Related Manuals for NCTE 7300 Series
Summary of Contents for NCTE 7300 Series
- Page 1 Instruction manual and data sheet Torque Sensor Series 7300 Version 24/01 – State January 2024...
- Page 2 Copyright © NCTE AG® Torque Sensor Series 7300 Instruction Manual and Data Sheet. This instruction manual is property of NCTE AG®, D-82041 Oberhaching Unauthorized duplication, even in part, is not permitted. State: January 2024 Version 24/01 – State January 2024...
-
Page 3: Table Of Contents
Instruction manual General ..............................5 Customer Service Address ......................... 5 Warranty ............................5 Scope of delivery ..........................6 Declaration of conformity ......................... 7 Safety ................................. 8 Intended Use ............................. 8 Recalibration and duration of use ..................... 8 Structural change..........................8 Training of the operating personnel .................... - Page 4 Data Sheet Key Facts ..............................12 Torque ranges ............................12 Load characteristics ..........................13 Technical characteristics .......................... 13 EMV Emission data ..........................14 Dimensions .............................. 15 Wiring diagram ............................15 Sensor wiring ............................16 Speed sensor ............................16 10 Order options ............................17 11 Accessories ..............................
-
Page 5: Instruction Manual
All information without guarantee subject to technical changes. For further questions, we are of course also available after the purchase at any time. Please use our contact address. 1.1 Customer Service Address NCTE AG Raiffeisenalle 3 D-82041 Oberhaching Tel.:... -
Page 6: Scope Of Delivery
_______________________________________________________________________________________ 1.3 Scope of delivery The torque sensor system consists of a calibrated sensor, signal acquisition / -processing integrated in the housing, and the magnetized measuring shaft, which is installed between the (pto-)shaft and the attachment. Additionally, the package includes a connection cable and a retaining chain. Also included is the calibration certificate and safety instructions. -
Page 7: Declaration Of Conformity
_______________________________________________________________________________________ 1.4 Declaration of conformity _______________________________________________________________________________________ Version 24/01 – State January 2024 Page 7 to 18... -
Page 8: Safety
2.2 Recalibration and duration of use A factory recalibration should be executed annually. See the corresponding label on the sensor. This recalibration can be carried out quickly and easily by NCTE AG. Please contact us. If the sensor is used within the limits of its intended use and regularly calibrated, the sensor's operating life is unlimited. -
Page 9: Torque Sensor Series 7300
3.2 Assembly and disassembly The sensor of the 7300 series can be attached by a standardized shaft connector to the power take off shaft of a tractor. The sensor is secured (if configured that way) by a spring-loaded ball locking system, which... -
Page 10: Interface Description
Those aspects are especially true for the shaft and the bearing. In this case do not open the device. Contact NCTE AG directly. -
Page 11: Safety Instructions
Every 12 months Repairs and recalibrations can only be carried out by NCTE AG personnel. 3.10 Disposal The device must be returned to NCTE AG, Raiffeisenallee 3, D-82041 Oberhaching for disposal. _______________________________________________________________________________________ Version 24/01 – State January 2024 Page 11 to 18... -
Page 12: Data Sheet
1⅜'' 6-spline PTO Note: In case of overload, the sensor leads to a measurement offset. In such case, the sensor needs to be recalibrated at NCTE AG. The sensor should be operated only within the specified nominal torque range. _______________________________________________________________________________________ Version 24/01 –... -
Page 13: Load Characteristics
_______________________________________________________________________________________ Load characteristics Limit transverse Limit bending moment Model Axial force [N] force [N] [Nm] Series 3000 to be avoided to be avoided 7300 Any irregular stress (bending moment, transverse or axial force, exceeding the nominal torque) up to the specified static load limit is only permissible as long as none of the other stresses can occur. -
Page 14: Emv Emission Data
_______________________________________________________________________________________ Signal drift over temperature within nominal temperature %/10 K < 0.5 range Power supply Unit Value Power supply 9 … 28 Current consumption (max.) Start-up peak < 100 Absolute max. supply voltage General information Unit Value Protection class according to EN 60529 Reference temperature °C... -
Page 15: Dimensions
_______________________________________________________________________________________ Dimensions Wiring diagram Binder Plug Series 423/723/425 IP67 Type (Colour coding acc. to DIN 47100) Color Description Value White CAN / USB High/D- Brown CAN / USB Low/D+ Green rpm channel 0 … 5 V Yellow Gray Analog GND Analog output signal 0 …... -
Page 16: Sensor Wiring
_______________________________________________________________________________________ Sensor wiring Speed sensor Magnetic (Hall effect) speed sensor with 60 CPR. Parameters Min. Typ. Max. Unit Operating frequency 8000 Analog signal bandwidth Upper level output signal Lower level output signal _______________________________________________________________________________________ Version 24/01 – State January 2024 Page 16 to 18... -
Page 17: Order Options
SD card slot to use for data logging You can obtain further or additional accessories and special requests in a personal discussion with your contact person for series products by calling +49 (0)89 66 56 19 30 or by e-mail: sales@ncte.de. _______________________________________________________________________________________ Version 24/01 –... - Page 18 Your experts for magnetostrictive sensors...
Need help?
Do you have a question about the 7300 Series and is the answer not in the manual?
Questions and answers