Evenheat V8 Assembly And Operating Manual
Vitrigraph floor stand
Hide thumbs
Also See for V8:
- Installation and operating manual (18 pages) ,
- Installation and operating manual (9 pages) ,
- Assembly and operating manual (11 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Evenheat V8
Summary of Contents for Evenheat V8
- Page 1 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Page 1 of 16...
- Page 2 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Assembly Instructions Tools needed: 7/16” Wrench T-20 Torx Wrench (included) Place stand base on floor with threaded holes up and visible. Page 2 of 16...
- Page 3 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Place the larger stand upright over the holes in the stand base Page 3 of 16...
- Page 4 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Attach the larger stand upright to the base by threading in a bolt with lockwasher into each of the 6 holes. Do not tighten bolts until all 6 are in place and are at least partially threaded in. Once all 6 bolts are threaded in you may tighten them using a 7/16”...
- Page 5 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Place the smaller, upper upright over the holes in the lower upright. Page 5 of 16...
- Page 6 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Support Plate Page 6 of 16...
- Page 7 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Place Support Plate as shown Attach support plate and upper upright to the lower upright by threading in a bolt with lockwasher into each of the 4 holes. Do not tighten bolts until all 4 are in place and are at least partially threaded in. Once all 4 bolts are threaded in you may tighten them using a 7/16”...
- Page 8 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Place the mounting plate onto the 4 screws located at the top of the uprights. Tighten screws with included T-20 wrench. Page 8 of 16...
- Page 9 1/4” Hinge Rod and Speed-nut Install the V8 kiln base to the mounting plate using the 1/4" hinge rod. To do so line up holes located in the V8 kiln base with holes in the mounting plate and insert rod. Push the rod all the way through the 4 holes until the bent portion of the hinge rod makes contact with the V8 kiln base and stops.
- Page 10 Assembly and Operating Manual May 2024 Install a speed-nut onto the un-bent end of the rod and push it on until it makes contact with the V8 kiln base. We have included an extra speed-nut in case you lose one.
- Page 11 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 You may now allow the V8 kiln base to fold down and hang. Page 11 of 16...
- Page 12 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Place the tool rest shelf (optional) onto the 4 screws located on the right side of the stand upright. Tighten screws with included T-20 wrench. Place the cane/rod holders (optional) onto the 4 screws located at the bottom center of the upright. Tighten screws with included T-20 wrench.
- Page 13 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Rotate the V8 kiln base upwards and secure it in the horizontal position using the 2 arms located on the mounting plate. Page 13 of 16...
- Page 14 V8 Vitrigraph Floor Stand Assembly and Operating Manual May 2024 Assembly of the V8 Vitrigraph floor stand is now complete. Page 14 of 16...
- Page 15 Place the kilns firebrick floor onto the stands V8 kiln base with the band clamps facing the back and the front of the floor making contact with the front lip on the V8 kiln base. This ensures that the glass exit hole in the floor lines up over the glass exit hole in the V8 kiln base.
- Page 16 When the floor stand is not in use it’s possible to lower the kiln base to get it out of the way. To do so remove the V8 Vitrigraph kiln from the stand entirely and unhook the arms supporting the V8 kiln base and allow it to rest in the down position.
Need help?
Do you have a question about the V8 and is the answer not in the manual?
Questions and answers