Advertisement
Maintenance and care
Filters
Rotate
... check,
filter cylinder,
if required,
remove filter
clean.
system ...
Spray arms
pull lower arm
... Remove
upwards ...
blockages/
deposits.
Rectifying minor faults yourself ...
Fault
Possible causes
Display "6" is lit
Supply fitting jammed or calcified
Display "E:24"
Waste water hose is blocked
and "6" are lit
or kinked
Cover not attached to waste
water pump
Display "E:25"
Waste water pump blocked
and "6" are lit
Other fault display
Appliance has technical defect
"E:XX" is lit
Residual water
The programme has not yet ended
in the appliance
Rust on the cutlery
Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Terminating the programme ...
While the programme is running,
press the START button
for approx. 3 sec. (Reset).
For perfect rinsing results ...
rinse
under
running
water ...
unscrew
upper arm ...
... as it is worth doing it yourself!
Remedial action
Open supply fitting.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min.,
when water supply is open.
If the flow rate is less, replace the supply fitting.
Install supply hose without kinks.
Install waste water hose without kinks.
Attach cover (see above).
Clean waste-water pump (see above).
Call factory customer service (state fault display).
Unplug appliance.
Close the appliance and switch it on or terminate
the programme (see Terminating the programme).
Use dishwasher-proof cutlery.
Never wash rusting parts in the appliance.
The numerical display
indicates "0:01";
approx. 1 minute after
Switch off the appliance.
the programme ends,
"0:00" is indicated.
insert ...
insert
clean spray nozzles
lower arm ...
under running water
(if required
use toothpicks) ...
Fault
Possible causes
Utensils are not clean
Utensils are situated close together
or one above the other
Sand or gritty residue
Too little detergent
on the utensils
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Stains and streaks
Rinse aid dosage too high/too low
Rinse aid
Utensils not dry
The combined detergent used
has a poor drying performance
Appliance setting
Milky deposits
Water softening system incorrectly set
on the utensils
No salt
(can be removed)
Milky deposits, glasses
Glasses not dishwasher-proof
cloudy/tarnished
(cannot be removed)
Plastic/utensils
Too little detergent
discoloured
Discoloration caused by food colourings
(tomato sauce)
Loading the dishwasher correctly ...
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink
or adhesive labels; remove large remnants of jam, milk products and food
according to the operating instructions and check that the spray arms can rotate freely.
Cleaning waste water pump
Screw on
– Pull out the mains plug.
filter system
– Remove filters and scoop out water.
NOTE
– Lever off cover (A).
MARK!
– Check area around the fan impeller
for foreign objects.
– Click cover shut (B).
– Insert filters.
A
B
1
screw on upper
CLICK!
arm tightly
More information can be found in the operating instructions
Remedial action
Separate the utensils, prevent contact points.
Follow manufacturer's instructions (detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Streaks: reduce dosage.
Water or limescale stains: increase dosage.
Increase dosage.
Change the product.
Use rinse aid.
Activate intensive drying (depending on model).
Correctly set water softening system.
Refill with special salt.
Use dishwasher- proof glasses.
Use a detergent suitable for glasses.
Follow manufacturer's instructions (detergent).
Discoloration is harmless;
subsequent rinse cycles will cause it to fade.
3
2
Advertisement
