Necessary Equipment
If a different power supply is needed for the external sensor, you can change the supply voltage in the Avelour software. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 5: Run Avelour And Connect To The Sensor To Configure
The firmware update process can last a moment. On-site, prefer the best radio connection signal (like opening the metal cover of a sewer manhole). IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 6: General Information And Name Of The Logger
The most important information would be the name that will help to find the sensor at a future connection. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 /... -
Page 7: Applications
First, click on the "Add a measure" button, then choose the "Wired overflow detector" application. The configuration table open up : Choice of the contact IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... - Page 8 If you click on the "No" button, it becomes "Yes" and the "reset infinite counter" option appears. Clicking on the "Execute" button clears the accumulation and resets the totalizer to zero. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 9 After few seconds, a pop-up window appears to indicate that the configuration has been saved successfully in the logger. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 10 Installation guide K0J00121 Quick programming using Avelour IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 11: Application : Bucket Toggles Record
If it is another rain gauge, you must use an IJINUS cord with M12 connector and bare wire ends and connect the 2 wires of your rain gauge to the GND (brown wires of the IJINUS cord) and to the digital input 1 (pink wire of the IJINUS cord) or to the digital input 2 (blue wire of the IJINUS cord). - Page 12 After a few seconds, a screen appears to indicate that the settings have been successfully saved in the data logger. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 13: Application : Cumulative Rainfall
If it is another rain gauge, you must use an IJINUS cord with M12 connector and bare wires and connect the 2 wires of your rain gauge to the GND (brown wire of the IJINUS cord) and to the digital input 1 (pink wire of the IJINUS cord) or to the digital input 2 (blue wires of the IJINUS cord). - Page 14 This cumulative total is calculated on a rolling basis and is therefore updated each time cumulative rainfall is measured, according to the defined counting period. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 15 It is possible to trigger a measurement to find out the value of the infinite total recorded on the data logger. Advanced parameters The “View advanced parameters” button reveals more options and functionalities : IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 16 You must save the configuration by clicking on the “Save configuration” button, to send it to the logger’s memory. After few seconds a confirmation appears: IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 17: Application : Lift Station
This section describes how to configure your logger. First, click on the "Add" button, then choose the " Lift station " application. The configuration table for this application opens : IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... - Page 18 "More information on functioning". L'exemple ci-après s'ouvre dans un document au format pdf : - Choice of the Reporting period IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 19 You must save the configuration by clicking on the “Save configuration” button, to send it to the logger’s memory. After few seconds a confirmation appears: IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 20: Application : 4-20 Ma Measure
IJINUS cable for current input 1 and grey wires from the IJINUS cable for current input 2). NON-POWERED ANALOGUE PROBE If it is a probe supplied by IJINUS, you must connect the M12 lead of your probe to your data logger. Probes supplied by IJINUS are wired by default to the "4-20 mA input" (18). - Page 21 + to the datalogger's voltage output (green wire from the IJINUS cable). You must then connect the current output - of the probe to the current input of the logger (yellow wires of the IJINUS cable for current input 1 and grey wires of the IJINUS cable for current input 2).
- Page 22 Adjustment value : the sensor connected to the logger can be calibrated by using the "Adjustment value" IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 23 Advance parameters The " Show advanced parameters " button allows you to access more functionalities : IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 24 You must save the configuration by clicking on the “Save configuration” button, to send it to the logger’s memory. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 25 Installation guide K0J00121 Quick programming using Avelour After few seconds a confirmation appears: IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 26: Data Sending By Gprs Communication
The cellular antenna has also to be connected to the connector on top of the logger. - Set now the time zone in the System options menu: IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... - Page 27 Before forcing a data sending, click on “Program the device” button to send the configuration in the logger memory. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 28 Options will appear as the PPP options in the modem options. You need to fill in your own information details regarding your server access. Your server administrator can provide to you this information. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
- Page 29 After completing this chapter, please press the Program the devise button, the configuration will be sent by radio to the sensor. After few seconds a confirmation appears: IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 30: Local Data Reading In Real Time And Data Download
You can view the data, even offline, on graphic and list. A graph configuration module allows you to change colors, thickness of lines, …, but also to apply statistical filters and formula to your data. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 31: Data Export
From the graph and/or list of data you find the tab “Export the measures” with the choice of different files format and style of reports, from date to date, by month, or simply all data. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 32: Maintenance
USB, in order to recognize the SIM card. - Unscrew the protective ring and remove the cover. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com... -
Page 33: Battery Replacement
IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 /... - Page 34 The battery voltage returns to 3.65 V and the gauge to 0 mAh, information that can be accessed from the 'Windows' menu, then 'Device properties'. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
-
Page 35: Revision Of The Document
V3 Loggers D. MAHE 03/10/2023 2A02 V4 Loggers A. TRIBALLIER D. MAHE 07/11/2024 2A03 Avelour 7.1 A. TRIBALLIER IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC - France - – Customer Service: +33 2 98 09 03 32 / sav@ijinus.com...
Need help?
Do you have a question about the LOG03V4-2G/4G LTE and is the answer not in the manual?
Questions and answers