Advertisement
Part Components
A) Monitor and mount
B) Camera C) Accessories
A
iBEAM Vehicle Safety Sytems
®
Universal
Wireless 7" Monitor
and Commercial Camera
Visit
iBEAMUSA.com
for more detailed informatuon about the product and up-to-date vehicle specific
applications.
Product Features
• Wireless HD camera and monitor kit
• 7" LCD Monitor
• 90 M / 300 FT range
• DC socket for monitor power with power button for easy activation
B
iBEAMUSA.com
©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION
C
TE-WMCE
INSTALLATION INSTRUCTIONS
#IBEAMSAFETY
TABLE OF CONTENTS
Installation............................................................2-3
Wireless Pairing and Settings ...........................4-5
Wire Lenths ............................................................6
Specifications .........................................................7
TOOLS REQUIRED
• Wire stripper
• Tape
• Digital Multi-meter
• Cutter
Attention!
When testing the aftermarket
equipment, ensure that all factory equip-
ment is connected before cycling the key to
ignition.
REV. 07/20/2020 INSTTE-WMCE
Advertisement
Table of Contents
Related Manuals for iBeam TE-WMCE
Summary of Contents for iBeam TE-WMCE
- Page 1 A) Monitor and mount B) Camera C) Accessories Attention! When testing the aftermarket equipment, ensure that all factory equip- ment is connected before cycling the key to ignition. iBEAM Vehicle Safety Sytems ® iBEAMUSA.com ©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 07/20/2020 INSTTE-WMCE...
-
Page 2: Installation
MONITOR INSTALLATION Monitor install and wiring 1. Select the desired location and use the double stick tape to allow the monitor to be mounted to the dashboard (Figure A.). Slide the desired mount onto the back of the monitor. 2. Clean the surface on which you wish to mount the monitor and mount the monitor by either the double sided tape or suction cup. - Page 3 CAMERA INSTALLATION Camera Installation Mount the camera. Remove the tail light from the vehicle to allow access to the light bulbs wiring. (If help is needed, review the vehicles owners manual section on replacing the tail light bulbs.) (Figure A) Find the wiring that connects to the reverse bulb.
-
Page 4: Wireless Pairing And Settings
WIRELESS PAIRING AND SETTINGS Monitor to Camera pairing Before operation, the camera and monitor need to be paired to each other. Start by connecting power to both devices. If camera is connected to reverse, the vehicle must be Settings Settings put into the reverse gear. - Page 5 SETTINGS Brightness/Contrast Press the MENU button to enter into the settings menu, use the + and - buttons to Settings Settings navigate to the sun or half circle icons. Press “AV1/AV2” button to enter either setting. Use the + and - buttons to increase or decrease the set values.
-
Page 6: Wire Lenths
WIRE LENGTHS 30 in 8 FT 38 in 6.5 FT 386-257-1187 iBEAMUSA.com... -
Page 7: Specifications
SPECIFICATIONS TV SYSTEM NTSC EFFECTIVE PIXEL 1280 X 720 IP RATING - camera IP67 VISUAL ANGLE 70 degrees MIN. ILLUMINATION 0 Lux - w/ IRs active WORKING VOLTAGE 9 - 36V WORKING TEMP. -10 C ~ 65 C STORAGE TEMP. - 20 C ~ 85 C SCREEN SIZE 7 inch LCD... - Page 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra Recommends MECP certified technicians iBEAM Vehicle Safety Sytems ® iBEAMUSA.com ©COPYRIGHT 2020 METRA ELECTRONICS CORPORATION REV. 07/20/2020 INSTTE-WMCE...
Need help?
Do you have a question about the TE-WMCE and is the answer not in the manual?
Questions and answers