Related Manuals for McConnel Power Arm 45
Summary of Contents for McConnel Power Arm 45
- Page 1 Power Arm 45 Publication 435 July 2003 Part No. 41570.35 HEDGE/GRASS TRIMMER Operator Manual...
- Page 2 UK DEALER WARRANTY INFORMATION & REGISTRATION VERIFICATION It is imperative that the selling dealer registers this machine with McConnel Limited within 7 days of delivery to the end user – failure to do so may affect the validity of the machine warranty.
-
Page 3: Ec Declaration Of Conformity
The Machinery Directive is fully implemented into UK law by means of the Supply of Machinery (Safety) Regulations 1992 (SI 1992/3073) as amended by The Supply of Machinery (Safety) (Amendment) Regulations 1994 (SI 1994/2063). Signed …………………………..……………………………………………………... on behalf of McCONNEL LIMITED Responsible Person Chief Design Engineer May 2005... -
Page 4: Read The Book First
READ THE BOOK FIRST It might save hours and pounds later ! When ordering spare parts always quote • The Machine Type • The Machine Serial Number • The Part Number Factory re-built service exchange units of the major hydraulic components are available from your Dealer NOISE The equivalent daily personal noise exposure from this machine, measured at... -
Page 5: General Information
Read this manual before fitting or operating the machine. Whenever any doubt exists contact your dealer or the McConnel Service Department for assistance. Use only McConnel Genuine spare parts on McConnel equipment and machines. DEFINITIONS - the following definitions apply throughout this manual: WARNING An operating procedure, technique etc., which can result in personal injury or loss of life if not... - Page 6 FEATURES PA45 – All models Linkage Mounted Left Hand Cutting Operator Guard Hydraulic Breakaway 45HP Hydraulic System 1.2m Centre Mount Supercut Flail Head PA45 SI models Semi Independent Hydraulics - (Tractor powered arm movement, P.T.O. pump for rotor) Rotor Engagement by Tractors PTO Lever Cable Controls PA45 TI models Totally Independent Hydraulics –...
- Page 8 This machine has the potential to be extremely dangerous, in the wrong hands it can kill or maim. It is therefore imperative that both owner, and operator of this machine, read and understand the following section to ensure that they are fully aware of the dangers that do, or may exist, and their responsibilities surrounding the use and operation of the machine.
- Page 9 BEFORE USING THIS MACHINE YOU MUST: ▲ Ensure you read all sections of the operator handbook. ▲ Ensure the operator is, or has been, properly trained to use the machine. ▲ Ensure the operator has been issued with and reads the operator handbook. ▲...
- Page 10 ▲ Always disengage the machine, kill the tractor engine, remove and pocket the key before dismounting for any reason. ▲ Always clear up all debris left at the work area, it may cause hazard to others. ▲ Always ensure when you remove your machine from the tractor that it is left in a safe and stable position using the stands and props provided and secured if necessary.
- Page 11 No advice given here can replace ‘good common sense’ and ‘total awareness’ at all times, but will go a long way towards the safe use of your McConnel machine.
- Page 13 FITTING Tractor Requirements Minimum tractor weight – including ballast weight if necessary: All models – 2500 kg Minimum HP requirements: All models – 45HP Linkage Type: Category l / ll P.T.O. Shaft: Tractor must be equipped with a ‘live drive P.T.O.’ to enable forward motion to be stopped while the flail head continues to operate.
- Page 14 VEHICLE / TRACTOR PREPARATION We recommend vehicles are fitted with cabs using ‘safety glass’ windows and protective guarding when used with our machines. Fit Operator Guard (part no. 73 13 324) using the hooks provided. Shape the mesh to cover all vulnerable areas. Remember the driver must be looking through mesh and/or polycarbonate glazing when viewing the flail head in any working position - unless the vehicle/ cab manufacturer...
-
Page 16: Initial Attachment
INITIAL ATTACHMENT • Choose a firm level site. • Cut banding straps and remove transport strap, loose items and stabiliser. -
Page 23: Oil Requirements
OIL REQUIREMENTS Tank Fill the reservoir to approximately 2” (50mm) below the top of the tank. The capacity is approximately 140 Litres (30 imp. Gallons) – Do not overfill. Supplier Cold or Temperate Climate Hot Climate Bartran 46 Bartran 68 Energol HLP-HM 46 Energol HLP-HM 68 CASTROL... -
Page 30: Arm Controls
ARM CONTROLS... -
Page 36: Hedge Cutting Procedure
HEDGE CUTTING HEDGE CUTTING PROCEDURE PROCEDURE 1. Cut the side and bottom of the field side 1. Cut the side and bottom of the field side first. This leaves the maximum thickness first. This leaves the maximum thickness of hedge on the road side to prevent the of hedge on the road side to prevent the possibility of any debris being thrown possibility of any debris being thrown... -
Page 39: Maintenance
MAINTENANCE LUBRICATION General Grease daily all the points indicated in the diagram above. Power Take-off Shaft The P.T.O. Shaft and its guards should be regularly examined. The universal joints should be greased very sparingly i.e. one shot of grease weekly. Note: Overgreasing of a universal joint will ‘blow out’... - Page 45 McConnel Limited, Temeside Works, Ludlow, Shropshire SY8 1JL. England. Telephone: 01584 873131. Facsimile: 01584 876463. www.mcconnel.com...
Need help?
Do you have a question about the Power Arm 45 and is the answer not in the manual?
Questions and answers